Browse Collections
-
SaleCicada Audio DSP600.4D — 4‑Channel Amplifier with DSP
Vendor:Cicada AudioMotorcycle Amplifier + DSP Cicada Audio DSP600.4D — Compact 4-Channel Power with Built-In DSP Clean power + smart control. The DSP600.4D packs a 4-channel class-D amp and a flexible DSP into a compact, bike-ready chassis. Dial in PEQ, high/low-pass filters up to 20 kHz, and steep slopes (up to 48 dB) so your Harley-Davidson® or Indian® system stays loud and clear at highway speed. Why Riders Choose It Built-in DSP — 8-band PEQ, HPF/LPF to 20 kHz, slopes 6/12/18/24/48 dB. Serious output — up to 152×4 @ 2Ω or 300×2 bridged @ 4Ω (14.4V). Compact chassis — fits cleanly behind fairings or in bags. Bike-ready — designed for motorcycle use. Plays nice with stock radios — easy gain structure and integration. Shop Motorcycle Amplifiers Best With Efficient front speakers (6.5″/horns) at 2–4Ω Rear lids or mid-bass channels with tailored PEQ & HPF/LPF Bridged 4Ω pairs for higher output OFC wiring, proper fusing, and careful gain setup Tell us your bike and speakers — we’ll pre-map crossovers, slopes, and PEQ to your setup. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 70 × 4 / 92 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 115 × 4 / 152 × 4 Bridged @ 4Ω (12.5V / 14.4V) 218 × 2 / 300 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 DSP Crossovers HPF/LPF 0–20 kHz; slopes 6/12/18/24/48 dB DSP PEQ 8 bands; Q 0.05–20 Operating Voltage 8 – 16 V Current Draw (Music / Max) 40 A / 80 A Recommended Fuse 40 A Efficiency ~79% Dimensions (L × W × H) 8.875″ × 4.0″ × 1.4″ (225.4 × 103 × 36 mm) Specs from Cicada’s product page and manual. Always verify impedance/wiring before power-on. Frequently Asked Questions — Motorcycle Audio Can I power fronts and lids with one amp? Yes, many builds run all four channels. Use the DSP to set independent HPF/LPF and PEQ per pair for clean, balanced output. Will it work with my factory radio? Yes — it integrates cleanly. Set gains carefully and use the DSP to correct the factory curve. Add a dedicated DSP if you need time alignment. Can I bridge for more power? Yes — bridge pairs at 4Ω for up to 300 W × 2 (14.4V). Enable LPF when driving mid-bass or a small sub. What wiring and fuse do I need? Use OFC power/ground sized for the current draw, fused at the battery (40 A). Keep grounds short with solid chassis bonding. Is it weather resistant? It’s designed for motorcycles. Mount away from direct spray and protect cables from abrasion and heat. Garage Bagger Stereo Advantage Bike-specific DSP presets on request Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and phone support Need Help? Call us at (864) 334-6131 with your bike, speakers, and goals. We’ll map crossovers, EQ, and gains for your exact setup.Sale -
SaleCicada Audio FLX1000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1000.4 — Compact 4-Channel Power for Bagger Audio Big output in a small chassis. The FLX1000.4 feeds your front + rear speakers real power from a palm-size, bike-ready amp. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a favorite for Harley-Davidson® and Indian® builds that need highway-clear sound without bulky gear. Why Riders Choose It Serious output — up to 254×4 @ 2Ω or 530×2 bridged @ 4Ω (14.4V). Compact chassis — 6.0″ × 4.9″ × 2.0″ fits behind fairings or in bags. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC options for easy integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring with correct fusing and clean grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 150 × 4 / 168 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 220 × 4 / 254 × 4 Bridged @ 4Ω (12.5V / 14.4V) 461 × 2 / 530 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) 60 A / 116 A Recommended Fuse (Music) 120 A Efficiency ~79% Dimensions (L × W × H) 6.0″ × 4.9″ × 2.0″ (152 × 124 × 51 mm) Specs from Cicada’s product page; retailer listings corroborate ratings and dimensions. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Can it run fronts and lids with one amp? Yes — many builds run four channels at 2–4Ω. Use HPF/LPF and proper gains for clean balance. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. Can I bridge it for more power? Yes — bridge pairs at 4Ω for up to ~530 W × 2 (14.4V). Use LPF for mid-bass or small sub duty. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (120 A music rec.). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX1400.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioCicada Audio FLX1400.4 4-Channel Motorcycle Amplifier The Cicada Audio FLX1400.4 is a high-output 4-channel motorcycle amplifier built for Harley-Davidson bagger audio systems that need serious clean power, strong speaker control, and reliable highway-speed output. This amplifier is a strong fit for riders powering fairing speakers, saddlebag lid speakers, midbass, or bridged speaker pairs in a loud, clean, motorcycle-ready audio build. Cicada Amplifiers Motorcycle Amplifiers Shop Cicada Audio THE REFERENCE STANDARD Clean 4-Channel Power for Harley Bagger Audio Built for riders who need compact motorcycle amplifier power, flexible crossover control, 2Ω/4Ω speaker support, and strong output for real Harley audio systems. Start a Build Consultation Call 864-334-6131 Key Product Details Product Cicada Audio FLX1400.4 4-Channel Motorcycle Amplifier Amplifier Type High-output 4-channel motorcycle amplifier Best For Harley-Davidson bagger audio, fairing speakers, saddlebag lid speakers, midbass, and amplified motorcycle audio systems System Goal Clean power, stronger output, better speaker control, and louder highway-speed performance Speaker Support 2Ω and 4Ω speaker systems, depending on final wiring and system design Install Focus Compact motorcycle amplifier layout for Harley-Davidson Touring and custom bagger audio builds Always verify speaker impedance, wiring layout, fuse size, amplifier placement, gain structure, and system design before ordering or installing this amplifier. Built for High-Output Harley Audio Systems The Cicada FLX1400.4 is built for Harley-Davidson and motorcycle audio systems where factory power is not enough. It gives riders the headroom needed to drive upgraded 6.5" speakers, 6x9 speakers, pro coaxials, midbass drivers, and bridged speaker pairs with cleaner output and better control. This amplifier is a strong choice when the goal is louder vocals, stronger midbass, reduced distortion, and better open-air performance at speed. In a properly planned Harley bagger audio system, the FLX1400.4 can support front and rear speaker layouts, fairing and lid speaker upgrades, or bridged power for more aggressive output. Power and Performance Specifications RMS Power @ 4Ω Approximately 200 watts x 4 channels at 14.4V RMS Power @ 2Ω Approximately 350 watts x 4 channels at 14.4V Bridged Power @ 4Ω Approximately 700 watts x 2 channels at 14.4V Frequency Response 20Hz–20kHz +/-3dB THD < 0.5% at 1kHz Signal-to-Noise Ratio Approximately 91dB A-weighted Damping Factor Approximately 200 Crossovers HPF / FULL / LPF, 30Hz–300Hz, 12dB/octave Turn-On Modes REM / DC turn-on support Operating Voltage 8V–16V Current Draw Approximately 70A music / 130A max Recommended Fuse Approximately 150A for music use Best Use for the FLX1400.4 The FLX1400.4 is best used in Harley-Davidson bagger audio builds that need strong 4-channel amplifier power for fairing speakers, saddlebag lid speakers, midbass, or bridged speaker layouts. It is built for riders who want more output without giving up control or clarity. Designed Around Real Motorcycle Audio Motorcycle audio is different from car audio. Wind noise, road speed, speaker placement, electrical load, and limited mounting space all matter. This amplifier belongs in systems where the speaker choice, wiring, fusing, and tuning plan are matched correctly. Recommended System Planning To get the best performance from the Cicada FLX1400.4, match it with the right speakers, proper OFC power and ground wiring, correct battery-side fusing, clean signal input, and a real tuning plan. For Harley-Davidson Touring and custom bagger audio systems, amplifier power should always be planned around the speakers, impedance, charging system, mounting location, and final sound goal. If you are unsure whether this amplifier is the right choice for your Road Glide, Street Glide, CVO, Road King, Indian, or custom motorcycle audio build, contact Garage Bagger Stereo before ordering. Related Cicada & Motorcycle Audio Paths Build the system around the correct amplifier, speakers, DSP, wiring, and installation parts. These related collections help match the FLX1400.4 with the right Harley audio upgrade path. Shop Cicada motorcycle amplifiers for Harley-Davidson audio builds Shop motorcycle amplifiers for Harley bagger audio systems Shop Cicada Audio speakers, amplifiers, DSP, and bagger audio upgrades Shop motorcycle DSP for Harley-Davidson audio tuning Shop motorcycle amplifier installation parts Need Help Choosing the Right Cicada Amplifier? Need help matching the Cicada FLX1400.4 to your speakers, bike, wiring, DSP, or complete Harley audio system? Call Garage Bagger Stereo or start a build consultation and we’ll help match the amplifier power, speaker layout, impedance, and tuning plan to your build. Call 864-334-6131 Start a Build ConsultationSale -
SaleCicada Audio FLX1400.4PRO 1400W 4-Channel DSP Motorcycle Amplifier
Vendor:Cicada AudioCicada Audio FLX1400.4PRO 1400W 4-Channel DSP Motorcycle Amplifier The Cicada Audio FLX1400.4PRO combines a high-output four-channel Class-D motorcycle amplifier with a full six-channel digital signal processor in one compact chassis. It delivers 350 watts RMS per channel at 2 ohms while giving professional installers the crossover, signal-routing and tuning control needed for serious Harley-Davidson, Indian and custom motorcycle audio systems. Four DSP channels feed the amplifier's internal outputs while two additional processed pass-through channels remain available for compatible system expansion. Bluetooth audio streaming, USB-C computer tuning and Cicada's DIALD DSP platform make the FLX1400.4PRO a complete power-and-processing solution for high-output bagger audio. THE REFERENCE STANDARD 1400 Watts of Power with Six-Channel DSP Control Four high-output amplified channels, two processed pass-through outputs and professional DSP control in a compact motorcycle-ready amplifier built for loud, clean highway performance. Start a Build Consultation Call 864-334-6131 FLX1400.4PRO Key Specifications Model FLX1400.4PRO Amplifier Type 4-Channel Class-D Motorcycle Amplifier with Built-In DSP DSP Architecture 6 Channels — 4 Amplified + 2 Pass-Through RMS Power @ 4Ω 225W × 4 @ 14.4V RMS Power @ 2Ω 350W × 4 @ 14.4V Bridged Power @ 4Ω 700W × 2 @ 14.4V Frequency Response 20 Hz – 20 kHz ±3 dB THD + Noise 0.1% @ 2Ω per channel at 10% rated power Signal-to-Noise Ratio 91 dB A-Weighted Damping Factor 200 Total Efficiency 80% Crossover Modes High-Pass / Band-Pass / Low-Pass Crossover Range 20 Hz – 20 kHz Crossover Slopes 6 / 12 / 24 / 48 dB per octave Input Sensitivity 0.2V – 12V Operating Voltage 9V – 16V Current Draw — Music 70A Current Draw — Maximum 150A Recommended Fuse 100A Power Input 4 AWG Speaker Outputs 12 AWG Busbar-Style Terminals Turn-On Modes REM / DC / VOX DSP Connectivity Bluetooth Audio Streaming / USB-C PC Tuning / DIALD DSP Dimensions with Brackets 8.26 × 4.9 × 2 in / 210 × 125 × 51 mm Chassis Dimensions 7.1 × 4.9 × 2 in / 180 × 125 × 51 mm Warranty 2 Years System planning note: Published amplifier output is measured at 14.4 volts. Actual output depends on motorcycle charging voltage, speaker impedance, wiring, electrical capacity, signal level and final DSP configuration. Four Amplified Channels Plus Two DSP Expansion Channels The FLX1400.4PRO is more than a four-channel amplifier. Its integrated DSP provides six processed outputs: four channels feed the internal Class-D amplifier while two additional DSP channels provide processed pass-through outputs for compatible future amplifiers. 225W × 4 @ 4Ω Strong four-channel output for compatible 4-ohm motorcycle speakers, component systems and high-efficiency coaxial configurations. 350W × 4 @ 2Ω Full 1400-watt output for properly configured 2-ohm motorcycle speaker systems requiring serious highway-speed authority. 700W × 2 Bridged The amplifier can be bridged into two compatible 4-ohm loads when the system design requires higher two-channel output. Built-In Six-Channel DSP Motorcycle audio requires more than amplifier power. Speaker location, wind noise, road noise, open-air listening and unequal distances from the rider all affect the final sound. The FLX1400.4PRO integrates the DSP control required to build the system around the motorcycle rather than relying only on basic amplifier controls. Six total DSP channels. Four internally amplified DSP outputs. Two processed pass-through outputs for compatible expansion. High-pass, band-pass and low-pass crossover modes. 20 Hz to 20 kHz crossover adjustment range. 6, 12, 24 and 48 dB-per-octave selectable slopes. Bluetooth audio streaming. USB-C computer tuning. Cicada DIALD PC and app-based DSP configuration. DSP advantage: Power alone does not create a properly tuned motorcycle audio system. Correct crossover points, signal level, output balance and system response are what allow that power to stay controlled and clean. Built for Harley-Davidson Bagger Audio Cicada engineered the FLX1400.4PRO around motorcycle installations, including direct mounting compatibility with compatible Harley-Davidson Road Glide and Street Glide amplifier rack locations. Its compact aluminum chassis delivers serious output without requiring the physical space normally associated with a 1400-watt four-channel amplifier. Road Glide Compact dimensions and multiple mounting options make the FLX1400.4PRO a strong amplifier platform for compatible Road Glide fairing installations. Street Glide Designed to work with compatible Street Glide amplifier rack layouts where mounting space is limited. Custom Baggers High power density and built-in DSP also make it useful for custom Harley-Davidson, Indian and powersports audio systems. Motorcycle-Ready Construction The FLX1400.4PRO uses an extruded aluminum heatsink and a conformal-coated circuit board to improve resistance to the vibration, moisture and dust encountered in motorcycle audio installations. Conformal-coated circuit board. Extruded aluminum amplifier chassis. Cicada ICAD overload protection circuitry. Status and clipping LED indicators. 4 AWG power connections. 12 AWG busbar-style speaker outputs. REM, DC and VOX turn-on modes. Molex input system supporting RCA or compatible Harley-specific termination. Bluetooth Audio and USB-C DIALD Tuning Built-in Bluetooth audio streaming provides a direct playback source for compatible testing, setup and listening. For deeper tuning control, USB-C connectivity allows a computer to connect directly to the amplifier's DSP. Cicada's DIALD platform provides PC and compatible app-based control over the FLX1400.4PRO DSP, giving installers the tools required to configure crossover behavior and system response around the actual motorcycle and speaker layout. Designed for Front, Rear and Component Systems Four high-output amplifier channels make the FLX1400.4PRO suitable for multiple motorcycle audio layouts. It can power front and rear speakers, component networks, saddlebag systems, lowers, fairing speakers or other properly matched combinations. Fairing and saddlebag speaker systems. Front and rear component configurations. 2-ohm high-output motorcycle speakers. 4-ohm coaxial and component systems. Mid-bass and pro-audio motorcycle speaker systems. Systems requiring processed outputs for an additional amplifier. Load planning matters: Always calculate the final impedance presented to each amplifier channel before wiring. Speaker count alone does not determine amplifier load. Electrical System Requirements Cicada specifies approximately 70 amps of music current draw and up to 150 amps maximum for the FLX1400.4PRO, with a recommended 100-amp fuse for the published music-load specification. Use properly sized OFC power and ground wiring. FLX1400.4PRO accepts 4 AWG power connections. Install appropriate battery-side fuse protection. Keep power and ground connections short, clean and secure. Confirm motorcycle battery condition before installation. Evaluate charging-system capacity for sustained high-output operation. Protect all wiring from heat, abrasion, sharp edges and moving components. Plug-and-Play Integration Options Garage Bagger Stereo offers this amplifier with optional bike-specific integration packages for multiple Harley-Davidson Touring generations. Choose the correct option for your motorcycle and radio configuration when ordering. Amplifier only. 2023.5+ Harley A2B integration without an additional external DSP. 2014–2023 Harley Touring with factory radio. 2014–2023 Harley Touring with aftermarket radio. 1998–2013 Harley Touring with factory radio. 1998–2013 Harley Touring with aftermarket radio. The exact harnessing and integration hardware varies by selected motorcycle generation and radio configuration. Verify your year, model, factory audio system and current radio before ordering. Installation and Tuning Verify final speaker impedance before connecting amplifier outputs. Confirm all power, ground and fuse requirements before installation. Mount the amplifier securely with adequate ventilation. Use correct signal integration for the motorcycle's radio and factory audio architecture. Set DSP crossover points around the actual speakers and enclosure configuration. Establish proper gain structure throughout the source, integration device and amplifier. Complete final DSP tuning after the motorcycle is fully assembled. Professional installation and system tuning are strongly recommended for high-output systems. Need Help Matching the FLX1400.4PRO to Your Bike? The right amplifier is only one part of a properly designed motorcycle audio system. Speaker impedance, radio integration, electrical capacity, crossover strategy, mounting location, wiring and DSP tuning all affect the final performance. Tell Garage Bagger Stereo your motorcycle year, model, radio, speakers and performance goal and we can help determine the correct FLX1400.4PRO configuration and integration path. Start a Build Consultation Call 864-334-6131Sale -
SaleCicada Audio FLX2000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioCicada Audio FLX2000.4 is a compact high-output four-channel motorcycle amplifier designed for Harley-Davidson, bagger, powersports, and custom audio systems. It delivers up to 542 watts RMS per channel at 2 ohms at 14.4 volts, supports 2-ohm and 4-ohm speaker systems, and provides bridgeable power, onboard crossover control, and motorcycle-ready construction for clean highway-speed output. Cicada Audio FLX2000.4 2000W 4-Channel Motorcycle Amplifier The Cicada Audio FLX2000.4 is a compact high-output 4-channel motorcycle amplifier built for Harley-Davidson bagger audio systems that need serious power, clean control, and highway-speed volume. With strong output at 2Ω and 4Ω, bridgeable power, onboard crossover control, and motorcycle-ready construction, the FLX2000.4 is built for riders who want more speaker authority without adding oversized amplifier hardware. Cicada Amplifiers Motorcycle Amplifiers Shop Cicada Audio THE REFERENCE STANDARD Big 4-Channel Power for Harley Bagger Audio Built for high-output Harley audio systems that need compact amplifier power, clean tuning control, 2Ω/4Ω speaker support, and serious open-air performance. Start a Build Consultation Call 864-334-6131 Key Product Details Product Cicada Audio FLX2000.4 2000W 4-Channel Motorcycle Amplifier Amplifier Type High-output 4-channel motorcycle amplifier Best For Harley-Davidson bagger audio, fairing speakers, saddlebag lid speakers, midbass, bridged speaker pairs, and high-output amplified motorcycle systems System Goal More power, stronger speaker control, louder open-air output, cleaner tuning, and better highway-speed performance Speaker Support 2Ω and 4Ω speaker systems, depending on final wiring and system design Install Focus Compact motorcycle amplifier layout for Harley-Davidson Touring, Road Glide, Street Glide, CVO, Indian, and custom bagger audio builds Always verify speaker impedance, wiring layout, fuse size, amplifier placement, gain structure, charging system capacity, and final system design before ordering or installing this amplifier. Built for Serious Harley-Davidson Audio Power The Cicada FLX2000.4 is made for riders who need more than basic motorcycle amplifier power. It is designed to drive upgraded 6.5" speakers, 6x9 speakers, pro coaxials, saddlebag lid speakers, midbass drivers, or bridged 4Ω speaker pairs with serious output and control. In a properly planned Harley-Davidson bagger audio system, the FLX2000.4 can support aggressive front and rear speaker layouts, bridged midbass power, or full custom speaker systems where clean volume and highway-speed performance are the priority. Power and Performance Specifications RMS Power @ 4Ω 275 watts x 4 channels at 12.5V / 331 watts x 4 channels at 14.4V RMS Power @ 2Ω 450 watts x 4 channels at 12.5V / 542 watts x 4 channels at 14.4V Bridged Power @ 4Ω 866 watts x 2 channels at 12.5V / 1044 watts x 2 channels at 14.4V Frequency Response 20Hz–20kHz +/-3dB THD < 0.5% at 1kHz Signal-to-Noise Ratio 91dB A-weighted Damping Factor 200 Crossovers HPF / FULL / LPF, 30Hz–300Hz, 12dB/octave Turn-On Modes REM / DC turn-on support Operating Voltage 8V–16V Current Draw 60A music / 240A max Recommended Fuse 120A for music use Efficiency Approximately 79% Gain Range 0.2V–12V Dimensions 8.6" x 4.9" x 2.0" / 218mm x 124mm x 51mm Best Use for the FLX2000.4 The FLX2000.4 is best used in Harley-Davidson and custom bagger audio builds that need strong 4-channel amplifier power for fairing speakers, saddlebag lid speakers, midbass, or bridged speaker pairs. Designed Around Real Motorcycle Audio Motorcycle audio is different from car audio. Wind noise, road speed, speaker placement, electrical load, limited mounting space, and heat management all matter. This amplifier belongs in systems where the speakers, wiring, fusing, and tuning plan are matched correctly. Recommended System Planning To get the best performance from the Cicada FLX2000.4, match it with the right speakers, proper OFC power and ground wiring, correct battery-side fusing, clean signal input, and a real tuning plan. For Harley-Davidson Touring and custom bagger audio systems, amplifier power should always be planned around the speakers, impedance, charging system, mounting location, and final sound goal. If you are unsure whether this amplifier is the right choice for your Road Glide, Street Glide, CVO, Road King, Indian, or custom motorcycle audio build, contact Garage Bagger Stereo before ordering. Related Cicada & Motorcycle Audio Paths Build the system around the correct amplifier, speakers, DSP, wiring, and installation parts. These related collections help match the FLX2000.4 with the right Harley audio upgrade path. Shop Cicada motorcycle amplifiers for Harley-Davidson audio builds Shop motorcycle amplifiers for Harley bagger audio systems Shop Cicada Audio speakers, amplifiers, DSP, and bagger audio upgrades Shop motorcycle DSP for Harley-Davidson audio tuning Shop motorcycle amplifier installation parts Need Help Choosing the Right Cicada Amplifier? Need help matching the Cicada FLX2000.4 to your speakers, bike, wiring, DSP, or complete Harley audio system? Call Garage Bagger Stereo or start a build consultation and we’ll help match the amplifier power, speaker layout, impedance, wiring, and tuning plan to your build. Call 864-334-6131 Start a Build ConsultationSale -
SaleCicada Audio FLX700.4 Motorcycle Amplifier
Vendor:Cicada AudioCicada Audio FLX700.4 4-Channel Motorcycle Amplifier The Cicada Audio FLX700.4 is a compact 4-channel motorcycle amplifier built for Harley-Davidson and Indian touring audio systems that need clean power, efficient output, and reliable highway-speed performance. With up to 175 watts x 4 at 2Ω, onboard crossover control, REM/DC turn-on, and a small motorcycle-ready chassis, the FLX700.4 is a strong fit for fairing speakers, saddlebag lid speakers, and clean amplified bagger audio builds. Cicada Amplifiers Motorcycle Amplifiers Shop Cicada Audio THE REFERENCE STANDARD Compact 4-Channel Power for Harley Audio Built for riders who need clean motorcycle amplifier power, compact installation, 2Ω/4Ω speaker support, and dependable output for real bagger audio systems. Start a Build Consultation Call 864-334-6131 Key Product Details Product Cicada Audio FLX700.4 4-Channel Motorcycle Amplifier Amplifier Type Compact 4-channel motorcycle amplifier Best For Harley-Davidson and Indian touring audio systems, fairing speakers, saddlebag lid speakers, coaxial speakers, and clean amplified motorcycle audio builds System Goal Clean power, stronger speaker output, better clarity, compact installation, and louder highway-speed performance Speaker Support 2Ω and 4Ω speaker systems, depending on final wiring and system design Install Focus Compact motorcycle amplifier layout for Harley-Davidson Touring, Road Glide, Street Glide, CVO, Indian, and custom bagger audio systems Always verify speaker impedance, wiring layout, fuse size, amplifier placement, gain structure, charging system capacity, and final system design before ordering or installing this amplifier. Built for Clean Harley-Davidson and Indian Audio Power The Cicada FLX700.4 is built for riders who want a clean, compact amplifier upgrade without overcomplicating the system. It gives Harley-Davidson and Indian touring motorcycles the power needed to run upgraded motorcycle-specific speakers with better clarity, stronger output, and more control than factory power alone. This amplifier is a strong choice for riders powering front fairing speakers, rear speakers, saddlebag lid speakers, or a balanced 4-channel motorcycle audio system. When matched with the right speakers, wiring, and tuning, the FLX700.4 helps the system stay cleaner and louder at speed. Power and Performance Specifications Channels 4 RMS Power @ 4Ω 125 watts x 4 channels RMS Power @ 2Ω 175 watts x 4 channels Bridged Power @ 4Ω 350 watts x 2 channels Crossovers HPF / LPF / FULL, 30Hz–300Hz Signal-to-Noise Ratio 95dB THD <0.1% Operating Voltage 8V–16V Fuse Rating 60A total, 2 x 30A Dimensions 11.5" x 5.1" x 1.8" Best Use for the FLX700.4 The FLX700.4 is best used in Harley-Davidson and Indian bagger audio builds that need compact 4-channel amplifier power for fairing speakers, rear speakers, saddlebag lid speakers, or efficient coaxial speaker systems. Designed Around Real Motorcycle Audio Motorcycle audio is different from car audio. Wind noise, road speed, speaker placement, electrical limits, wiring path, and mounting space all matter. This amplifier should be matched with the correct speaker load, clean wiring, and a proper tuning plan. Recommended System Planning To get the best performance from the Cicada FLX700.4, match it with efficient motorcycle-specific speakers, proper OFC power and ground wiring, correct battery-side fusing, clean signal input, and a real tuning plan. For Harley-Davidson Touring, Indian touring, and custom bagger audio systems, amplifier power should always be planned around the speakers, impedance, charging system, mounting location, and final sound goal. If you are unsure whether this amplifier is the right choice for your Road Glide, Street Glide, CVO, Road King, Indian, or custom motorcycle audio build, contact Garage Bagger Stereo before ordering. Related Cicada & Motorcycle Audio Paths Build the system around the correct amplifier, speakers, DSP, wiring, and installation parts. These related collections help match the FLX700.4 with the right Harley or Indian audio upgrade path. Shop Cicada motorcycle amplifiers for Harley-Davidson audio builds Shop motorcycle amplifiers for Harley bagger audio systems Shop Cicada Audio speakers, amplifiers, DSP, and bagger audio upgrades Shop motorcycle DSP for Harley-Davidson audio tuning Shop motorcycle amplifier installation parts Need Help Choosing the Right Cicada Amplifier? Need help matching the Cicada FLX700.4 to your speakers, bike, wiring, DSP, or complete Harley audio system? Call Garage Bagger Stereo or start a build consultation and we’ll help match the amplifier power, speaker layout, impedance, wiring, and tuning plan to your build. Call 864-334-6131 Start a Build ConsultationSale -
SaleCicada Audio FLX700.4PRO – 700W DSP Pro Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX700.4PRO — Compact 4-Channel Power with Built-In DSP Small chassis, big control. The FLX700.4PRO delivers clean power with an onboard 6-channel DSP (4 amplified + 2 pass-through), Bluetooth® streaming, and USB-C PC tuning. Designed for H-D® amp racks with multiple brackets, plus Molex® inputs for RCA or bike-specific termination. Why Riders Choose It Real output — 120×4 @ 4Ω, 175×4 @ 2Ω, or 350×2 bridged @ 4Ω (14.4V). 6-ch DSP onboard — tune crossovers/EQ on the bike; Bluetooth® audio built in. Bike-ready build — conformal-coated PCB in an extruded aluminum heatsink. Flexible turn-on — REM / DC / VOX with status & clipping LEDs. Premium I/O — 4 AWG power, 12 AWG speaker busbar-style terminals. Best With Front & rear pro speakers at 2–4Ω Bridged 4Ω pairs for lids/mid-bass OFC wiring, correct fusing, and solid grounds Factory radio or DSP signal — we’ll help map gains/filters Tell us your bike and speakers — we’ll pre-map crossovers and gains for highway-clear performance. Key Specifications RMS @ 4Ω (14.4V) 120 × 4 RMS @ 2Ω (14.4V) 175 × 4 Bridged @ 4Ω (14.4V) 350 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD + N (10% rated power) 0.1% @ 2Ω per ch SNR (A-wt) / Damping Factor 91 dB / 200 DSP / Tuning 6-ch DSP (4 amp + 2 pass), Bluetooth® audio, USB-C PC tuning Turn-On Modes REM / DC / VOX Operating Voltage 9 – 16 V Current Draw (Music / Max) 50 A / 80 A Recommended Fuse (Music) 50 A Efficiency ~80% Gain Range 0.2 – 12 V Dimensions (with brackets) 5.3″ × 4.9″ × 2.0″ (134 × 125 × 51 mm) Dimensions (chassis) 4.1″ × 4.9″ × 2.0″ (104 × 125 × 51 mm) Specs per Cicada Audio product page. Always verify wiring/impedance and set gains conservatively. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean OFC wiring and correct fusing On-bike DSP tuning for loud, clear highway sound Nationwide shipping & tech support Need Help? Call (864) 334-6131. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleDB Drive Euphoria XPERT EX100.4 Full Range Class D 4-Channel Amplifier
Vendor:DB DriveTRUE SOUND. TRUE SOURCE. EX100.4 : 4 Channel Full Range Class D Amplifier Achieve superior audio performance with the XPERT EX100.4, engineered for high output in a compact design—ideal for motorcycle and space-limited applications. Capable of powering high-performance tweeter, compression drivers, and midranges with ease. Features 4 Channel Class D Circuitry ACT - Adaptive Crossover Technology High efficiency Full Range Class D Technology Direct Connect Speaker Terminals Large Gauge Power Wire Inputs APC - Audio Protection Circuit SESI - Signal Evaluation Status Indicator $299.98 Specifications @14.4 Volts - 1% THD 4 x 50 Watts @ 4 Ohm 4 x 100 Watts @ 2 Ohm 2 x 200 Watts @ 4 Ohm (Bridged) Working Voltage: 10 - 16 Volts Frequency Response: 10Hz - 20KHz Signal to Noise Ratio: < 85dB Damping Factor @ 4 Ohm > 57/ 1KHz Low Level Input: 6V - 0.2V Ch 1/2 High Pass Filter Variable: 20Hz - 5KHz Ch 1/2 Low Pass Filter Variable: 50Hz - 5KHz Ch 3/4 High Pass Filter Variable: 20Hz - 5KHz Ch 3/4 Low Pass Filter Variable: 50Hz - 5KHz Minimum Working Impedance: 2 Ohm Stereo Dimensions L - 5" / 127mm W - 5.20" / 132.08mm H - 2.50" / 63.50mmSale -
SaleDB Drive Euphoria XPERT EX200.4 Full Range Class D 4-Channel Amplifier
Vendor:DB DriveTRUE SOUND. TRUE SOURCE. EX200.4 : 4 Channel Full Range Class D Amplifier Achieve superior audio performance with the XPERT EX200.4, engineered for high output in a compact design—ideal for motorcycle and space-limited applications. Capable of powering high-performance tweeter, compression drivers, and midranges with ease. Features 4 Channel Class D Circuitry ACT - Adaptive Crossover Technology High efficiency Full Range Class D Technology Direct Connect Speaker Terminals Large Gauge Power Wire Inputs APC - Audio Protection Circuit SESI - Signal Evaluation Status Indicator $599.98 Specifications @14.4 Volts - 1% THD 4 x 200 Watts @ 4 Ohm 4 x 300 Watts @ 2 Ohm 2 x 400 Watts @ 4 Ohm (Bridged) Working Voltage: 10 - 16 Volts Frequency Response: 10Hz - 20KHz Signal to Noise Ratio: < 95dB Damping Factor @ 4 Ohm > 101/ 1KHz Low Level Input: 6V - 0.2V Ch 1/2 High Pass Filter Variable: 20Hz - 5KHz Ch 1/2 Low Pass Filter Variable: 50Hz - 5KHz Ch 3/4 High Pass Filter Variable: 20Hz - 5KHz Ch 3/4 Low Pass Filter Variable: 50Hz - 5KHz Minimum Working Impedance: 2 Ohm Stereo Dimensions L - 7.45" / 189.23mm W - 5.20" / 132.08mm H - 2.50" / 63.50mmSale -
SaleDB Drive Euphoria XPERT EX300.4 Full Range Class D 4-Channel Amplifier
Vendor:DB DriveTRUE SOUND. TRUE SOURCE. EX300.4 : 4 Channel Full Range Class D Amplifier Achieve superior audio performance with the XPERT EX300.4, engineered for high output in a compact design—ideal for motorcycle and space-limited applications. Capable of powering high-performance tweeter, compression drivers, and midranges with ease. Features 4 Channel Class D Circuitry ACT - Adaptive Crossover Technology High efficiency Full Range Class D Technology Direct Connect Speaker Terminals Large Gauge Power Wire Inputs APC - Audio Protection Circuit SESI - Signal Evaluation Status Indicator $699.98 Specifications @14.4 Volts - 1% THD 4 x 300 Watts @ 4 Ohm 4 x 500 Watts @ 2 Ohm 2 x 600 Watts @ 4 Ohm (Bridged) Working Voltage: 10 - 16 Volts Frequency Response: 10Hz - 20KHz Signal to Noise Ratio: < 95dB Damping Factor @ 4 Ohm > 114/ 1KHz Low Level Input: 6V - 0.2V Ch 1/2 High Pass Filter Variable: 20Hz - 5KHz Ch 1/2 Low Pass Filter Variable: 50Hz - 5KHz Ch 3/4 High Pass Filter Variable: 20Hz - 5KHz Ch 3/4 Low Pass Filter Variable: 50Hz - 5KHz Minimum Working Impedance: 2 Ohm Stereo Dimensions L - 9" / 228.6mm W - 5.20" / 132.08mm H - 2.50" / 63.50mmSale -
SaleDiamond Audio DXM1000.6D 6-Channel Waterproof Full Range Amplifier 1000W RMS
Vendor:Diamond AudioDiamond Audio - DXM1000.6D DXM Series Monoblock 1000W RMS Class D Waterproof Amplifier All weather amplifier for your OUTDOOR life (IPX67 Rated) Specifications Ratings: Power @ 2Ω: 150W RMS x 6 Power @ 4Ω: 100W RMS x 6 Power @ 4Ω Bridged: 340W RMS x 3CH Total Harmonic Distortion: <0.3% S/N Ratio (1W@4Ω): >-96dB Gain Range: 0.2v-10v Crossover Range: 40Hz-400Hz Frequency Range: 10Hz-33KHz Current Draw Full Power (Music): 105A (10.5A) AVG Fuse Rating: 50A Dimensions: 11.8”x4.3”x1.7” (298.6mm x 110mm x 44.0mm) Features Power & Protection Led Light Status Indicator Short circuit, thermal, and voltage protection Selectable X-Over: LPF/FULL/HPF Selectable Input Modes: 2CH/6CH IPX67 Rated Remote Bass Knob Included DXM Series Amplifier Manual DXM1000.6D One SheetSale -
SaleDiamond Audio DXM600.2D 2-Channel Waterproof Full Range Amplifier 600W RMS
Vendor:Diamond AudioDiamond Audio - DXM600.2D DXM Series 2-Channel 600W RMS Full Range Class D Waterproof Amplifier All weather amplifier for your OUTDOOR life (IPX67 Rated) Specifications Ratings: Power @ 2Ω: 300W RMS x 2 Power @ 4Ω: 200W RMS x 2 Power @ 4Ω Bridged: 600W RMS x 1 Total Harmonic Distortion: <0.3% S/N Ratio (1W@4Ω): >-102dB Gain Range: 0.2v-10v Crossover Range: 40Hz-400Hz Frequency Range: 10Hz-33KHz Bass Boost: 0dB-18dB Current Draw Full Power(Music): 70A (7A) AVG Fuse Rating: 35A Dimensions: 9.5”x4.3”x1.7” (241.6mm x 110mm x 44.0mm) Features Power & Protection Led Light Status Indicator Short Circuit, Thermal and Voltage Protection Selectable X-Over: LPF/FULL/HPF IPX67 Rated DXM Series Amplifier ManualDXM600.2D One SheetSale
Motorcycle Amplifiers
Motorcycle amplifiers are the backbone of any properly built touring audio system. This collection includes purpose-built amplifiers engineered specifically for Harley Davidson and Indian touring motorcycles where space, electrical stability, and sustained output matter.
These amplifiers are selected for motorcycle-specific requirements — compact chassis design, high efficiency, thermal management, and clean output at real riding speeds. They are designed to integrate correctly with factory radios, factory premium audio systems, and aftermarket DSP processors without signal degradation or reliability issues.
This collection supports a wide range of build levels, including:
- 4-channel amplifiers for fairing and saddlebag speaker systems
- Monoblock amplifiers for motorcycle subwoofers
- DSP-integrated amplifiers for signal correction and tuning
- Plug-and-play amplifier solutions for select Harley touring platforms
Plug-and-play amplifier options allow direct integration using model-specific harnessing, eliminating cutting or splicing while maintaining proper signal integrity. For higher-output or custom builds, traditional power and signal architectures are fully supported.
All amplifiers in this collection are vetted for proper impedance handling, clean pre-amp compatibility, and long-term stability in motorcycle environments. These are not generic car amplifiers — they are selected to perform reliably on touring motorcycles with limited space and demanding operating conditions.
This page serves as a central power solution hub for staged upgrades and full system builds across Harley and Indian touring platforms.
Complete Your Audio System
Harley Plug-and-Play Audio Kits
Motorcycle DSP Processors
Speaker Installation Parts
Custom Motorcycle Audio Builds
Cutting-Edge technology for Superior Sound
Our motorcycle amplifiers are equipped with the latest technology to deliver unmatched sound quality. From Class D amplifiers that provide efficient power with minimal current draw to advanced audio systems that ensure clear audio signals, our amps are built for the audiophile rider. With available features like high pass filters and watts RMS ratings, you'll enjoy every note and beat with precision and clarity.
Compact Designs for Easy Installation
We understand that space is a premium when it comes to motorcycle audio. That's why we carry amplifier choices that come with a small footprint and are designed for easy installation in tight spaces. Whether you're fitting an amp in your Harley-Davidson's fairing or under a seat, we carry everything you need, including wiring harnesses and installation instructions. Say goodbye to bulky amps and hello to sleek, powerful audio solutions.
Built for the Road
Our motorcycle amplifiers are not just about great sound; they're also built to withstand the rigors of the road. From vibration-resistant amp enclosures to weatherproof designs, our amps are ready for any adventure. Whether you're riding a Road Glide or an off-road vehicle, our amplifiers are engineered to perform in any environment, ensuring your music never skips a beat.
Customize Your Sound Expierence
Take control of your audio experience with our motorcycle amplifiers. With features like volume control, adjustable power ratings, and multiple channel options, you can tailor your sound system to your preferences. Whether you're looking for a powerful bass or clear highs, our amplifiers provide the flexibility to create the perfect audio setup for your ride.
Garage Bagger: Only Carrying the Best
At Garage Bagger Stereo, we're dedicated to providing top-tier audio equipment, and our Motorcycle Amplifiers are a prime example of the elite brands we offer. Understanding the importance of excellent sound for your ride or sail, we feature an exceptional range of parts. We know selecting the right gear can be daunting, so our expert team, armed with extensive knowledge and enthusiasm for audio, is ready to assist you in finding the ideal setup for your motorcycle or boat. Thank you for considering Dirty Bird at Garage Bagger Stereo, where premium quality and expert guidance are our standards.