Browse Collections
-
Arc Audio PSM Pro Digital Sound Processor | Plug and Play
Vendor:Arc AudioHarley Davidson Minature Pro Digital Sound Processor Plug and Play for stock radios 14-23 Harley Davidson Models Plug and Play for stock radios and amps 23 CVO to current Harley Davidson Models The ARC Audio PSM Pro digital sound processor is a small but powerful device designed to enhance the audio quality of your car or motorcycle's sound system. It is an upgraded version of the PSM offering even better performance and 8 output channels.The PSM Pro uses advanced 32-bit DSP technology and has 296 total bands of full variable parametric equalization, open architecture crossover selection, signal delay, and phase control. This allows you to tune your audio system to your specific preferences and improve the quality of your listening experience. Processor Type Stand Alone Unit Processor Resolution 32-Bits Sample Rate 96kHz Analog Inputs 6 CH. Differential in (RCA or Speaker Level) Input Sensitivity 2V - 16V RMS Digital Inputs Coaxial Auto-sense Turn-On DC (BTL) (Uses Ch 1/2 Inputs Only) Outputs (RCA) 8-Channels Outputs Voltage (RCA) Up to 3.5V Input Impedance (RCA) 10k ohms Frequency Response 20Hz - 23.5kHz S/N Ratio 1V 1:1 86dB S/N 4V 1:1 90dB Operating Voltage 6V - 17.0V (Start Stop Compliance to 4.5V) Output Equalization 31 Band + 6 (37 Band) X 8 Parametric EQ, Highpass Shelf, Lowpass Shelf, 1st & 2nd order Allpass. (296 Total Bands Output Equalization Resolution 0.01dB dB per step +18dB / -24dB Output Signal Delay Up to 30ms per channel in .01ms increments (Fixed Point Delay) Input Signal Mixer Yes - 8-Channels In (Including Digital) x 8-Channels Out Advanced Mixer (Output Signal Mixer) Yes Easy-to-use Mixer Assistant Yes Crossovers Phase Correct AP/HP/LP/BP all channels Crossover Slopes 6dB, 12dB, 18dB, 24dB, 30dB, 36dB, 42dB, 48dB Slopes all bands all channels Crossover Types Butterworth, Linkwitz-Riley, Bessel, Variable Q, Chebyshev (all channels all bands) Crossover selectable frequencies 10Hz - 20kHz in 0.1 Hz increments) Output Signal up mixer Yes Input Signal Equalization 12 Bands Parametric (linkable) Per Channel Input Equalization Resolution 1/10th dB per step +18dB / -24dB Input Equalization All Pass Filters Yes - Individual per input EQ band Input Signal Delay Yes - Up to 11.04ms per channel input Presets Up to 4-Presets External Remote Level Control Yes (LR1 Sold Separately) AXP WiFi control adapter card No Preset selection without controller use Yes - Optional manual trigger switches +/- for up to 4 presets (Not Included) Remote Turn-On Output Controls Turn on Output (up to 40ms), Turn-on Hold (up to 40ms), Auto-sense hold time (up to 200ms) Remote Turn-On Output On/Off lead timing control Remote on/off adjustable up to 40 seconds each Maestro AR Module interface capable Yes - Requires Maestro T-Harness, and data cable for connection. Expansion Capability PSM-Pro can be run in multiples with individual USB connections to a single PC with single operating software being used Software Interface 64 bit Windows 8, Windows 8.1 or Windows 10 Dimensions 3.75"(L) x 3.0"(W) x 1.35"(H) -
SaleCicada Audio DSP600.4D — 4‑Channel Amplifier with DSP
Vendor:Cicada AudioMotorcycle Amplifier + DSP Cicada Audio DSP600.4D — Compact 4-Channel Power with Built-In DSP Clean power + smart control. The DSP600.4D packs a 4-channel class-D amp and a flexible DSP into a compact, bike-ready chassis. Dial in PEQ, high/low-pass filters up to 20 kHz, and steep slopes (up to 48 dB) so your Harley-Davidson® or Indian® system stays loud and clear at highway speed. Why Riders Choose It Built-in DSP — 8-band PEQ, HPF/LPF to 20 kHz, slopes 6/12/18/24/48 dB. Serious output — up to 152×4 @ 2Ω or 300×2 bridged @ 4Ω (14.4V). Compact chassis — fits cleanly behind fairings or in bags. Bike-ready — designed for motorcycle use. Plays nice with stock radios — easy gain structure and integration. Shop Motorcycle Amplifiers Best With Efficient front speakers (6.5″/horns) at 2–4Ω Rear lids or mid-bass channels with tailored PEQ & HPF/LPF Bridged 4Ω pairs for higher output OFC wiring, proper fusing, and careful gain setup Tell us your bike and speakers — we’ll pre-map crossovers, slopes, and PEQ to your setup. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 70 × 4 / 92 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 115 × 4 / 152 × 4 Bridged @ 4Ω (12.5V / 14.4V) 218 × 2 / 300 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 DSP Crossovers HPF/LPF 0–20 kHz; slopes 6/12/18/24/48 dB DSP PEQ 8 bands; Q 0.05–20 Operating Voltage 8 – 16 V Current Draw (Music / Max) 40 A / 80 A Recommended Fuse 40 A Efficiency ~79% Dimensions (L × W × H) 8.875″ × 4.0″ × 1.4″ (225.4 × 103 × 36 mm) Specs from Cicada’s product page and manual. Always verify impedance/wiring before power-on. Frequently Asked Questions — Motorcycle Audio Can I power fronts and lids with one amp? Yes, many builds run all four channels. Use the DSP to set independent HPF/LPF and PEQ per pair for clean, balanced output. Will it work with my factory radio? Yes — it integrates cleanly. Set gains carefully and use the DSP to correct the factory curve. Add a dedicated DSP if you need time alignment. Can I bridge for more power? Yes — bridge pairs at 4Ω for up to 300 W × 2 (14.4V). Enable LPF when driving mid-bass or a small sub. What wiring and fuse do I need? Use OFC power/ground sized for the current draw, fused at the battery (40 A). Keep grounds short with solid chassis bonding. Is it weather resistant? It’s designed for motorcycles. Mount away from direct spray and protect cables from abrasion and heat. Garage Bagger Stereo Advantage Bike-specific DSP presets on request Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and phone support Need Help? Call us at (864) 334-6131 with your bike, speakers, and goals. We’ll map crossovers, EQ, and gains for your exact setup.Sale -
SaleDiamond Audio NEO10001DSP — 1000W RMS Monoblock Amplifier w/ DSP
Vendor:Diamond AudioProduct Overview Video Diamond Audio NEO10001DSP 1000W RMS Monoblock Amplifier with 4CH DSP The Diamond Audio NEO10001DSP combines dedicated monoblock power with an integrated 4-channel digital signal processor in a compact Class D chassis. Designed for subwoofer, midbass, and low-frequency applications, it delivers up to 1000 watts RMS at 1 ohm while providing precise control over EQ, crossovers, time delay, OEM integration, and system expansion. With 600 watts RMS at 4 ohms, 800 watts RMS at 2 ohms, and 1000 watts RMS at 1 ohm, the NEO10001DSP gives motorcycle, powersports, marine, and custom-audio systems strong low-frequency output without requiring a separate standalone DSP. View NEO10001DSP Diamond Audio Amplifiers Motorcycle Amplifiers THE REFERENCE STANDARD Monoblock Power with Integrated DSP Control Built for motorcycle and powersports systems that need strong low-frequency output, advanced tuning, OEM signal integration, and flexible system expansion from one compact amplifier. Start a Build Consultation Call 864-334-6131 Diamond Audio NEO10001DSP Key Specifications Model NEO10001DSP Amplifier Type Class D 1-Channel Monoblock Amplifier with Integrated 4-Channel DSP Power @ 4Ω 600W RMS x 1 Power @ 2Ω 800W RMS x 1 Power @ 1Ω 1000W RMS x 1 DSP Architecture 4 channels total: 2 internal DSP channels + 2 RCA preamp outputs Parametric EQ 31 bands per DSP channel DSP Controls Parametric EQ, crossovers, time delay, channel linking, gain and system configuration Programming PC and Android programming support Bluetooth Built-in Bluetooth audio streaming Input Sensitivity 0.4V – 20V Selectable Load Resistors 10Ω, 20Ω, 60Ω and 20kΩ Operating Voltage Range 8V – 17V RCA Preamp Outputs 2 channels Frequency Response 10Hz – 30kHz Signal-to-Noise Ratio 95dB THD & Noise ≤0.03% Dimensions 8.8″ x 4.07″ x 1.38″ Net Weight 2.40 lbs Remote Compatibility Diamond Audio NeoDRC1 Remote Commander — sold separately Construction Marine-ready, water-resistant chassis Fitment warning: Verify amplifier placement, mounting clearance, wiring path, ventilation, and complete system layout before ordering or installation. 1000W RMS Dedicated Low-Frequency Power The NEO10001DSP is built for applications that need substantial output from a single low-frequency channel. It can be used with compatible subwoofers, midbass drivers, or other low-frequency speaker configurations where high current capability and precise signal control are required. 600W RMS @ 4Ω Provides strong output for compatible higher-impedance subwoofer and midbass configurations. 800W RMS @ 2Ω Increased output for compatible 2-ohm low-frequency speaker systems. 1000W RMS @ 1Ω Full rated monoblock output for compatible 1-ohm loads and high-output bass systems. Integrated 4-Channel DSP Although the NEO10001DSP is a monoblock amplifier, Diamond Audio integrates a 4-channel DSP platform into the chassis. Two DSP channels manage the internal amplifier signal path while two additional RCA preamp outputs can feed another amplifier or system component. 31-Band Parametric EQ Detailed frequency adjustment allows precise control of the low-frequency response and integration with the rest of the audio system. Crossovers and Time Delay Configure frequency limits and timing so the low-frequency system integrates properly with fairing, pod, saddlebag, or full-range speakers. Channel Linking DSP channel linking simplifies adjustments when multiple outputs require coordinated tuning. PC and Android Programming Diamond Audio provides programming support for detailed DSP configuration and system tuning. OEM Signal Integration The NEO10001DSP includes several integration tools for factory audio systems where conventional low-level RCA outputs may not be available. High- and low-level signal input capability from 0.4V up to 20V. Selectable onboard 10Ω, 20Ω, 60Ω, and 20kΩ load resistors. 8V to 17V operating-voltage compatibility. DSP-based signal management for complex OEM and aftermarket system layouts. Two RCA preamp outputs for additional amplifier expansion. Integration note: High-level input capability and selectable load resistors do not automatically make every factory motorcycle audio system plug-and-play. Verify the source unit, factory amplifier, signal type, required interface, and complete integration strategy before installation. Bluetooth Audio Streaming Built In Diamond Audio includes Bluetooth audio streaming directly in the NEO10001DSP. Compatible devices can stream audio directly to the amplifier and DSP without requiring the source signal to originate from a conventional head unit input. Diamond Audio also lists smartphone-control capability as part of the NEO platform, with dedicated iOS and Android app control continuing to develop separately from the amplifier's core DSP and Bluetooth functions. Designed for Motorcycle, Marine and Powersports Systems The NEO10001DSP uses a marine-ready, water-resistant chassis and compact form factor suited to motorcycle, powersports, marine, and custom installations where amplifier space can be limited. Water-Resistant Chassis Designed for demanding installations where moisture and environmental exposure must be considered. Staggered RCA Connections Connection placement helps simplify signal-wire routing and cable management in tight installations. Quick-Connect Power Block High-current removable power connections support cleaner installation and service access. Installation and System Planning Verify amplifier mounting space before ordering. Confirm the final speaker or subwoofer impedance presented to the amplifier. Match amplifier output to the RMS capability of the connected driver or drivers. Verify the motorcycle's source-unit and factory-amplifier signal configuration. Determine whether high-level inputs, RCA inputs, load resistors, or an external integration interface will be used. Plan use of the two DSP-controlled RCA outputs if additional amplification is part of the system. Verify battery, charging-system, wiring, fuse, and ground capacity for the complete audio system. Complete DSP tuning only after the entire system is installed and operating correctly. Need Help Designing the System? The NEO10001DSP combines amplifier power and DSP control in one chassis, but correct impedance, signal integration, electrical capacity, crossover strategy, and system tuning still determine how well the final installation performs. Start a Build Consultation Call 864-334-6131Sale -
Diamond Audio NEO12004DSP — 1200W RMS 4-Channel Amplifier w/ DSP
Vendor:Diamond AudioProduct Overview Video Diamond Audio NEO12004DSP 1200W RMS 4-Channel Amplifier with 6CH DSP The Diamond Audio NEO12004DSP combines four channels of high-efficiency Class D amplification with an integrated 6-channel digital signal processor in a compact chassis built for motorcycle, powersports, marine, and custom audio systems. It delivers 150 watts RMS x 4 at 4 ohms, 300 watts RMS x 4 at 2 ohms, or up to 600 watts RMS x 2 bridged at 4 ohms, while providing detailed control over EQ, crossovers, time delay, channel linking, OEM integration, Bluetooth streaming, and system expansion. View NEO12004DSP Diamond Audio Amplifiers Motorcycle Amplifiers THE REFERENCE STANDARD Four Channels of Power. Six Channels of DSP Control. Built for motorcycle audio systems that need strong multi-channel output, bridgeable power, professional tuning control, OEM integration, and flexible expansion from one compact amplifier. Start a Build Consultation Call 864-334-6131 Diamond Audio NEO12004DSP Key Specifications Model NEO12004DSP Amplifier Type Class D 4-Channel Amplifier with Integrated 6-Channel DSP Total Rated Output 1200W RMS Power @ 4Ω 150W RMS x 4 Power @ 2Ω 300W RMS x 4 Bridged @ 4Ω 600W RMS x 2 DSP Architecture 6 channels total: 4 internal amplified channels + 2 RCA preamp outputs Parametric EQ 31 bands per DSP channel DSP Controls Parametric EQ, crossovers, time delay, channel linking, gain and system configuration Programming PC and Android programming support Bluetooth Built-in Bluetooth audio streaming Input Sensitivity 0.4V – 20V Selectable Load Resistors 10Ω, 20Ω, 60Ω and 20kΩ Operating Voltage Range 8V – 17V RCA Preamp Outputs 2 channels Frequency Response 15Hz – 23kHz Signal-to-Noise Ratio 85dB THD & Noise ≤0.03% Dimensions 8.8″ x 4.07″ x 1.38″ Net Weight 2.25 lbs Remote Compatibility Diamond Audio NeoDRC1 Remote Commander — sold separately Construction Marine-ready, water-resistant chassis Fitment warning: Verify amplifier placement, mounting clearance, wiring path, ventilation, and complete system layout before ordering or installation. 1200W RMS 4-Channel Class D Power The NEO12004DSP is designed for systems that need flexible multi-channel output without stacking multiple amplifiers. Four amplified channels can power fairing speakers, saddlebag speakers, lower pods, tour-pack speakers, active component systems, or other compatible speaker combinations. 150W x 4 @ 4Ω Provides clean rated power for compatible 4-ohm motorcycle, powersports, and marine speakers. 300W x 4 @ 2Ω Increased output for compatible 2-ohm high-performance speaker systems. 600W x 2 Bridged @ 4Ω Bridge channel pairs for applications requiring substantially higher output from two channels. Integrated 6-Channel DSP The NEO12004DSP combines four amplified channels with two additional RCA preamp outputs, creating a 6-channel DSP platform. That allows the amplifier to manage its own powered channels while also controlling signal for an additional amplifier or system component. 31-Band Parametric EQ Per Channel Detailed frequency adjustment allows precise tuning of individual speakers and system zones. Crossovers and Time Delay Configure frequency ranges and timing for fairing speakers, pods, saddlebag speakers, tweeters, midbass drivers, and other system components. Channel Linking Linked-channel controls simplify tuning when multiple amplifier channels require matching adjustments. PC and Android Programming Professional DSP programming support provides detailed access to system configuration and tuning controls. OEM Audio System Integration The NEO12004DSP includes signal-integration tools for motorcycles and vehicles where the factory source unit or amplifier may not provide conventional low-level RCA outputs. High- and low-level signal input capability from 0.4V up to 20V. Selectable onboard 10Ω, 20Ω, 60Ω, and 20kΩ load resistors. 8V to 17V operating-voltage compatibility. DSP-based signal management for complex factory and aftermarket system layouts. Two DSP-controlled RCA preamp outputs for system expansion. Integration note: High-level input capability and selectable load resistors do not automatically make every OEM motorcycle audio system plug-and-play. Verify the source unit, factory amplifier, signal type, required interface, and complete integration strategy before installation. Bluetooth Audio Streaming Built In Diamond Audio includes Bluetooth audio streaming directly in the NEO12004DSP. Compatible devices can stream audio directly to the amplifier and DSP without requiring the source signal to originate from a conventional head unit input. Diamond Audio also lists smartphone-control capability through the NEO platform, with dedicated iOS and Android app control listed as coming soon. Designed for Motorcycle, Marine and Powersports Systems The NEO12004DSP uses a marine-ready, water-resistant chassis and compact 8.8-inch footprint suited to motorcycle, powersports, marine, and custom installations where amplifier space is limited. Water-Resistant Chassis Designed for demanding installations where moisture and environmental exposure must be considered. Staggered RCA Connections Connection placement helps simplify signal-wire routing and cable management in tight installations. Quick-Connect Power Block High-current removable power connections support cleaner installation and easier service access. Installation and System Planning Verify amplifier mounting space and clearance before ordering. Confirm speaker impedance and RMS power requirements for every channel. Determine whether channels will operate independently or in bridged configurations. Verify the motorcycle's source-unit and factory-amplifier signal configuration. Determine whether high-level inputs, RCA inputs, load resistors, or an external integration interface will be used. Plan use of the two DSP-controlled RCA outputs if additional amplification is part of the system. Verify battery, charging-system, wiring, fuse, and ground capacity for the complete audio system. Complete final DSP tuning only after the entire system is installed and operating correctly. Need Help Designing the System? The NEO12004DSP gives installers considerable flexibility, but correct speaker loading, bridging, signal integration, electrical capacity, amplifier placement, and DSP strategy still determine how well the final system performs. Start a Build Consultation Call 864-334-6131 -
Hertz Audio S8 DSP Motorcycle/Powersports DSP
Vendor:HertzHertz S8 DSP — Clean Tuning Control for Harley Touring Builds The Hertz S8 DSP is built for riders who want repeatable tuning results: proper EQ shaping, correct crossover management, and stable routing so your system stays clean at speed. Shop Plug-and-Play DSPs Amplifier Installation Parts Start a Build Consultation THE REFERENCE STANDARD Fitment First. Then Performance. We confirm your integration path and channel plan before you order. What This DSP Does Adds the control your stock radio can’t: proper crossover points, EQ shaping, and tuning tools that keep speakers working together instead of competing for output. Best Use-Case on Harley Builds Touring systems that need clean staging and consistent clarity at speed Multi-speaker builds where correct crossover and time alignment matters Riders who want stable, repeatable tuning outcomes Included & Installation Notes Protected mounting and clean wiring paths matter as much as tuning Pairs best with correct amplification and a known speaker plan Use a consultation if you’re mapping fairing + lids + sub -
SaleRockford Fosgate DSR1 DSP
Vendor:Rockford FosgateRockford DSR1 — Proven DSP Control for Harley Touring Audio The Rockford Fosgate DSR1 is a proven DSP solution for riders who want clean signal control, correct crossover management, and stable tuning on real Harley touring builds. Shop Plug-and-Play DSPs Amplifier Installation Parts Start a Build Consultation THE REFERENCE STANDARD Fitment First. Then Performance. We’ll confirm the correct integration for your exact platform and goals before you order. Build it right the first time. Built for Harley Touring Installs Designed for Harley touring motorcycles using stock radios with the correct plug-and-play integration. Harley 2014–2023 stock radio: Plug-and-play ready Harley 2023.5+ (CVO / 2024+) stock radio: Plug-and-play ready We’ll confirm the correct integration for your exact platform and goals before finalizing your build. What This DSP Does The DSR1 gives you control your stock radio can’t—proper EQ shaping, correct crossover points, and balanced signal routing so your system stays loud, clean, and controlled at highway speed. Best Use-Case on Harley Builds Multi-speaker touring audio systems Riders who want stable, repeatable tuning Systems where correct crossover and time alignment make the difference Included & Installation Notes Installs cleanly in the fairing with protected mounting Requires proper power and grounding for best performance Pairs best with quality amplifiers and speakers Frequently Asked Questions Will this help with highway clarity? Yes—proper EQ and crossover control is what fixes “loud but messy” systems. Do I need this if I already have an amp? If you can’t tune correctly, yes. DSP is the missing control layer. Can GBS recommend settings? Yes—based on your exact bike, speakers, and amplifiers.Sale
