-
SaleCicada Audio DSP600.4D — 4‑Channel Amplifier with DSP
Vendor:Cicada AudioMotorcycle Amplifier + DSP Cicada Audio DSP600.4D — Compact 4-Channel Power with Built-In DSP Clean power + smart control. The DSP600.4D packs a 4-channel class-D amp and a flexible DSP into a compact, bike-ready chassis. Dial in PEQ, high/low-pass filters up to 20 kHz, and steep slopes (up to 48 dB) so your Harley-Davidson® or Indian® system stays loud and clear at highway speed. Why Riders Choose It Built-in DSP — 8-band PEQ, HPF/LPF to 20 kHz, slopes 6/12/18/24/48 dB. Serious output — up to 152×4 @ 2Ω or 300×2 bridged @ 4Ω (14.4V). Compact chassis — fits cleanly behind fairings or in bags. Bike-ready — designed for motorcycle use. Plays nice with stock radios — easy gain structure and integration. Shop Motorcycle Amplifiers Best With Efficient front speakers (6.5″/horns) at 2–4Ω Rear lids or mid-bass channels with tailored PEQ & HPF/LPF Bridged 4Ω pairs for higher output OFC wiring, proper fusing, and careful gain setup Tell us your bike and speakers — we’ll pre-map crossovers, slopes, and PEQ to your setup. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 70 × 4 / 92 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 115 × 4 / 152 × 4 Bridged @ 4Ω (12.5V / 14.4V) 218 × 2 / 300 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 DSP Crossovers HPF/LPF 0–20 kHz; slopes 6/12/18/24/48 dB DSP PEQ 8 bands; Q 0.05–20 Operating Voltage 8 – 16 V Current Draw (Music / Max) 40 A / 80 A Recommended Fuse 40 A Efficiency ~79% Dimensions (L × W × H) 8.875″ × 4.0″ × 1.4″ (225.4 × 103 × 36 mm) Specs from Cicada’s product page and manual. Always verify impedance/wiring before power-on. Frequently Asked Questions — Motorcycle Audio Can I power fronts and lids with one amp? Yes, many builds run all four channels. Use the DSP to set independent HPF/LPF and PEQ per pair for clean, balanced output. Will it work with my factory radio? Yes — it integrates cleanly. Set gains carefully and use the DSP to correct the factory curve. Add a dedicated DSP if you need time alignment. Can I bridge for more power? Yes — bridge pairs at 4Ω for up to 300 W × 2 (14.4V). Enable LPF when driving mid-bass or a small sub. What wiring and fuse do I need? Use OFC power/ground sized for the current draw, fused at the battery (40 A). Keep grounds short with solid chassis bonding. Is it weather resistant? It’s designed for motorcycles. Mount away from direct spray and protect cables from abrasion and heat. Garage Bagger Stereo Advantage Bike-specific DSP presets on request Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and phone support Need Help? Call us at (864) 334-6131 with your bike, speakers, and goals. We’ll map crossovers, EQ, and gains for your exact setup.Sale -
SaleCicada Audio FLX700.4 Motorcycle Amplifier
Vendor:Cicada AudioCicada Audio FLX700.4 4-Channel Motorcycle Amplifier The Cicada Audio FLX700.4 is a compact 4-channel motorcycle amplifier built for Harley-Davidson and Indian touring audio systems that need clean power, efficient output, and reliable highway-speed performance. With up to 175 watts x 4 at 2Ω, onboard crossover control, REM/DC turn-on, and a small motorcycle-ready chassis, the FLX700.4 is a strong fit for fairing speakers, saddlebag lid speakers, and clean amplified bagger audio builds. Cicada Amplifiers Motorcycle Amplifiers Shop Cicada Audio THE REFERENCE STANDARD Compact 4-Channel Power for Harley Audio Built for riders who need clean motorcycle amplifier power, compact installation, 2Ω/4Ω speaker support, and dependable output for real bagger audio systems. Start a Build Consultation Call 864-334-6131 Key Product Details Product Cicada Audio FLX700.4 4-Channel Motorcycle Amplifier Amplifier Type Compact 4-channel motorcycle amplifier Best For Harley-Davidson and Indian touring audio systems, fairing speakers, saddlebag lid speakers, coaxial speakers, and clean amplified motorcycle audio builds System Goal Clean power, stronger speaker output, better clarity, compact installation, and louder highway-speed performance Speaker Support 2Ω and 4Ω speaker systems, depending on final wiring and system design Install Focus Compact motorcycle amplifier layout for Harley-Davidson Touring, Road Glide, Street Glide, CVO, Indian, and custom bagger audio systems Always verify speaker impedance, wiring layout, fuse size, amplifier placement, gain structure, charging system capacity, and final system design before ordering or installing this amplifier. Built for Clean Harley-Davidson and Indian Audio Power The Cicada FLX700.4 is built for riders who want a clean, compact amplifier upgrade without overcomplicating the system. It gives Harley-Davidson and Indian touring motorcycles the power needed to run upgraded motorcycle-specific speakers with better clarity, stronger output, and more control than factory power alone. This amplifier is a strong choice for riders powering front fairing speakers, rear speakers, saddlebag lid speakers, or a balanced 4-channel motorcycle audio system. When matched with the right speakers, wiring, and tuning, the FLX700.4 helps the system stay cleaner and louder at speed. Power and Performance Specifications Channels 4 RMS Power @ 4Ω 125 watts x 4 channels RMS Power @ 2Ω 175 watts x 4 channels Bridged Power @ 4Ω 350 watts x 2 channels Crossovers HPF / LPF / FULL, 30Hz–300Hz Signal-to-Noise Ratio 95dB THD <0.1% Operating Voltage 8V–16V Fuse Rating 60A total, 2 x 30A Dimensions 11.5" x 5.1" x 1.8" Best Use for the FLX700.4 The FLX700.4 is best used in Harley-Davidson and Indian bagger audio builds that need compact 4-channel amplifier power for fairing speakers, rear speakers, saddlebag lid speakers, or efficient coaxial speaker systems. Designed Around Real Motorcycle Audio Motorcycle audio is different from car audio. Wind noise, road speed, speaker placement, electrical limits, wiring path, and mounting space all matter. This amplifier should be matched with the correct speaker load, clean wiring, and a proper tuning plan. Recommended System Planning To get the best performance from the Cicada FLX700.4, match it with efficient motorcycle-specific speakers, proper OFC power and ground wiring, correct battery-side fusing, clean signal input, and a real tuning plan. For Harley-Davidson Touring, Indian touring, and custom bagger audio systems, amplifier power should always be planned around the speakers, impedance, charging system, mounting location, and final sound goal. If you are unsure whether this amplifier is the right choice for your Road Glide, Street Glide, CVO, Road King, Indian, or custom motorcycle audio build, contact Garage Bagger Stereo before ordering. Related Cicada & Motorcycle Audio Paths Build the system around the correct amplifier, speakers, DSP, wiring, and installation parts. These related collections help match the FLX700.4 with the right Harley or Indian audio upgrade path. Shop Cicada motorcycle amplifiers for Harley-Davidson audio builds Shop motorcycle amplifiers for Harley bagger audio systems Shop Cicada Audio speakers, amplifiers, DSP, and bagger audio upgrades Shop motorcycle DSP for Harley-Davidson audio tuning Shop motorcycle amplifier installation parts Need Help Choosing the Right Cicada Amplifier? Need help matching the Cicada FLX700.4 to your speakers, bike, wiring, DSP, or complete Harley audio system? Call Garage Bagger Stereo or start a build consultation and we’ll help match the amplifier power, speaker layout, impedance, wiring, and tuning plan to your build. Call 864-334-6131 Start a Build ConsultationSale -
SaleCicada Audio FLX700.4PRO – 700W DSP Pro Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX700.4PRO — Compact 4-Channel Power with Built-In DSP Small chassis, big control. The FLX700.4PRO delivers clean power with an onboard 6-channel DSP (4 amplified + 2 pass-through), Bluetooth® streaming, and USB-C PC tuning. Designed for H-D® amp racks with multiple brackets, plus Molex® inputs for RCA or bike-specific termination. Why Riders Choose It Real output — 120×4 @ 4Ω, 175×4 @ 2Ω, or 350×2 bridged @ 4Ω (14.4V). 6-ch DSP onboard — tune crossovers/EQ on the bike; Bluetooth® audio built in. Bike-ready build — conformal-coated PCB in an extruded aluminum heatsink. Flexible turn-on — REM / DC / VOX with status & clipping LEDs. Premium I/O — 4 AWG power, 12 AWG speaker busbar-style terminals. Best With Front & rear pro speakers at 2–4Ω Bridged 4Ω pairs for lids/mid-bass OFC wiring, correct fusing, and solid grounds Factory radio or DSP signal — we’ll help map gains/filters Tell us your bike and speakers — we’ll pre-map crossovers and gains for highway-clear performance. Key Specifications RMS @ 4Ω (14.4V) 120 × 4 RMS @ 2Ω (14.4V) 175 × 4 Bridged @ 4Ω (14.4V) 350 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD + N (10% rated power) 0.1% @ 2Ω per ch SNR (A-wt) / Damping Factor 91 dB / 200 DSP / Tuning 6-ch DSP (4 amp + 2 pass), Bluetooth® audio, USB-C PC tuning Turn-On Modes REM / DC / VOX Operating Voltage 9 – 16 V Current Draw (Music / Max) 50 A / 80 A Recommended Fuse (Music) 50 A Efficiency ~80% Gain Range 0.2 – 12 V Dimensions (with brackets) 5.3″ × 4.9″ × 2.0″ (134 × 125 × 51 mm) Dimensions (chassis) 4.1″ × 4.9″ × 2.0″ (104 × 125 × 51 mm) Specs per Cicada Audio product page. Always verify wiring/impedance and set gains conservatively. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean OFC wiring and correct fusing On-bike DSP tuning for loud, clear highway sound Nationwide shipping & tech support Need Help? Call (864) 334-6131. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX1000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1000.4 — Compact 4-Channel Power for Bagger Audio Big output in a small chassis. The FLX1000.4 feeds your front + rear speakers real power from a palm-size, bike-ready amp. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a favorite for Harley-Davidson® and Indian® builds that need highway-clear sound without bulky gear. Why Riders Choose It Serious output — up to 254×4 @ 2Ω or 530×2 bridged @ 4Ω (14.4V). Compact chassis — 6.0″ × 4.9″ × 2.0″ fits behind fairings or in bags. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC options for easy integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring with correct fusing and clean grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 150 × 4 / 168 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 220 × 4 / 254 × 4 Bridged @ 4Ω (12.5V / 14.4V) 461 × 2 / 530 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) 60 A / 116 A Recommended Fuse (Music) 120 A Efficiency ~79% Dimensions (L × W × H) 6.0″ × 4.9″ × 2.0″ (152 × 124 × 51 mm) Specs from Cicada’s product page; retailer listings corroborate ratings and dimensions. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Can it run fronts and lids with one amp? Yes — many builds run four channels at 2–4Ω. Use HPF/LPF and proper gains for clean balance. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. Can I bridge it for more power? Yes — bridge pairs at 4Ω for up to ~530 W × 2 (14.4V). Use LPF for mid-bass or small sub duty. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (120 A music rec.). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX1400.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioCicada Audio FLX1400.4 4-Channel Motorcycle Amplifier The Cicada Audio FLX1400.4 is a high-output 4-channel motorcycle amplifier built for Harley-Davidson bagger audio systems that need serious clean power, strong speaker control, and reliable highway-speed output. This amplifier is a strong fit for riders powering fairing speakers, saddlebag lid speakers, midbass, or bridged speaker pairs in a loud, clean, motorcycle-ready audio build. Cicada Amplifiers Motorcycle Amplifiers Shop Cicada Audio THE REFERENCE STANDARD Clean 4-Channel Power for Harley Bagger Audio Built for riders who need compact motorcycle amplifier power, flexible crossover control, 2Ω/4Ω speaker support, and strong output for real Harley audio systems. Start a Build Consultation Call 864-334-6131 Key Product Details Product Cicada Audio FLX1400.4 4-Channel Motorcycle Amplifier Amplifier Type High-output 4-channel motorcycle amplifier Best For Harley-Davidson bagger audio, fairing speakers, saddlebag lid speakers, midbass, and amplified motorcycle audio systems System Goal Clean power, stronger output, better speaker control, and louder highway-speed performance Speaker Support 2Ω and 4Ω speaker systems, depending on final wiring and system design Install Focus Compact motorcycle amplifier layout for Harley-Davidson Touring and custom bagger audio builds Always verify speaker impedance, wiring layout, fuse size, amplifier placement, gain structure, and system design before ordering or installing this amplifier. Built for High-Output Harley Audio Systems The Cicada FLX1400.4 is built for Harley-Davidson and motorcycle audio systems where factory power is not enough. It gives riders the headroom needed to drive upgraded 6.5" speakers, 6x9 speakers, pro coaxials, midbass drivers, and bridged speaker pairs with cleaner output and better control. This amplifier is a strong choice when the goal is louder vocals, stronger midbass, reduced distortion, and better open-air performance at speed. In a properly planned Harley bagger audio system, the FLX1400.4 can support front and rear speaker layouts, fairing and lid speaker upgrades, or bridged power for more aggressive output. Power and Performance Specifications RMS Power @ 4Ω Approximately 200 watts x 4 channels at 14.4V RMS Power @ 2Ω Approximately 350 watts x 4 channels at 14.4V Bridged Power @ 4Ω Approximately 700 watts x 2 channels at 14.4V Frequency Response 20Hz–20kHz +/-3dB THD < 0.5% at 1kHz Signal-to-Noise Ratio Approximately 91dB A-weighted Damping Factor Approximately 200 Crossovers HPF / FULL / LPF, 30Hz–300Hz, 12dB/octave Turn-On Modes REM / DC turn-on support Operating Voltage 8V–16V Current Draw Approximately 70A music / 130A max Recommended Fuse Approximately 150A for music use Best Use for the FLX1400.4 The FLX1400.4 is best used in Harley-Davidson bagger audio builds that need strong 4-channel amplifier power for fairing speakers, saddlebag lid speakers, midbass, or bridged speaker layouts. It is built for riders who want more output without giving up control or clarity. Designed Around Real Motorcycle Audio Motorcycle audio is different from car audio. Wind noise, road speed, speaker placement, electrical load, and limited mounting space all matter. This amplifier belongs in systems where the speaker choice, wiring, fusing, and tuning plan are matched correctly. Recommended System Planning To get the best performance from the Cicada FLX1400.4, match it with the right speakers, proper OFC power and ground wiring, correct battery-side fusing, clean signal input, and a real tuning plan. For Harley-Davidson Touring and custom bagger audio systems, amplifier power should always be planned around the speakers, impedance, charging system, mounting location, and final sound goal. If you are unsure whether this amplifier is the right choice for your Road Glide, Street Glide, CVO, Road King, Indian, or custom motorcycle audio build, contact Garage Bagger Stereo before ordering. Related Cicada & Motorcycle Audio Paths Build the system around the correct amplifier, speakers, DSP, wiring, and installation parts. These related collections help match the FLX1400.4 with the right Harley audio upgrade path. Shop Cicada motorcycle amplifiers for Harley-Davidson audio builds Shop motorcycle amplifiers for Harley bagger audio systems Shop Cicada Audio speakers, amplifiers, DSP, and bagger audio upgrades Shop motorcycle DSP for Harley-Davidson audio tuning Shop motorcycle amplifier installation parts Need Help Choosing the Right Cicada Amplifier? Need help matching the Cicada FLX1400.4 to your speakers, bike, wiring, DSP, or complete Harley audio system? Call Garage Bagger Stereo or start a build consultation and we’ll help match the amplifier power, speaker layout, impedance, and tuning plan to your build. Call 864-334-6131 Start a Build ConsultationSale -
SaleCicada Audio FLX2000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioCicada Audio FLX2000.4 2000W 4-Channel Motorcycle Amplifier The Cicada Audio FLX2000.4 is a compact high-output 4-channel motorcycle amplifier built for Harley-Davidson bagger audio systems that need serious power, clean control, and highway-speed volume. With strong output at 2Ω and 4Ω, bridgeable power, onboard crossover control, and motorcycle-ready construction, the FLX2000.4 is built for riders who want more speaker authority without adding oversized amplifier hardware. Cicada Amplifiers Motorcycle Amplifiers Shop Cicada Audio THE REFERENCE STANDARD Big 4-Channel Power for Harley Bagger Audio Built for high-output Harley audio systems that need compact amplifier power, clean tuning control, 2Ω/4Ω speaker support, and serious open-air performance. Start a Build Consultation Call 864-334-6131 Key Product Details Product Cicada Audio FLX2000.4 2000W 4-Channel Motorcycle Amplifier Amplifier Type High-output 4-channel motorcycle amplifier Best For Harley-Davidson bagger audio, fairing speakers, saddlebag lid speakers, midbass, bridged speaker pairs, and high-output amplified motorcycle systems System Goal More power, stronger speaker control, louder open-air output, cleaner tuning, and better highway-speed performance Speaker Support 2Ω and 4Ω speaker systems, depending on final wiring and system design Install Focus Compact motorcycle amplifier layout for Harley-Davidson Touring, Road Glide, Street Glide, CVO, Indian, and custom bagger audio builds Always verify speaker impedance, wiring layout, fuse size, amplifier placement, gain structure, charging system capacity, and final system design before ordering or installing this amplifier. Built for Serious Harley-Davidson Audio Power The Cicada FLX2000.4 is made for riders who need more than basic motorcycle amplifier power. It is designed to drive upgraded 6.5" speakers, 6x9 speakers, pro coaxials, saddlebag lid speakers, midbass drivers, or bridged 4Ω speaker pairs with serious output and control. In a properly planned Harley-Davidson bagger audio system, the FLX2000.4 can support aggressive front and rear speaker layouts, bridged midbass power, or full custom speaker systems where clean volume and highway-speed performance are the priority. Power and Performance Specifications RMS Power @ 4Ω 275 watts x 4 channels at 12.5V / 331 watts x 4 channels at 14.4V RMS Power @ 2Ω 450 watts x 4 channels at 12.5V / 542 watts x 4 channels at 14.4V Bridged Power @ 4Ω 866 watts x 2 channels at 12.5V / 1044 watts x 2 channels at 14.4V Frequency Response 20Hz–20kHz +/-3dB THD < 0.5% at 1kHz Signal-to-Noise Ratio 91dB A-weighted Damping Factor 200 Crossovers HPF / FULL / LPF, 30Hz–300Hz, 12dB/octave Turn-On Modes REM / DC turn-on support Operating Voltage 8V–16V Current Draw 60A music / 240A max Recommended Fuse 120A for music use Efficiency Approximately 79% Gain Range 0.2V–12V Dimensions 8.6" x 4.9" x 2.0" / 218mm x 124mm x 51mm Best Use for the FLX2000.4 The FLX2000.4 is best used in Harley-Davidson and custom bagger audio builds that need strong 4-channel amplifier power for fairing speakers, saddlebag lid speakers, midbass, or bridged speaker pairs. Designed Around Real Motorcycle Audio Motorcycle audio is different from car audio. Wind noise, road speed, speaker placement, electrical load, limited mounting space, and heat management all matter. This amplifier belongs in systems where the speakers, wiring, fusing, and tuning plan are matched correctly. Recommended System Planning To get the best performance from the Cicada FLX2000.4, match it with the right speakers, proper OFC power and ground wiring, correct battery-side fusing, clean signal input, and a real tuning plan. For Harley-Davidson Touring and custom bagger audio systems, amplifier power should always be planned around the speakers, impedance, charging system, mounting location, and final sound goal. If you are unsure whether this amplifier is the right choice for your Road Glide, Street Glide, CVO, Road King, Indian, or custom motorcycle audio build, contact Garage Bagger Stereo before ordering. Related Cicada & Motorcycle Audio Paths Build the system around the correct amplifier, speakers, DSP, wiring, and installation parts. These related collections help match the FLX2000.4 with the right Harley audio upgrade path. Shop Cicada motorcycle amplifiers for Harley-Davidson audio builds Shop motorcycle amplifiers for Harley bagger audio systems Shop Cicada Audio speakers, amplifiers, DSP, and bagger audio upgrades Shop motorcycle DSP for Harley-Davidson audio tuning Shop motorcycle amplifier installation parts Need Help Choosing the Right Cicada Amplifier? Need help matching the Cicada FLX2000.4 to your speakers, bike, wiring, DSP, or complete Harley audio system? Call Garage Bagger Stereo or start a build consultation and we’ll help match the amplifier power, speaker layout, impedance, wiring, and tuning plan to your build. Call 864-334-6131 Start a Build ConsultationSale -
SaleCicada Audio FLX1600.1 — Mono Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier — Mono Cicada Audio FLX1600.1 — High-Output Mono Power for Bagger Audio One channel, no compromise. The FLX1600.1 is a mono full-range workhorse for high-output lids, mid-bass, or a compact sub. It packs serious wattage into a compact, bike-ready chassis with HPF/LPF control and clean integration on Harley-Davidson® and Indian® touring platforms. Why Riders Choose It Serious output — up to 1600 × 1 @ 2Ω (14.4V). Compact chassis — 8.6″ × 4.9″ × 2.0″ tucks behind fairings/bags. Bike-ready — element-ready design for motorcycle use. Flexible turn-on — REM / DC integration. On-board crossovers — HPF 10–80 Hz; LPF 80 Hz–20 kHz, 12 dB/oct. Shop Motorcycle Amplifiers Best With High-output lids or mid-bass at 2–4Ω Compact 4Ω subwoofer (enable LPF) OFC wiring & correct fusing; careful gain setup Factory radio or DSP front-end Tell us your bike and speakers — we’ll map crossovers, slopes, and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 670 × 1 / 950 × 1 RMS Power @ 2Ω (12.5V / 14.4V) 1250 × 1 / 1600 × 1 Frequency Response 10 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 86 dB / 200 Crossovers HPF 10–80 Hz; LPF 80 Hz–20 kHz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 9 – 16 V Current Draw (Music / Max) 70 A / 140 A Recommended Fuse (Music) 100 A Efficiency ~80% Gain Range 0.2 – 12 V Dimensions (L × W × H) 8.6″ × 4.9″ × 2.0″ (218 × 124 × 51 mm) Specs from Cicada’s product page; multiple dealers corroborate power ratings and crossover ranges. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Is this for subs or mids? Both. It’s a mono full-range design. Use HPF for mid-bass/lids or LPF for a compact sub. We’ll help you choose the right filter points. Will it work with my factory radio? Yes — use DC or REM turn-on and set gains carefully. Add DSP if you need advanced EQ or time alignment. What wiring and fuse should I use? Use OFC wire sized for current draw and fuse at the battery (100 A music). Keep grounds short with solid chassis bonding. Is it motorcycle-ready? Yes — element-ready construction. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX2500.1 — Mono Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier — Mono Cicada Audio FLX2500.1 — High-Output Mono Power for Bagger Audio One channel, maximum punch. The FLX2500.1 is a mono full-range workhorse for high-output lids, mid-bass, or a compact sub. It packs big wattage into a compact, bike-ready chassis, with HPF/LPF control and clean integration on Harley-Davidson® and Indian® touring platforms. Why Riders Choose It Serious output — up to 2500 × 1 @ 2Ω (14.4V). Compact chassis — 9.2″ × 4.9″ × 2.0″ tucks behind fairings/bags. Bike-ready — element-ready design for motorcycles. Flexible turn-on — REM / DC integration. On-board crossovers — HPF 10–80 Hz; LPF 80 Hz–20 kHz, 12 dB/oct. Cicada recommends a lithium battery upgrade and 2 AWG power wire for this model. Best With High-output lids or mid-bass at 2–4Ω Compact 4Ω subwoofer (enable LPF) OFC wiring & correct fusing; careful gain setup Factory radio or DSP front-end Tell us your bike and speakers — we’ll map crossovers, slopes, and gains for loud, clean highway performance. Key Specifications RMS Power @ 2Ω (14.4V) 2500 × 1 Frequency Response 10 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% @ 10% rated power) SNR (A-wt) / Damping Factor 86 dB / 200 Crossovers HPF 10–80 Hz; LPF 80 Hz–20 kHz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 9 – 16 V Current Draw (Music / Max) 80 A / 260 A Recommended Fuse (Music) 150 A Total Efficiency ~80% Gain Range 0.2 – 12 V Dimensions (L × W × H) 9.2″ × 4.9″ × 2.0″ (234 × 124 × 51 mm) Specs pulled from Cicada’s official page; multiple dealers corroborate power, dimensions, and fuse guidance. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Is this for subs or mids? Both. It’s a mono full-range design. Use HPF for mid-bass/lids or LPF for a compact sub. We’ll help you choose the right filter points. Will it work with my factory radio? Yes — use DC or REM turn-on and set gains carefully. Add DSP if you need advanced EQ or time alignment. What wiring and battery should I use? Run 2 AWG power, fuse at the battery (150 A music), and use a lithium battery upgrade as recommended by Cicada. Is it motorcycle-ready? Yes — element-ready construction. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio BFA5000.1 – Monoblock Class D Amplifier 5000W
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio BFA5000.1 — 5000W Monoblock Class D Serious bass power for serious builds. The BFA5000.1 drives demanding sub/enclosure setups with premium busbar I/O, 1/0 AWG power, and Molex® inputs for RCA or H-D® terminations. Conformal-coated PCB, extruded aluminum heatsink, and status/clipping LEDs keep it bike-ready and trackable. Why Riders Choose It Huge output — 3000W @ 4Ω or 5000W @ 2Ω (14.4V). Compact & robust — built for motorcycle environments. Smart controls — LPF and Subsonic filters with 12 dB/oct slopes. Premium connections — 1/0 AWG power, 12 AWG speaker busbar terminals. Dimensions (L x W x H): 11.7" x 7.0" x 2.6" 2-year warranty — confidence for high-output systems. Not intended for a standard amp rack in the fairing Best With High-efficiency subs or mid-bass enclosures Proper electrical upgrades (AGM/LiFePO₄, big 3) OFC power/ground and correct fusing DSP for system integration and limiters We’ll help set gain structure and filters to keep things loud and safe. Key Specifications RMS @ 4Ω (14.4V) 3000 × 1 RMS @ 2Ω (14.4V) 5000 × 1 Frequency Response 20 Hz – 250 Hz (±3 dB) SNR (A-wt) / Damping Factor 86 dB / 200 Crossovers LPF 20–250 Hz; Subsonic 20–50 Hz; 12 dB/oct Operating Voltage 9 – 16 V Current Draw (Music / Max) 200 A / 450 A Recommended Fuse (Music) 200 A Connectivity Molex® inputs; 1/0 AWG power; 12 AWG speaker busbar Specs per Cicada Audio product page. Verify wiring/impedance and ensure electrical upgrades for sustained output. Garage Bagger Stereo Advantage Bike-specific mounting & heat management OFC wiring, correct fusing, clean routing On-bike tuning and limiter setup Nationwide shipping & support Need Help? Call (864) 334-6131. We’ll spec wiring, fusing, and filters for your exact build.Sale -
SaleCicada Audio FLX1400.4PRO Amplifier 350W x 4CH w/ DSP
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1400.4PRO — High-Output 4-Channel Amplifier with Built-In DSP Serious power with full tuning control. The Cicada Audio FLX1400.4PRO is built for high-output motorcycle audio systems that need strong 4-channel power, clean signal control, and flexible system tuning in one compact amplifier. With built-in DSP, strong 2Ω output, and motorcycle-ready design, this amp is ideal for Harley-Davidson®, Indian®, and custom bagger audio builds that need loud, clean performance at highway speed. Why Riders Choose It Built-in DSP control — tune EQ, crossover points, output levels, and system response with more precision. High-output 4-channel power — ideal for fairing speakers, lowers, lids, pods, and midrange upgrades. Strong 2Ω performance — built for demanding motorcycle speaker setups. Compact motorcycle-friendly chassis — easier to fit in tight bagger installations. Clean system integration — designed for riders who want power and tuning flexibility in one amplifier. Shop Motorcycle Amplifiers Best With High-output Harley-Davidson® and Indian® audio systems Front fairing speakers, saddlebag lids, lowers, and speaker pods 2Ω or 4Ω motorcycle speaker setups Systems needing built-in DSP control without adding a separate processor OFC wiring, correct fusing, and clean amplifier grounding Tell us your bike, speakers, and system layout — we’ll help match wiring, gain structure, crossover points, and tuning strategy. Key Specifications Amplifier Type 4-Channel Motorcycle Amplifier with Built-In DSP RMS Power @ 4Ω High-output 4-channel power for motorcycle speaker systems RMS Power @ 2Ω Built for strong 2Ω speaker output DSP Control Built-in digital signal processing for system tuning System Use Fairing speakers, lids, lowers, pods, and custom bagger audio builds Recommended Wiring OFC power and ground wiring with proper battery-side fuse protection Application Harley-Davidson®, Indian®, motorcycle, powersports, and custom audio systems Design Focus High-output power, compact fitment, and clean tuning control Always verify impedance, wiring, fuse size, speaker load, and final tuning for your exact setup. Built-In DSP Advantage The FLX1400.4PRO is more than just a power amplifier. The built-in DSP gives you control over how the system sounds, how each channel is filtered, and how the output is balanced across the bike. This is especially important on motorcycle systems where speaker placement, wind noise, road noise, and open-air listening conditions make proper tuning critical. Better speaker control through proper crossover setup Cleaner output by matching gain and signal levels correctly More flexible tuning for different speaker locations Improved clarity at highway speed when properly tuned Frequently Asked Questions — Motorcycle Audio Is the FLX1400.4PRO good for Harley bagger audio? Yes. This amplifier is a strong choice for Harley-Davidson® touring audio builds, especially systems using fairing speakers, saddlebag lid speakers, lowers, or speaker pods. Why choose the PRO version with DSP? The built-in DSP gives you more control over the final sound. Instead of relying only on basic amplifier adjustments, the system can be tuned for crossover points, output balance, and overall response. Can this amp run multiple speaker locations? Yes. A 4-channel layout is commonly used for front and rear speaker setups, fairing and lid speakers, or other multi-speaker motorcycle audio layouts. Always verify final impedance before wiring. Do I still need proper wiring and fusing? Yes. High-output motorcycle amplifiers need clean OFC power and ground wiring, proper fuse protection near the battery, and secure connections to perform safely and reliably. Garage Bagger Stereo Advantage Bike-specific amplifier placement and heat management Clean, serviceable OFC wiring and correct fuse protection DSP setup for loud, clear highway performance System matching for Harley-Davidson®, Indian®, and custom bagger builds Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike, speakers, and system goals. We’ll help match the amplifier, wiring, gain structure, and DSP setup for your exact build.Sale -
SaleCicada Audio 24HDAR-RG Amplifier Rack for 2024+ Road Glide
Vendor:Cicada Audio2024+ ROAD GLIDE AMPLIFIER RACK Cicada Audio 24HDAR-RG Amplifier Rack for 2024+ Road Glide The Cicada Audio 24HDAR-RG provides a clean, bike-specific mounting foundation for Cicada FLX-style amplifiers in 2024 and newer Harley-Davidson Road Glide models. Its black-anodized aluminum construction, OEM mounting-point fitment, and predrilled amplifier patterns help keep the installation secure, organized, and serviceable. Check Fitment What’s Included Purpose-Built for Road Glide Audio Designed for 2024+ Harley-Davidson Road Glide Uses OEM amplifier mounting locations Predrilled for Cicada FLX-style amplifiers Black-anodized aluminum construction Mounting hardware included Amplifier sold separately Cicada 24HDAR-RG Amplifier Rack Overview Adding an amplifier to a newer Road Glide requires more than finding an open space inside the fairing. The amplifier needs a secure mounting surface that supports clean wiring, proper service access, and reliable placement. The Cicada Audio 24HDAR-RG is designed around the factory amplifier mounting locations on 2024 and newer Harley-Davidson Road Glide models. Multiple predrilled mounting patterns support Cicada FLX-style amplifiers without requiring the installer to begin with a blank, universal plate. Why Riders and Installers Choose It Road Glide-Specific Fitment Designed around the OEM amplifier mounting locations found on 2024 and newer Harley-Davidson Road Glide models. Predrilled Amplifier Patterns Predrilled mounting locations simplify installation of compatible Cicada FLX-style amplifiers. Aluminum Construction The aluminum rack provides a rigid mounting foundation without the unnecessary bulk of a heavy universal platform. Black-Anodized Finish The black-anodized surface provides a clean finished appearance suitable for a professional motorcycle audio installation. Cleaner Wire Management A dedicated amplifier platform makes it easier to plan power, signal, speaker, remote, and ground-wire routing. Serviceable Installation Secure amplifier placement helps keep the audio system easier to inspect, tune, maintain, and service. Fitment and Compatibility Product Model Cicada Audio 24HDAR-RG Product Type Motorcycle amplifier mounting rack Motorcycle Fitment 2024 and newer Harley-Davidson Road Glide models Mounting Method Uses OEM amplifier mounting locations Amplifier Compatibility Designed for Cicada FLX-style amplifiers Amplifier Mounting Predrilled amplifier mounting patterns Construction Aluminum Finish Black anodized Amplifier Included? No. Amplifier is sold separately. What’s Included Cicada Audio 24HDAR-RG aluminum amplifier rack Required rack mounting hardware Cable-management ties supplied with the mounting package Amplifier not included: This listing is for the amplifier rack and supplied installation hardware. Cicada FLX amplifiers, wiring, fuses, DSP equipment, and other audio-system components are sold separately unless specifically stated. Designed for Cicada FLX Amplifier Builds The 24HDAR-RG is designed to support Cicada FLX-style amplifiers using the rack’s predrilled mounting locations. Your final amplifier choice should be based on speaker impedance, channel count, RMS power needs, system layout, charging capacity, and available fairing clearance. Shop Motorcycle Amplifiers Shop Cicada Audio Important Installation Notes Confirm the exact motorcycle year, model, trim, and factory audio configuration before ordering. Test-fit the rack and amplifier before completing the power, ground, signal, and speaker wiring. Verify amplifier dimensions, connector clearance, fairing clearance, and ventilation before final assembly. Use properly sized power and ground wire with correct battery-mounted fuse protection. Keep power wiring separated from low-level signal wiring whenever the installation layout allows. Secure all wiring to prevent contact with sharp edges, steering components, heat sources, and moving parts. Professional motorcycle audio installation is recommended. Garage Bagger Stereo Advantage Road Glide-specific amplifier placement guidance Cicada FLX amplifier and speaker-system matching Power-wire, fuse, grounding, and signal-routing recommendations DSP setup and motorcycle audio tuning support Professional installation available in Taylors, South Carolina Related Motorcycle Audio Categories Cicada and Road Glide Audio Cicada Motorcycle Audio 2023.5+ and 2024+ Harley Plug-and-Play Kits Motorcycle Speakers Amplifiers and Installation Parts Motorcycle Amplifiers Motorcycle Amplifier Installation Parts Motorcycle DSP and Signal Integration Professional Installation Motorcycle Audio Installation in Taylors, SC Request a Custom Audio Build Call Garage Bagger Stereo Cicada 24HDAR-RG FAQ What motorcycle does the Cicada 24HDAR-RG fit? It is designed for 2024 and newer Harley-Davidson Road Glide models. Verify the exact motorcycle and factory audio configuration before ordering. Does the rack use factory mounting locations? Yes. The rack is designed to attach using the motorcycle’s OEM amplifier mounting locations. Which amplifiers fit the 24HDAR-RG? The rack is designed for Cicada FLX-style amplifiers. Final amplifier dimensions, connector clearance, wiring space, and installation layout should still be verified. Are the amplifier holes predrilled? Yes. The rack includes predrilled mounting patterns for compatible Cicada FLX-style amplifier layouts. Is the amplifier included? No. This listing is for the amplifier rack and supplied mounting hardware. The amplifier is sold separately. Is mounting hardware included? Yes. Rack mounting hardware is included. Need Help Planning Your Road Glide Amplifier Install? Call Garage Bagger Stereo with your Road Glide year, factory audio system, planned Cicada amplifier, speakers, and DSP configuration. We’ll help confirm the rack, amplifier layout, wiring, fuse protection, and supporting equipment for your build. Call 864-334-6131 Ask GBS for HelpSale -
SaleCicada Audio 24HDAR-SG Amplifier Rack for 2024+ Street Glide
Vendor:Cicada Audio2024+ STREET GLIDE AMPLIFIER RACK Cicada Audio 24HDAR-SG Amplifier Rack for 2024+ Street Glide The Cicada Audio 24HDAR-SG provides a clean, bike-specific mounting foundation for Cicada FLX-style amplifiers in 2024 and newer Harley-Davidson Street Glide models. Its black-anodized aluminum construction, OEM mounting-point fitment, and predrilled amplifier holes help keep the installation secure, organized, and serviceable. Check Fitment What’s Included Purpose-Built for Street Glide Audio Designed for 2024+ Harley-Davidson Street Glide Uses OEM amplifier mounting locations Predrilled for Cicada FLX-style amplifiers Black-anodized aluminum construction Mounting hardware included Amplifier sold separately Cicada 24HDAR-SG Amplifier Rack Overview Adding an amplifier to a newer Street Glide requires more than finding open space inside the fairing. The amplifier needs a secure mounting surface that supports clean wiring, proper service access, and reliable placement. The Cicada Audio 24HDAR-SG is designed around the OEM amplifier mounting locations on 2024 and newer Harley-Davidson Street Glide models. Predrilled amplifier holes support compatible Cicada FLX-style amplifiers without requiring the installer to begin with a blank, universal mounting plate. Why Riders and Installers Choose It Street Glide-Specific Fitment Designed around the OEM amplifier mounting locations found on 2024 and newer Harley-Davidson Street Glide models. Predrilled Amplifier Holes Predrilled mounting locations simplify installation of compatible Cicada FLX-style amplifiers. Aluminum Construction The aluminum rack provides a rigid mounting foundation without the unnecessary bulk of a heavy universal platform. Black-Anodized Finish The black-anodized surface provides a clean finished appearance suited for a professional motorcycle audio installation. Cleaner Wire Management A dedicated amplifier platform makes it easier to plan power, signal, speaker, remote, and ground-wire routing. Serviceable Installation Secure amplifier placement helps keep the audio system easier to inspect, tune, maintain, and service. Fitment and Compatibility Product Model Cicada Audio 24HDAR-SG Product Type Motorcycle amplifier mounting rack Motorcycle Fitment 2024 and newer Harley-Davidson Street Glide models Mounting Method Uses OEM amplifier mounting locations Amplifier Compatibility Designed for Cicada FLX-style amplifiers Amplifier Mounting Predrilled amplifier mounting holes Construction Aluminum Finish Black anodized Amplifier Included? No. Amplifier is sold separately. Verify before ordering: Confirm the exact motorcycle year, model, trim, factory audio configuration, amplifier dimensions, connector clearance, and available fairing space before installation. What’s Included Cicada Audio 24HDAR-SG aluminum amplifier rack Required rack mounting hardware Amplifier not included: This listing is for the amplifier rack and supplied mounting hardware. Cicada FLX amplifiers, power wiring, fuse protection, signal wiring, DSP equipment, speakers, and other audio-system components are sold separately unless specifically stated. Designed for Cicada FLX Amplifier Builds The 24HDAR-SG is designed to support Cicada FLX-style amplifiers using the rack’s predrilled mounting holes. Your final amplifier choice should be based on speaker impedance, channel count, RMS power requirements, system layout, charging capacity, and available fairing clearance. Shop Motorcycle Amplifiers Shop Cicada Audio Important Installation Notes Confirm the exact motorcycle year, model, trim, and factory audio configuration before ordering. Test-fit the rack and amplifier before completing the power, ground, signal, remote, and speaker wiring. Verify amplifier dimensions, connector clearance, fairing clearance, and ventilation before final assembly. Use properly sized power and ground wire with correct battery-mounted fuse protection. Keep power wiring separated from low-level signal wiring whenever the installation layout allows. Secure all wiring to prevent contact with sharp edges, steering components, heat sources, and moving parts. Professional motorcycle audio installation is recommended. Garage Bagger Stereo Advantage Street Glide-specific amplifier placement guidance Cicada FLX amplifier and speaker-system matching Power-wire, fuse, grounding, and signal-routing recommendations DSP setup and motorcycle audio tuning support Professional installation available in Taylors, South Carolina Related Motorcycle Audio Categories Cicada and Street Glide Audio Cicada Motorcycle Audio 2023.5+ and 2024+ Harley Plug-and-Play Kits Motorcycle Speakers Amplifiers and Installation Parts Motorcycle Amplifiers Motorcycle Amplifier Installation Parts Motorcycle DSP and Signal Integration Professional Installation Motorcycle Audio Installation in Taylors, SC Request a Custom Audio Build Call Garage Bagger Stereo Cicada 24HDAR-SG FAQ What motorcycle does the Cicada 24HDAR-SG fit? It is designed for 2024 and newer Harley-Davidson Street Glide models. Verify the exact motorcycle and factory audio configuration before ordering. Does the rack use factory mounting locations? Yes. The rack is designed to attach using the motorcycle’s OEM amplifier mounting locations. Which amplifiers fit the 24HDAR-SG? The rack is designed for Cicada FLX-style amplifiers. Final amplifier dimensions, connector clearance, wiring space, and installation layout should still be verified. Are the amplifier holes predrilled? Yes. The rack includes predrilled mounting holes for compatible Cicada FLX-style amplifier layouts. Is the amplifier included? No. This listing is for the amplifier rack and supplied mounting hardware. The amplifier is sold separately. Is mounting hardware included? Yes. Rack mounting hardware is included. Need Help Planning Your Street Glide Amplifier Install? Call Garage Bagger Stereo with your Street Glide year, factory audio system, planned Cicada amplifier, speakers, and DSP configuration. We’ll help confirm the rack, amplifier layout, wiring, fuse protection, and supporting equipment for your build. Call 864-334-6131 Ask GBS for HelpSale
-
Sale
Cicada Audio DSP600.4D — 4‑Channel Amplifier with DSP
Vendor:Cicada AudioMotorcycle Amplifier + DSP Cicada Audio DSP600.4D — Compact 4-Channel Power with Built-In DSP Clean power + smart control. The DSP600.4D packs a 4-channel class-D amp and a flexible DSP into a compact, bike-ready chassis. Dial in PEQ, high/low-pass filters up to 20 kHz, and steep slopes (up to 48 dB) so your Harley-Davidson® or Indian® system stays loud and clear at highway speed. Why Riders Choose It Built-in DSP — 8-band PEQ, HPF/LPF to 20 kHz, slopes 6/12/18/24/48 dB. Serious output — up to 152×4 @ 2Ω or 300×2 bridged @ 4Ω (14.4V). Compact chassis — fits cleanly behind fairings or in bags. Bike-ready — designed for motorcycle use. Plays nice with stock radios — easy gain structure and integration. Shop Motorcycle Amplifiers Best With Efficient front speakers (6.5″/horns) at 2–4Ω Rear lids or mid-bass channels with tailored PEQ & HPF/LPF Bridged 4Ω pairs for higher output OFC wiring, proper fusing, and careful gain setup Tell us your bike and speakers — we’ll pre-map crossovers, slopes, and PEQ to your setup. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 70 × 4 / 92 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 115 × 4 / 152 × 4 Bridged @ 4Ω (12.5V / 14.4V) 218 × 2 / 300 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 DSP Crossovers HPF/LPF 0–20 kHz; slopes 6/12/18/24/48 dB DSP PEQ 8 bands; Q 0.05–20 Operating Voltage 8 – 16 V Current Draw (Music / Max) 40 A / 80 A Recommended Fuse 40 A Efficiency ~79% Dimensions (L × W × H) 8.875″ × 4.0″ × 1.4″ (225.4 × 103 × 36 mm) Specs from Cicada’s product page and manual. Always verify impedance/wiring before power-on. Frequently Asked Questions — Motorcycle Audio Can I power fronts and lids with one amp? Yes, many builds run all four channels. Use the DSP to set independent HPF/LPF and PEQ per pair for clean, balanced output. Will it work with my factory radio? Yes — it integrates cleanly. Set gains carefully and use the DSP to correct the factory curve. Add a dedicated DSP if you need time alignment. Can I bridge for more power? Yes — bridge pairs at 4Ω for up to 300 W × 2 (14.4V). Enable LPF when driving mid-bass or a small sub. What wiring and fuse do I need? Use OFC power/ground sized for the current draw, fused at the battery (40 A). Keep grounds short with solid chassis bonding. Is it weather resistant? It’s designed for motorcycles. Mount away from direct spray and protect cables from abrasion and heat. Garage Bagger Stereo Advantage Bike-specific DSP presets on request Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and phone support Need Help? Call us at (864) 334-6131 with your bike, speakers, and goals. We’ll map crossovers, EQ, and gains for your exact setup.Sale -
Sale
Cicada Audio FLX700.4 Motorcycle Amplifier
Vendor:Cicada AudioCicada Audio FLX700.4 4-Channel Motorcycle Amplifier The Cicada Audio FLX700.4 is a compact 4-channel motorcycle amplifier built for Harley-Davidson and Indian touring audio systems that need clean power, efficient output, and reliable highway-speed performance. With up to 175 watts x 4 at 2Ω, onboard crossover control, REM/DC turn-on, and a small motorcycle-ready chassis, the FLX700.4 is a strong fit for fairing speakers, saddlebag lid speakers, and clean amplified bagger audio builds. Cicada Amplifiers Motorcycle Amplifiers Shop Cicada Audio THE REFERENCE STANDARD Compact 4-Channel Power for Harley Audio Built for riders who need clean motorcycle amplifier power, compact installation, 2Ω/4Ω speaker support, and dependable output for real bagger audio systems. Start a Build Consultation Call 864-334-6131 Key Product Details Product Cicada Audio FLX700.4 4-Channel Motorcycle Amplifier Amplifier Type Compact 4-channel motorcycle amplifier Best For Harley-Davidson and Indian touring audio systems, fairing speakers, saddlebag lid speakers, coaxial speakers, and clean amplified motorcycle audio builds System Goal Clean power, stronger speaker output, better clarity, compact installation, and louder highway-speed performance Speaker Support 2Ω and 4Ω speaker systems, depending on final wiring and system design Install Focus Compact motorcycle amplifier layout for Harley-Davidson Touring, Road Glide, Street Glide, CVO, Indian, and custom bagger audio systems Always verify speaker impedance, wiring layout, fuse size, amplifier placement, gain structure, charging system capacity, and final system design before ordering or installing this amplifier. Built for Clean Harley-Davidson and Indian Audio Power The Cicada FLX700.4 is built for riders who want a clean, compact amplifier upgrade without overcomplicating the system. It gives Harley-Davidson and Indian touring motorcycles the power needed to run upgraded motorcycle-specific speakers with better clarity, stronger output, and more control than factory power alone. This amplifier is a strong choice for riders powering front fairing speakers, rear speakers, saddlebag lid speakers, or a balanced 4-channel motorcycle audio system. When matched with the right speakers, wiring, and tuning, the FLX700.4 helps the system stay cleaner and louder at speed. Power and Performance Specifications Channels 4 RMS Power @ 4Ω 125 watts x 4 channels RMS Power @ 2Ω 175 watts x 4 channels Bridged Power @ 4Ω 350 watts x 2 channels Crossovers HPF / LPF / FULL, 30Hz–300Hz Signal-to-Noise Ratio 95dB THD <0.1% Operating Voltage 8V–16V Fuse Rating 60A total, 2 x 30A Dimensions 11.5" x 5.1" x 1.8" Best Use for the FLX700.4 The FLX700.4 is best used in Harley-Davidson and Indian bagger audio builds that need compact 4-channel amplifier power for fairing speakers, rear speakers, saddlebag lid speakers, or efficient coaxial speaker systems. Designed Around Real Motorcycle Audio Motorcycle audio is different from car audio. Wind noise, road speed, speaker placement, electrical limits, wiring path, and mounting space all matter. This amplifier should be matched with the correct speaker load, clean wiring, and a proper tuning plan. Recommended System Planning To get the best performance from the Cicada FLX700.4, match it with efficient motorcycle-specific speakers, proper OFC power and ground wiring, correct battery-side fusing, clean signal input, and a real tuning plan. For Harley-Davidson Touring, Indian touring, and custom bagger audio systems, amplifier power should always be planned around the speakers, impedance, charging system, mounting location, and final sound goal. If you are unsure whether this amplifier is the right choice for your Road Glide, Street Glide, CVO, Road King, Indian, or custom motorcycle audio build, contact Garage Bagger Stereo before ordering. Related Cicada & Motorcycle Audio Paths Build the system around the correct amplifier, speakers, DSP, wiring, and installation parts. These related collections help match the FLX700.4 with the right Harley or Indian audio upgrade path. Shop Cicada motorcycle amplifiers for Harley-Davidson audio builds Shop motorcycle amplifiers for Harley bagger audio systems Shop Cicada Audio speakers, amplifiers, DSP, and bagger audio upgrades Shop motorcycle DSP for Harley-Davidson audio tuning Shop motorcycle amplifier installation parts Need Help Choosing the Right Cicada Amplifier? Need help matching the Cicada FLX700.4 to your speakers, bike, wiring, DSP, or complete Harley audio system? Call Garage Bagger Stereo or start a build consultation and we’ll help match the amplifier power, speaker layout, impedance, wiring, and tuning plan to your build. Call 864-334-6131 Start a Build ConsultationSale -
Sale
Cicada Audio FLX700.4PRO – 700W DSP Pro Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX700.4PRO — Compact 4-Channel Power with Built-In DSP Small chassis, big control. The FLX700.4PRO delivers clean power with an onboard 6-channel DSP (4 amplified + 2 pass-through), Bluetooth® streaming, and USB-C PC tuning. Designed for H-D® amp racks with multiple brackets, plus Molex® inputs for RCA or bike-specific termination. Why Riders Choose It Real output — 120×4 @ 4Ω, 175×4 @ 2Ω, or 350×2 bridged @ 4Ω (14.4V). 6-ch DSP onboard — tune crossovers/EQ on the bike; Bluetooth® audio built in. Bike-ready build — conformal-coated PCB in an extruded aluminum heatsink. Flexible turn-on — REM / DC / VOX with status & clipping LEDs. Premium I/O — 4 AWG power, 12 AWG speaker busbar-style terminals. Best With Front & rear pro speakers at 2–4Ω Bridged 4Ω pairs for lids/mid-bass OFC wiring, correct fusing, and solid grounds Factory radio or DSP signal — we’ll help map gains/filters Tell us your bike and speakers — we’ll pre-map crossovers and gains for highway-clear performance. Key Specifications RMS @ 4Ω (14.4V) 120 × 4 RMS @ 2Ω (14.4V) 175 × 4 Bridged @ 4Ω (14.4V) 350 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD + N (10% rated power) 0.1% @ 2Ω per ch SNR (A-wt) / Damping Factor 91 dB / 200 DSP / Tuning 6-ch DSP (4 amp + 2 pass), Bluetooth® audio, USB-C PC tuning Turn-On Modes REM / DC / VOX Operating Voltage 9 – 16 V Current Draw (Music / Max) 50 A / 80 A Recommended Fuse (Music) 50 A Efficiency ~80% Gain Range 0.2 – 12 V Dimensions (with brackets) 5.3″ × 4.9″ × 2.0″ (134 × 125 × 51 mm) Dimensions (chassis) 4.1″ × 4.9″ × 2.0″ (104 × 125 × 51 mm) Specs per Cicada Audio product page. Always verify wiring/impedance and set gains conservatively. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean OFC wiring and correct fusing On-bike DSP tuning for loud, clear highway sound Nationwide shipping & tech support Need Help? Call (864) 334-6131. We’ll map gains, filters, and wiring for your exact setup.Sale -
Sale
Cicada Audio FLX1000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1000.4 — Compact 4-Channel Power for Bagger Audio Big output in a small chassis. The FLX1000.4 feeds your front + rear speakers real power from a palm-size, bike-ready amp. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a favorite for Harley-Davidson® and Indian® builds that need highway-clear sound without bulky gear. Why Riders Choose It Serious output — up to 254×4 @ 2Ω or 530×2 bridged @ 4Ω (14.4V). Compact chassis — 6.0″ × 4.9″ × 2.0″ fits behind fairings or in bags. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC options for easy integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring with correct fusing and clean grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 150 × 4 / 168 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 220 × 4 / 254 × 4 Bridged @ 4Ω (12.5V / 14.4V) 461 × 2 / 530 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) 60 A / 116 A Recommended Fuse (Music) 120 A Efficiency ~79% Dimensions (L × W × H) 6.0″ × 4.9″ × 2.0″ (152 × 124 × 51 mm) Specs from Cicada’s product page; retailer listings corroborate ratings and dimensions. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Can it run fronts and lids with one amp? Yes — many builds run four channels at 2–4Ω. Use HPF/LPF and proper gains for clean balance. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. Can I bridge it for more power? Yes — bridge pairs at 4Ω for up to ~530 W × 2 (14.4V). Use LPF for mid-bass or small sub duty. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (120 A music rec.). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale
THE REFERENCE STANDARD FOR CLEAN POWER INTEGRATION
Plug-and-play is how you build it right the first time—clean signal, correct turn-on behavior, and platform-correct integration without hacks. This is the GBS standard for real output at highway speed.
- No factory wire cutting — no guessing
- Platform-correct harnessing and signal integration
- Compact, motorcycle-ready form factors for real installs
WHAT YOU’RE BUILDING
- Clean install with correct integration
- Real power without splicing
- Factory or aftermarket radio compatibility
- Highway-speed performance you can trust
Plug-and-play amplifiers are the fastest way to go from “stock” to “built right” — clean integration first, then power and tuning.
Why Choose Plug-and-Play Amplifiers for Your Motorcycle
Not all amplifiers are motorcycle-ready. Plug-and-play amplifiers eliminate installation headaches by using platform-correct harnessing, proper signal integration, and compact form factors designed for fairings and saddlebag locations.
- No factory wire cutting — keep the bike clean and serviceable.
- Faster, cleaner installs using bike-specific wiring and mounting solutions.
- Proper signal voltage and turn-on behavior for reliable system operation.
- Compatibility with factory and aftermarket radios when paired with the correct harnessing.
- Reliable performance at highway speed — clean power delivery you can hear.
Built for Harley Touring Platforms
These plug-and-play amplifiers are designed to work with Harley-Davidson touring motorcycles when paired with the correct harnessing and installation parts.
- 2014–2023 Harley touring models
- 2023.5+ CVO and 2024+ touring platforms
- Fairing-mounted amplifier installs
- Saddlebag and rear speaker systems
Always confirm platform year and radio configuration before ordering.
What’s Included in This Plug-and-Play Amplifier Collection
- Motorcycle-specific plug-and-play amplifiers
- Amplifiers designed for fairing and saddlebag installs
- Compatible options for factory and aftermarket radios
- Power solutions for front stage, rear speakers, and subwoofers
- Amplifiers ready for DSP integration
Build the System the Right Way
A plug-and-play amplifier is one part of a complete system. For best results, pair your amplifier with platform-correct speakers, DSP tuning, and installation hardware.
If you’re unsure which amplifier fits your bike or goals, Garage Bagger Stereo can help you select the correct configuration.
High-output systems start with clean integration. Build it once, build it right.
Built to Withstand the Road
DS18 speakers are designed to endure the challenges of the open road while providing exceptional sound quality. Built using durable, weatherproof materials, these speakers are engineered to resist vibrations, impacts, and exposure to the elements without compromising on audio clarity.
Effortless Integration with Your Bagger Motorcycle
Designed for seamless integration, DS18 speakers fit effortlessly into your motorcycle’s audio system without sacrificing space or style. With user-friendly installation and advanced connectivity options, including Bluetooth and RCA inputs, DS18 ensures you can upgrade your sound system without sacrificing functionality.
Customizable Sound for Every Rider
From deep bass to crisp highs, DS18 speakers offer the customization to match your audio preferences. Featuring advanced DSP (Digital Signal Processing) technology, these speakers allow you to fine-tune your sound system for an optimal listening experience. Whether you prefer a balanced sound or a bass-heavy setup, DS18 speakers deliver versatile solutions for your needs.
Shop DS18 Audio at Garage Bagger Stereo
Explore our wide selection of DS18 speakers and motorcycle audio accessories at Garage Bagger Stereo. Whether you’re looking for a minor upgrade or a complete overhaul, we are your trusted destination for premium motorcycle audio gear. With expert guidance and top-notch customer service, we ensure you find the perfect audio solution for your ride.