-
SaleCicada Audio DSP600.4D — 4‑Channel Amplifier with DSP
Vendor:Cicada AudioMotorcycle Amplifier + DSP Cicada Audio DSP600.4D — Compact 4-Channel Power with Built-In DSP Clean power + smart control. The DSP600.4D packs a 4-channel class-D amp and a flexible DSP into a compact, bike-ready chassis. Dial in PEQ, high/low-pass filters up to 20 kHz, and steep slopes (up to 48 dB) so your Harley-Davidson® or Indian® system stays loud and clear at highway speed. Why Riders Choose It Built-in DSP — 8-band PEQ, HPF/LPF to 20 kHz, slopes 6/12/18/24/48 dB. Serious output — up to 152×4 @ 2Ω or 300×2 bridged @ 4Ω (14.4V). Compact chassis — fits cleanly behind fairings or in bags. Bike-ready — designed for motorcycle use. Plays nice with stock radios — easy gain structure and integration. Shop Motorcycle Amplifiers Best With Efficient front speakers (6.5″/horns) at 2–4Ω Rear lids or mid-bass channels with tailored PEQ & HPF/LPF Bridged 4Ω pairs for higher output OFC wiring, proper fusing, and careful gain setup Tell us your bike and speakers — we’ll pre-map crossovers, slopes, and PEQ to your setup. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 70 × 4 / 92 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 115 × 4 / 152 × 4 Bridged @ 4Ω (12.5V / 14.4V) 218 × 2 / 300 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 DSP Crossovers HPF/LPF 0–20 kHz; slopes 6/12/18/24/48 dB DSP PEQ 8 bands; Q 0.05–20 Operating Voltage 8 – 16 V Current Draw (Music / Max) 40 A / 80 A Recommended Fuse 40 A Efficiency ~79% Dimensions (L × W × H) 8.875″ × 4.0″ × 1.4″ (225.4 × 103 × 36 mm) Specs from Cicada’s product page and manual. Always verify impedance/wiring before power-on. Frequently Asked Questions — Motorcycle Audio Can I power fronts and lids with one amp? Yes, many builds run all four channels. Use the DSP to set independent HPF/LPF and PEQ per pair for clean, balanced output. Will it work with my factory radio? Yes — it integrates cleanly. Set gains carefully and use the DSP to correct the factory curve. Add a dedicated DSP if you need time alignment. Can I bridge for more power? Yes — bridge pairs at 4Ω for up to 300 W × 2 (14.4V). Enable LPF when driving mid-bass or a small sub. What wiring and fuse do I need? Use OFC power/ground sized for the current draw, fused at the battery (40 A). Keep grounds short with solid chassis bonding. Is it weather resistant? It’s designed for motorcycles. Mount away from direct spray and protect cables from abrasion and heat. Garage Bagger Stereo Advantage Bike-specific DSP presets on request Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and phone support Need Help? Call us at (864) 334-6131 with your bike, speakers, and goals. We’ll map crossovers, EQ, and gains for your exact setup.Sale -
Sale -
SaleCicada Audio FLX1000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1000.4 — Compact 4-Channel Power for Bagger Audio Big output in a small chassis. The FLX1000.4 feeds your front + rear speakers real power from a palm-size, bike-ready amp. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a favorite for Harley-Davidson® and Indian® builds that need highway-clear sound without bulky gear. Why Riders Choose It Serious output — up to 254×4 @ 2Ω or 530×2 bridged @ 4Ω (14.4V). Compact chassis — 6.0″ × 4.9″ × 2.0″ fits behind fairings or in bags. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC options for easy integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring with correct fusing and clean grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 150 × 4 / 168 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 220 × 4 / 254 × 4 Bridged @ 4Ω (12.5V / 14.4V) 461 × 2 / 530 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) 60 A / 116 A Recommended Fuse (Music) 120 A Efficiency ~79% Dimensions (L × W × H) 6.0″ × 4.9″ × 2.0″ (152 × 124 × 51 mm) Specs from Cicada’s product page; retailer listings corroborate ratings and dimensions. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Can it run fronts and lids with one amp? Yes — many builds run four channels at 2–4Ω. Use HPF/LPF and proper gains for clean balance. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. Can I bridge it for more power? Yes — bridge pairs at 4Ω for up to ~530 W × 2 (14.4V). Use LPF for mid-bass or small sub duty. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (120 A music rec.). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX1400.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1400.4 — High-Output 4-Channel Power for Bagger Audio More headroom, same compact footprint. The FLX1400.4 drives front + rear speakers with authority from a bike-ready chassis that tucks neatly behind fairings or in bags. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a go-to for Harley-Davidson® and Indian® builds that demand highway-clear output. This amplifier is part of our Motorcycle Amplifiers collection, built for Harley Davidson and Indian touring motorcycles. Why Riders Choose It Serious output — four strong channels or bridged pairs for lids/mid-bass. Compact chassis — mounts cleanly on touring platforms. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring, correct fusing, and solid grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (14.4V) ≈ 200 × 4 RMS Power @ 2Ω (14.4V) ≈ 350 × 4 Bridged @ 4Ω (14.4V) ≈ 700 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor ≈ 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) ≈ 70 A / 130 A Recommended Fuse (Music) ≈ 150 A Dimensions Compact motorcycle-grade chassis Always verify impedance, wiring, and fuse size for your exact setup. Frequently Asked Questions — Motorcycle Audio Can it power fronts and lids cleanly? Yes — run four channels at 2–4Ω for a balanced system, or bridge pairs at 4Ω for more output to lids or mid-bass. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (≈150 A music). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX1400.4P — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1400.4P — High-Output 4-Channel Power for Bagger Audio More headroom, same compact footprint. The FLX1400.4P drives front + rear speakers with authority from a bike-ready chassis that tucks neatly behind fairings or in bags. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a go-to for Harley-Davidson® and Indian® builds that demand highway-clear output. Why Riders Choose It Serious output — four strong channels or bridged pairs for lids/mid-bass. Compact chassis — mounts cleanly on touring platforms. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring, correct fusing, and solid grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (14.4V) ≈ 200 × 4 RMS Power @ 2Ω (14.4V) ≈ 350 × 4 Bridged @ 4Ω (14.4V) ≈ 700 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor ≈ 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) ≈ 70 A / 130 A Recommended Fuse (Music) ≈ 150 A Dimensions Compact motorcycle-grade chassis Always verify impedance, wiring, and fuse size for your exact setup. Frequently Asked Questions — Motorcycle Audio Can it power fronts and lids cleanly? Yes — run four channels at 2–4Ω for a balanced system, or bridge pairs at 4Ω for more output to lids or mid-bass. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (≈150 A music). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX2000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX2000.4 — Compact 4-Channel Power for Bagger Audio Big-boy power, small footprint. The FLX2000.4 drives front + rear speakers with serious output from a compact, bike-ready chassis. With HPF/LPF crossovers, REM/DC turn-on, and clean tuning, it’s built for Harley-Davidson® and Indian® touring systems that need highway-clear volume without bulky gear. This amplifier is part of our Motorcycle Amplifiers collection, built for Harley Davidson and Indian touring motorcycles. Why Riders Choose It Serious output — up to 542×4 @ 2Ω or 1044×2 bridged @ 4Ω (14.4V). Compact chassis — 8.6″ × 4.9″ × 2.0″ tucks behind fairings/bags. Bike-ready — conformal-coated PCB, designed for motorcycles. Flexible turn-on — REM / DC integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring with 4 AWG power & correct fusing Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 275 × 4 / 331 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 450 × 4 / 542 × 4 Bridged @ 4Ω (12.5V / 14.4V) 866 × 2 / 1044 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) 60 A / 240 A Recommended Fuse (Music) 120 A Efficiency ~79% Gain Range 0.2 – 12 V Dimensions (L × W × H) 8.6″ × 4.9″ × 2.0″ (218 × 124 × 51 mm) Specs from Cicada’s product page and manual; multiple dealers corroborate power ratings and crossover ranges. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Can it run fronts and lids with one amp? Yes — many builds run four channels at 2–4Ω. Use HPF/LPF and proper gains for clean balance. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. Can I bridge it for more power? Yes — bridge pairs at 4Ω for up to ~1044 W × 2 (14.4V). Use LPF for mid-bass duty as needed. What wiring and fuse do I need? Use OFC power/ground with 4 AWG power and fuse at the battery (120 A music). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes with conformal-coated PCB. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX1600.1 — Mono Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier — Mono Cicada Audio FLX1600.1 — High-Output Mono Power for Bagger Audio One channel, no compromise. The FLX1600.1 is a mono full-range workhorse for high-output lids, mid-bass, or a compact sub. It packs serious wattage into a compact, bike-ready chassis with HPF/LPF control and clean integration on Harley-Davidson® and Indian® touring platforms. Why Riders Choose It Serious output — up to 1600 × 1 @ 2Ω (14.4V). Compact chassis — 8.6″ × 4.9″ × 2.0″ tucks behind fairings/bags. Bike-ready — element-ready design for motorcycle use. Flexible turn-on — REM / DC integration. On-board crossovers — HPF 10–80 Hz; LPF 80 Hz–20 kHz, 12 dB/oct. Shop Motorcycle Amplifiers Best With High-output lids or mid-bass at 2–4Ω Compact 4Ω subwoofer (enable LPF) OFC wiring & correct fusing; careful gain setup Factory radio or DSP front-end Tell us your bike and speakers — we’ll map crossovers, slopes, and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 670 × 1 / 950 × 1 RMS Power @ 2Ω (12.5V / 14.4V) 1250 × 1 / 1600 × 1 Frequency Response 10 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 86 dB / 200 Crossovers HPF 10–80 Hz; LPF 80 Hz–20 kHz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 9 – 16 V Current Draw (Music / Max) 70 A / 140 A Recommended Fuse (Music) 100 A Efficiency ~80% Gain Range 0.2 – 12 V Dimensions (L × W × H) 8.6″ × 4.9″ × 2.0″ (218 × 124 × 51 mm) Specs from Cicada’s product page; multiple dealers corroborate power ratings and crossover ranges. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Is this for subs or mids? Both. It’s a mono full-range design. Use HPF for mid-bass/lids or LPF for a compact sub. We’ll help you choose the right filter points. Will it work with my factory radio? Yes — use DC or REM turn-on and set gains carefully. Add DSP if you need advanced EQ or time alignment. What wiring and fuse should I use? Use OFC wire sized for current draw and fuse at the battery (100 A music). Keep grounds short with solid chassis bonding. Is it motorcycle-ready? Yes — element-ready construction. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX2500.1 — Mono Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier — Mono Cicada Audio FLX2500.1 — High-Output Mono Power for Bagger Audio One channel, maximum punch. The FLX2500.1 is a mono full-range workhorse for high-output lids, mid-bass, or a compact sub. It packs big wattage into a compact, bike-ready chassis, with HPF/LPF control and clean integration on Harley-Davidson® and Indian® touring platforms. Why Riders Choose It Serious output — up to 2500 × 1 @ 2Ω (14.4V). Compact chassis — 9.2″ × 4.9″ × 2.0″ tucks behind fairings/bags. Bike-ready — element-ready design for motorcycles. Flexible turn-on — REM / DC integration. On-board crossovers — HPF 10–80 Hz; LPF 80 Hz–20 kHz, 12 dB/oct. Cicada recommends a lithium battery upgrade and 2 AWG power wire for this model. Best With High-output lids or mid-bass at 2–4Ω Compact 4Ω subwoofer (enable LPF) OFC wiring & correct fusing; careful gain setup Factory radio or DSP front-end Tell us your bike and speakers — we’ll map crossovers, slopes, and gains for loud, clean highway performance. Key Specifications RMS Power @ 2Ω (14.4V) 2500 × 1 Frequency Response 10 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% @ 10% rated power) SNR (A-wt) / Damping Factor 86 dB / 200 Crossovers HPF 10–80 Hz; LPF 80 Hz–20 kHz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 9 – 16 V Current Draw (Music / Max) 80 A / 260 A Recommended Fuse (Music) 150 A Total Efficiency ~80% Gain Range 0.2 – 12 V Dimensions (L × W × H) 9.2″ × 4.9″ × 2.0″ (234 × 124 × 51 mm) Specs pulled from Cicada’s official page; multiple dealers corroborate power, dimensions, and fuse guidance. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Is this for subs or mids? Both. It’s a mono full-range design. Use HPF for mid-bass/lids or LPF for a compact sub. We’ll help you choose the right filter points. Will it work with my factory radio? Yes — use DC or REM turn-on and set gains carefully. Add DSP if you need advanced EQ or time alignment. What wiring and battery should I use? Run 2 AWG power, fuse at the battery (150 A music), and use a lithium battery upgrade as recommended by Cicada. Is it motorcycle-ready? Yes — element-ready construction. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleDB Drive Euphoria XPERT EX100.4 Full Range Class D 4-Channel Amplifier
Vendor:DB DriveTRUE SOUND. TRUE SOURCE. EX100.4 : 4 Channel Full Range Class D Amplifier Achieve superior audio performance with the XPERT EX100.4, engineered for high output in a compact design—ideal for motorcycle and space-limited applications. Capable of powering high-performance tweeter, compression drivers, and midranges with ease. Features 4 Channel Class D Circuitry ACT - Adaptive Crossover Technology High efficiency Full Range Class D Technology Direct Connect Speaker Terminals Large Gauge Power Wire Inputs APC - Audio Protection Circuit SESI - Signal Evaluation Status Indicator $299.98 Specifications @14.4 Volts - 1% THD 4 x 50 Watts @ 4 Ohm 4 x 100 Watts @ 2 Ohm 2 x 200 Watts @ 4 Ohm (Bridged) Working Voltage: 10 - 16 Volts Frequency Response: 10Hz - 20KHz Signal to Noise Ratio: < 85dB Damping Factor @ 4 Ohm > 57/ 1KHz Low Level Input: 6V - 0.2V Ch 1/2 High Pass Filter Variable: 20Hz - 5KHz Ch 1/2 Low Pass Filter Variable: 50Hz - 5KHz Ch 3/4 High Pass Filter Variable: 20Hz - 5KHz Ch 3/4 Low Pass Filter Variable: 50Hz - 5KHz Minimum Working Impedance: 2 Ohm Stereo Dimensions L - 5" / 127mm W - 5.20" / 132.08mm H - 2.50" / 63.50mmSale -
SaleDB Drive Euphoria XPERT EX200.4 Full Range Class D 4-Channel Amplifier
Vendor:DB DriveTRUE SOUND. TRUE SOURCE. EX200.4 : 4 Channel Full Range Class D Amplifier Achieve superior audio performance with the XPERT EX200.4, engineered for high output in a compact design—ideal for motorcycle and space-limited applications. Capable of powering high-performance tweeter, compression drivers, and midranges with ease. Features 4 Channel Class D Circuitry ACT - Adaptive Crossover Technology High efficiency Full Range Class D Technology Direct Connect Speaker Terminals Large Gauge Power Wire Inputs APC - Audio Protection Circuit SESI - Signal Evaluation Status Indicator $599.98 Specifications @14.4 Volts - 1% THD 4 x 200 Watts @ 4 Ohm 4 x 300 Watts @ 2 Ohm 2 x 400 Watts @ 4 Ohm (Bridged) Working Voltage: 10 - 16 Volts Frequency Response: 10Hz - 20KHz Signal to Noise Ratio: < 95dB Damping Factor @ 4 Ohm > 101/ 1KHz Low Level Input: 6V - 0.2V Ch 1/2 High Pass Filter Variable: 20Hz - 5KHz Ch 1/2 Low Pass Filter Variable: 50Hz - 5KHz Ch 3/4 High Pass Filter Variable: 20Hz - 5KHz Ch 3/4 Low Pass Filter Variable: 50Hz - 5KHz Minimum Working Impedance: 2 Ohm Stereo Dimensions L - 7.45" / 189.23mm W - 5.20" / 132.08mm H - 2.50" / 63.50mmSale -
SaleDB Drive Euphoria XPERT EX300.4 Full Range Class D 4-Channel Amplifier
Vendor:DB DriveTRUE SOUND. TRUE SOURCE. EX300.4 : 4 Channel Full Range Class D Amplifier Achieve superior audio performance with the XPERT EX300.4, engineered for high output in a compact design—ideal for motorcycle and space-limited applications. Capable of powering high-performance tweeter, compression drivers, and midranges with ease. Features 4 Channel Class D Circuitry ACT - Adaptive Crossover Technology High efficiency Full Range Class D Technology Direct Connect Speaker Terminals Large Gauge Power Wire Inputs APC - Audio Protection Circuit SESI - Signal Evaluation Status Indicator $699.98 Specifications @14.4 Volts - 1% THD 4 x 300 Watts @ 4 Ohm 4 x 500 Watts @ 2 Ohm 2 x 600 Watts @ 4 Ohm (Bridged) Working Voltage: 10 - 16 Volts Frequency Response: 10Hz - 20KHz Signal to Noise Ratio: < 95dB Damping Factor @ 4 Ohm > 114/ 1KHz Low Level Input: 6V - 0.2V Ch 1/2 High Pass Filter Variable: 20Hz - 5KHz Ch 1/2 Low Pass Filter Variable: 50Hz - 5KHz Ch 3/4 High Pass Filter Variable: 20Hz - 5KHz Ch 3/4 Low Pass Filter Variable: 50Hz - 5KHz Minimum Working Impedance: 2 Ohm Stereo Dimensions L - 9" / 228.6mm W - 5.20" / 132.08mm H - 2.50" / 63.50mmSale -
SaleDB Drive Euphoria XPERT EX1500.1 Full Range Class D Monoblock Amplifier
Vendor:DB DriveTRUE SOUND. TRUE SOURCE. EX1500.1 : Monoblock Full Range Class D Amplifier Achieve superior audio performance with the XPERT EX1500.1, engineered for high output in a compact design—ideal for motorcycle and space-limited applications. Capable of powering high-performance tweeter, compression drivers, and midranges with ease. Features ACT - Adaptive Crossover Technology High efficiency Full Range Class D Technology Direct Connect Speaker Terminals Large Gauge Power Wire Inputs APC - Audio Protection Circuit SESI - Signal Evaluation Status Indicator $599.98 Specifications @14.4 Volts - 1% THD 1 x 1500 Watts @ 1 Ohm 1 x 750 Watts @ 2 Ohm 1 x 325 Watts @ 4 Ohm Working Voltage: 10 - 16 Volts Frequency Response: 10Hz - 20KHz Signal to Noise Ratio: < 95dB Damping Factor @ 4 Ohm > 91/ 1KHz Low Level Input: 6V - 0.2V High Pass VariableFilter: 20Hz - 800Hz / 200Hz - 8KHz Low Pass Variable Filter: 50Hz - 800Hz / 500 Hz - 8KHz Minimum Working Impedance: 1 Ohm Stereo Dimensions L - 9" / 228.6mm W - 5.20" / 132.08mm H - 2.50" / 63.50mmSale
-
Sale
Cicada Audio DSP600.4D — 4‑Channel Amplifier with DSP
Vendor:Cicada AudioMotorcycle Amplifier + DSP Cicada Audio DSP600.4D — Compact 4-Channel Power with Built-In DSP Clean power + smart control. The DSP600.4D packs a 4-channel class-D amp and a flexible DSP into a compact, bike-ready chassis. Dial in PEQ, high/low-pass filters up to 20 kHz, and steep slopes (up to 48 dB) so your Harley-Davidson® or Indian® system stays loud and clear at highway speed. Why Riders Choose It Built-in DSP — 8-band PEQ, HPF/LPF to 20 kHz, slopes 6/12/18/24/48 dB. Serious output — up to 152×4 @ 2Ω or 300×2 bridged @ 4Ω (14.4V). Compact chassis — fits cleanly behind fairings or in bags. Bike-ready — designed for motorcycle use. Plays nice with stock radios — easy gain structure and integration. Shop Motorcycle Amplifiers Best With Efficient front speakers (6.5″/horns) at 2–4Ω Rear lids or mid-bass channels with tailored PEQ & HPF/LPF Bridged 4Ω pairs for higher output OFC wiring, proper fusing, and careful gain setup Tell us your bike and speakers — we’ll pre-map crossovers, slopes, and PEQ to your setup. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 70 × 4 / 92 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 115 × 4 / 152 × 4 Bridged @ 4Ω (12.5V / 14.4V) 218 × 2 / 300 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 DSP Crossovers HPF/LPF 0–20 kHz; slopes 6/12/18/24/48 dB DSP PEQ 8 bands; Q 0.05–20 Operating Voltage 8 – 16 V Current Draw (Music / Max) 40 A / 80 A Recommended Fuse 40 A Efficiency ~79% Dimensions (L × W × H) 8.875″ × 4.0″ × 1.4″ (225.4 × 103 × 36 mm) Specs from Cicada’s product page and manual. Always verify impedance/wiring before power-on. Frequently Asked Questions — Motorcycle Audio Can I power fronts and lids with one amp? Yes, many builds run all four channels. Use the DSP to set independent HPF/LPF and PEQ per pair for clean, balanced output. Will it work with my factory radio? Yes — it integrates cleanly. Set gains carefully and use the DSP to correct the factory curve. Add a dedicated DSP if you need time alignment. Can I bridge for more power? Yes — bridge pairs at 4Ω for up to 300 W × 2 (14.4V). Enable LPF when driving mid-bass or a small sub. What wiring and fuse do I need? Use OFC power/ground sized for the current draw, fused at the battery (40 A). Keep grounds short with solid chassis bonding. Is it weather resistant? It’s designed for motorcycles. Mount away from direct spray and protect cables from abrasion and heat. Garage Bagger Stereo Advantage Bike-specific DSP presets on request Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and phone support Need Help? Call us at (864) 334-6131 with your bike, speakers, and goals. We’ll map crossovers, EQ, and gains for your exact setup.Sale -
Sale
-
Sale
Cicada Audio FLX1000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1000.4 — Compact 4-Channel Power for Bagger Audio Big output in a small chassis. The FLX1000.4 feeds your front + rear speakers real power from a palm-size, bike-ready amp. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a favorite for Harley-Davidson® and Indian® builds that need highway-clear sound without bulky gear. Why Riders Choose It Serious output — up to 254×4 @ 2Ω or 530×2 bridged @ 4Ω (14.4V). Compact chassis — 6.0″ × 4.9″ × 2.0″ fits behind fairings or in bags. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC options for easy integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring with correct fusing and clean grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 150 × 4 / 168 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 220 × 4 / 254 × 4 Bridged @ 4Ω (12.5V / 14.4V) 461 × 2 / 530 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) 60 A / 116 A Recommended Fuse (Music) 120 A Efficiency ~79% Dimensions (L × W × H) 6.0″ × 4.9″ × 2.0″ (152 × 124 × 51 mm) Specs from Cicada’s product page; retailer listings corroborate ratings and dimensions. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Can it run fronts and lids with one amp? Yes — many builds run four channels at 2–4Ω. Use HPF/LPF and proper gains for clean balance. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. Can I bridge it for more power? Yes — bridge pairs at 4Ω for up to ~530 W × 2 (14.4V). Use LPF for mid-bass or small sub duty. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (120 A music rec.). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
Sale
Cicada Audio FLX1400.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1400.4 — High-Output 4-Channel Power for Bagger Audio More headroom, same compact footprint. The FLX1400.4 drives front + rear speakers with authority from a bike-ready chassis that tucks neatly behind fairings or in bags. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a go-to for Harley-Davidson® and Indian® builds that demand highway-clear output. This amplifier is part of our Motorcycle Amplifiers collection, built for Harley Davidson and Indian touring motorcycles. Why Riders Choose It Serious output — four strong channels or bridged pairs for lids/mid-bass. Compact chassis — mounts cleanly on touring platforms. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring, correct fusing, and solid grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (14.4V) ≈ 200 × 4 RMS Power @ 2Ω (14.4V) ≈ 350 × 4 Bridged @ 4Ω (14.4V) ≈ 700 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor ≈ 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) ≈ 70 A / 130 A Recommended Fuse (Music) ≈ 150 A Dimensions Compact motorcycle-grade chassis Always verify impedance, wiring, and fuse size for your exact setup. Frequently Asked Questions — Motorcycle Audio Can it power fronts and lids cleanly? Yes — run four channels at 2–4Ω for a balanced system, or bridge pairs at 4Ω for more output to lids or mid-bass. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (≈150 A music). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale
Cutting-Edge technology for Superior Sound
Our motorcycle amplifiers are equipped with the latest technology to deliver unmatched sound quality. From Class D amplifiers that provide efficient power with minimal current draw to advanced audio systems that ensure clear audio signals, our amps are built for the audiophile rider. With available features like high pass filters and watts RMS ratings, you'll enjoy every note and beat with precision and clarity.
Compact Designs for Easy Installation
We understand that space is a premium when it comes to motorcycle audio. That's why we carry amplifier choices that come with a small footprint and are designed for easy installation in tight spaces. Whether you're fitting an amp in your Harley-Davidson's fairing or under a seat, we carry everything you need, including wiring harnesses and installation instructions. Say goodbye to bulky amps and hello to sleek, powerful audio solutions.
Built for the Road
Our motorcycle amplifiers are not just about great sound; they're also built to withstand the rigors of the road. From vibration-resistant amp enclosures to weatherproof designs, our amps are ready for any adventure. Whether you're riding a Road Glide or an off-road vehicle, our amplifiers are engineered to perform in any environment, ensuring your music never skips a beat.
Customize Your Sound Expierence
Take control of your audio experience with our motorcycle amplifiers. With features like volume control, adjustable power ratings, and multiple channel options, you can tailor your sound system to your preferences. Whether you're looking for a powerful bass or clear highs, our amplifiers provide the flexibility to create the perfect audio setup for your ride.
Garage Bagger: Only Carrying the Best
At Garage Bagger Stereo, we're dedicated to providing top-tier audio equipment, and our Motorcycle Amplifiers are a prime example of the elite brands we offer. Understanding the importance of excellent sound for your ride or sail, we feature an exceptional range of parts. We know selecting the right gear can be daunting, so our expert team, armed with extensive knowledge and enthusiasm for audio, is ready to assist you in finding the ideal setup for your motorcycle or boat. Thank you for considering Dirty Bird at Garage Bagger Stereo, where premium quality and expert guidance are our standards.