Browse Collections
-
Arc Audio PSM Pro Digital Sound Processor | Plug and Play
Vendor:Arc AudioHarley Davidson Minature Pro Digital Sound Processor Plug and Play for stock radios 14-23 Harley Davidson Models Plug and Play for stock radios and amps 23 CVO to current Harley Davidson Models The ARC Audio PSM Pro digital sound processor is a small but powerful device designed to enhance the audio quality of your car or motorcycle's sound system. It is an upgraded version of the PSM offering even better performance and 8 output channels.The PSM Pro uses advanced 32-bit DSP technology and has 296 total bands of full variable parametric equalization, open architecture crossover selection, signal delay, and phase control. This allows you to tune your audio system to your specific preferences and improve the quality of your listening experience. Processor Type Stand Alone Unit Processor Resolution 32-Bits Sample Rate 96kHz Analog Inputs 6 CH. Differential in (RCA or Speaker Level) Input Sensitivity 2V - 16V RMS Digital Inputs Coaxial Auto-sense Turn-On DC (BTL) (Uses Ch 1/2 Inputs Only) Outputs (RCA) 8-Channels Outputs Voltage (RCA) Up to 3.5V Input Impedance (RCA) 10k ohms Frequency Response 20Hz - 23.5kHz S/N Ratio 1V 1:1 86dB S/N 4V 1:1 90dB Operating Voltage 6V - 17.0V (Start Stop Compliance to 4.5V) Output Equalization 31 Band + 6 (37 Band) X 8 Parametric EQ, Highpass Shelf, Lowpass Shelf, 1st & 2nd order Allpass. (296 Total Bands Output Equalization Resolution 0.01dB dB per step +18dB / -24dB Output Signal Delay Up to 30ms per channel in .01ms increments (Fixed Point Delay) Input Signal Mixer Yes - 8-Channels In (Including Digital) x 8-Channels Out Advanced Mixer (Output Signal Mixer) Yes Easy-to-use Mixer Assistant Yes Crossovers Phase Correct AP/HP/LP/BP all channels Crossover Slopes 6dB, 12dB, 18dB, 24dB, 30dB, 36dB, 42dB, 48dB Slopes all bands all channels Crossover Types Butterworth, Linkwitz-Riley, Bessel, Variable Q, Chebyshev (all channels all bands) Crossover selectable frequencies 10Hz - 20kHz in 0.1 Hz increments) Output Signal up mixer Yes Input Signal Equalization 12 Bands Parametric (linkable) Per Channel Input Equalization Resolution 1/10th dB per step +18dB / -24dB Input Equalization All Pass Filters Yes - Individual per input EQ band Input Signal Delay Yes - Up to 11.04ms per channel input Presets Up to 4-Presets External Remote Level Control Yes (LR1 Sold Separately) AXP WiFi control adapter card No Preset selection without controller use Yes - Optional manual trigger switches +/- for up to 4 presets (Not Included) Remote Turn-On Output Controls Turn on Output (up to 40ms), Turn-on Hold (up to 40ms), Auto-sense hold time (up to 200ms) Remote Turn-On Output On/Off lead timing control Remote on/off adjustable up to 40 seconds each Maestro AR Module interface capable Yes - Requires Maestro T-Harness, and data cable for connection. Expansion Capability PSM-Pro can be run in multiples with individual USB connections to a single PC with single operating software being used Software Interface 64 bit Windows 8, Windows 8.1 or Windows 10 Dimensions 3.75"(L) x 3.0"(W) x 1.35"(H) -
SaleCicada Audio CHX525 5.25" Pro Coaxial Speaker (Pair)
Vendor:Cicada AudioCHX525.2 or .4Ω HIGH-PERFORMANCE PRO COAX HORN SPEAKERS New to our pro-line horn series, the CHX525.2 5.25″ coax horn speaker features a 1.5″, 2Ω, voice coil woofer and a 1.0″ horn, 8Ω, tweeter. It handles big power and is high-performance. 150w RMS / 300w MAX Power Handling each Heavy duty diecast basket 1.5″ high temp voice coil for mid-bass 1.0″ high temp voice coil for tweeter Freq Response: 90Hz – 20kHz +/- 5dB 91dB Sensitivity External 12dB / 6kHz tweeter crossover Mounting Depth: 2.26″ / 70mm Mounting Diameter: 5.25″ / 133mmSale -
SaleCicada Audio CXX525 5.25" Pro Coaxial Speakers | 2Ω or 4Ω – Pair
Vendor:Cicada Audio5.25-INCH MOTORCYCLE PRO COAXIAL AUDIO Cicada Audio CXX525 5.25" Pro Coaxial Speakers | 2Ω or 4Ω – Pair The Cicada Audio CXX525 is a high-performance 5.25-inch Pro Coaxial speaker pair available in 2Ω and 4Ω versions. Each speaker combines a lightweight Kevlar cone, integrated PEI tweeter, V8™ Dispersion Guide and compact neodymium motor for clear, efficient motorcycle audio performance in demanding open-air riding conditions. Choose Impedance View Specifications Compact Pro Coaxial Performance Available in 2Ω and 4Ω configurations Sold as a matched pair 100 watts RMS per speaker 200 watts maximum per speaker Kevlar mid-bass cones Integrated PEI dome tweeters Built-in 6dB crossover V8™ Dispersion Guide for wide tweeter output Rain or Shine™ all-weather construction Protective grilles and hardware included Cicada CXX525 Pro Coaxial Overview The Cicada Audio CXX525 is designed for motorcycle audio systems that need full-range sound from a compact 5.25-inch speaker platform. Its coaxial design combines the mid-bass driver and tweeter into one speaker assembly. This reduces the number of separate components required while providing strong mid-bass, clear vocals and high-frequency detail from compatible factory or custom motorcycle speaker locations. Select the CXX525.2 2Ω version or the CXX525.4 4Ω version based on your amplifier, channel configuration and final speaker impedance. Available Impedance Options and SKUs CXX525.2 — 2-Ohm Version Select the 2Ω version when your amplifier is stable at the intended 2-ohm channel load and your complete speaker wiring is designed for the lower impedance. CXX525.4 — 4-Ohm Version Select the 4Ω version for amplifiers and multi-speaker systems designed around a 4-ohm channel load. Choose the correct impedance: The proper version depends on your amplifier’s rated load, the number of speakers connected to each channel and the complete series or parallel wiring configuration. What Comes in the Box Two Cicada Audio CXX525 5.25-inch Pro Coaxial speakers Selected 2Ω or 4Ω speaker configuration Two protective 5.25-inch speaker grilles Speaker installation hardware Important: Motorcycle-specific speaker adapters, fairing brackets, wiring harnesses, amplifier wiring and signal integration components are not included unless specifically added as product options. Why Riders Choose the CXX525 100W RMS Power Handling Each 5.25-inch speaker handles 100 watts RMS and 200 watts maximum for strong output from a properly matched motorcycle amplifier. 2Ω or 4Ω Variants Two impedance options allow the speakers to be matched to different amplifiers, channel loads and multi-speaker configurations. Pro Coaxial Design The integrated mid-bass driver and tweeter provide full-range output without requiring a separately mounted tweeter. V8™ Dispersion Guide Cicada’s dispersion guide is designed to distribute tweeter output more evenly around the speaker for broader high-frequency coverage. Kevlar Cone The lightweight Kevlar cone is strong, heat resistant and moisture resistant for efficient, controlled mid-bass performance. All-Weather Construction Rain or Shine™ construction and UV-protected surfaces are designed for exposed motorcycle audio environments. CXX525 Speaker Technology V8™ Dispersion Guide supports wide high-frequency dispersion from the integrated tweeter Built-in 6dB crossover manages the transition between the mid-bass driver and integrated tweeter Kevlar cone provides a lightweight, rigid and moisture-resistant speaker diaphragm PEI tweeter dome delivers bright, efficient high-frequency output Copper voice coils support efficient conductivity while helping control heat N45H neodymium motor provides strong output without the weight of a conventional ferrite motor Custom-tooled polycarbonate basket is designed for high-temperature motorcycle installations UV-protected surfaces help resist fading and damage from extended exposure to sunlight Cicada CXX525 Specifications Available Models CXX525.2 and CXX525.4 Speaker Type 5.25-inch high-performance Pro Coaxial speaker Quantity Pair Impedance Options 2Ω or 4Ω 2Ω Variant SKU CXX525.2 4Ω Variant SKU CXX525.4 Power Handling 100W RMS / 200W maximum per speaker Mid-Bass Voice Coil 1.4 inches / 35mm Tweeter Voice Coil 1 inch / 25mm Cone Material Kevlar Tweeter Dome PEI Built-In Crossover 6dB Magnet N45H neodymium Sensitivity 91dB, 1W / 1M Frequency Response 50Hz–20kHz ±3dB Mounting Depth Approximately 2.25 inches / 57mm Mounting Diameter 4.6 inches / 116mm Grilles Included Warranty Two-year manufacturer warranty Motorcycle Fitment Cicada Audio designs the CXX525 for compatible factory-style speaker locations used in Harley-Davidson, Indian and Honda motorcycle audio applications. Verify fitment: Confirm the motorcycle year, model, factory audio package, speaker opening, mounting depth, grille clearance, connector type and required mounting adapters before ordering. Compatible with properly sized 5.25-inch motorcycle speaker locations. Model-specific mounting brackets or adapters may be required. Factory speaker connectors may require an adapter or new terminals. Confirm the 4.6-inch mounting opening before installation. Confirm approximately 2.25 inches of available mounting depth. Verify that the included grille fits the intended installation location. Amplifier and Crossover Setup Protect the speakers: The built-in crossover divides frequencies between the mid-bass driver and tweeter, but the amplifier still requires an appropriate high-pass filter and properly set gain. Select CXX525.2 for a compatible 2Ω amplifier channel load. Select CXX525.4 for a compatible 4Ω amplifier channel load. Do not connect a 2Ω speaker to an amplifier channel not rated for 2Ω operation. Confirm final impedance when multiple speakers share one amplifier channel. Use an appropriate high-pass crossover for the speaker location and system goals. Set amplifier gain using clean measured output rather than control position alone. Reduce low-frequency output that exceeds the speaker’s operating range. Professional system tuning is recommended. Best For Compatible Harley-Davidson factory-style 5.25-inch locations Compatible Indian motorcycle speaker locations Compatible Honda motorcycle speaker locations Motorcycle fairing and rear-pod speaker upgrades Amplified systems requiring a 2Ω speaker option Amplified systems requiring a 4Ω speaker option Riders wanting full-range sound from a compact coaxial platform Custom motorcycle and powersports audio installations Related Motorcycle Audio Categories Cicada and Motorcycle Speakers Shop Cicada Audio Shop Motorcycle Speakers 2023.5+ / 2024+ Harley Plug-and-Play Kits Amplifiers and Signal Motorcycle Amplifiers Motorcycle Amplifier Installation Parts Motorcycle DSP and Signal Integration Installation Support Motorcycle Batteries Motorcycle Audio Installation in Taylors, SC Request a Custom Audio Build Cicada CXX525 FAQ Is this listing for the 2Ω or 4Ω version? This single listing includes both versions. Select CXX525.2 for the 2Ω speaker pair or CXX525.4 for the 4Ω speaker pair before adding the product to your cart. Are the CXX525 speakers sold individually or as a pair? Both the CXX525.2 and CXX525.4 variants are sold as a pair. Which impedance should I choose? Choose the impedance supported by your amplifier and complete speaker wiring plan. The final channel load depends on the number of speakers connected and whether they are wired individually, in series or in parallel. How much power can the CXX525 handle? Each speaker is rated for 100 watts RMS and 200 watts maximum power. Are these coaxial speakers? Yes. Each CXX525 combines a 5.25-inch mid-bass driver and integrated tweeter in one Pro Coaxial speaker assembly. Does the CXX525 use an external crossover? No external component crossover is required for the integrated tweeter. The speaker includes a built-in 6dB crossover. Are speaker grilles included? Yes. The speaker pair includes protective grilles and installation hardware. Will these fit every 5.25-inch motorcycle speaker location? No. Fitment depends on the motorcycle year, model, speaker opening, mounting depth, grille clearance and required mounting adapters. Does this speaker pair need an amplifier? A properly matched motorcycle amplifier that is stable at the selected speaker impedance is recommended to take advantage of the speakers’ output and power handling. What warranty does Cicada Audio provide? Cicada Audio lists a two-year manufacturer warranty for both CXX525 impedance variants. Need Help Choosing 2 Ohms or 4 Ohms? Call Garage Bagger Stereo with your motorcycle year, model, speaker locations, amplifier and planned wiring. We’ll help determine which CXX525 impedance is correct and identify the proper mounting, wiring and signal-integration components for your system. Call 864-334-6131 Ask GBS for HelpSale -
SaleCicada Audio FLX1000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1000.4 — Compact 4-Channel Power for Bagger Audio Big output in a small chassis. The FLX1000.4 feeds your front + rear speakers real power from a palm-size, bike-ready amp. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a favorite for Harley-Davidson® and Indian® builds that need highway-clear sound without bulky gear. Why Riders Choose It Serious output — up to 254×4 @ 2Ω or 530×2 bridged @ 4Ω (14.4V). Compact chassis — 6.0″ × 4.9″ × 2.0″ fits behind fairings or in bags. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC options for easy integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring with correct fusing and clean grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 150 × 4 / 168 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 220 × 4 / 254 × 4 Bridged @ 4Ω (12.5V / 14.4V) 461 × 2 / 530 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) 60 A / 116 A Recommended Fuse (Music) 120 A Efficiency ~79% Dimensions (L × W × H) 6.0″ × 4.9″ × 2.0″ (152 × 124 × 51 mm) Specs from Cicada’s product page; retailer listings corroborate ratings and dimensions. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Can it run fronts and lids with one amp? Yes — many builds run four channels at 2–4Ω. Use HPF/LPF and proper gains for clean balance. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. Can I bridge it for more power? Yes — bridge pairs at 4Ω for up to ~530 W × 2 (14.4V). Use LPF for mid-bass or small sub duty. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (120 A music rec.). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX1400.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioCicada Audio FLX1400.4 4-Channel Motorcycle Amplifier The Cicada Audio FLX1400.4 is a high-output 4-channel motorcycle amplifier built for Harley-Davidson bagger audio systems that need serious clean power, strong speaker control, and reliable highway-speed output. This amplifier is a strong fit for riders powering fairing speakers, saddlebag lid speakers, midbass, or bridged speaker pairs in a loud, clean, motorcycle-ready audio build. Cicada Amplifiers Motorcycle Amplifiers Shop Cicada Audio THE REFERENCE STANDARD Clean 4-Channel Power for Harley Bagger Audio Built for riders who need compact motorcycle amplifier power, flexible crossover control, 2Ω/4Ω speaker support, and strong output for real Harley audio systems. Start a Build Consultation Call 864-334-6131 Key Product Details Product Cicada Audio FLX1400.4 4-Channel Motorcycle Amplifier Amplifier Type High-output 4-channel motorcycle amplifier Best For Harley-Davidson bagger audio, fairing speakers, saddlebag lid speakers, midbass, and amplified motorcycle audio systems System Goal Clean power, stronger output, better speaker control, and louder highway-speed performance Speaker Support 2Ω and 4Ω speaker systems, depending on final wiring and system design Install Focus Compact motorcycle amplifier layout for Harley-Davidson Touring and custom bagger audio builds Always verify speaker impedance, wiring layout, fuse size, amplifier placement, gain structure, and system design before ordering or installing this amplifier. Built for High-Output Harley Audio Systems The Cicada FLX1400.4 is built for Harley-Davidson and motorcycle audio systems where factory power is not enough. It gives riders the headroom needed to drive upgraded 6.5" speakers, 6x9 speakers, pro coaxials, midbass drivers, and bridged speaker pairs with cleaner output and better control. This amplifier is a strong choice when the goal is louder vocals, stronger midbass, reduced distortion, and better open-air performance at speed. In a properly planned Harley bagger audio system, the FLX1400.4 can support front and rear speaker layouts, fairing and lid speaker upgrades, or bridged power for more aggressive output. Power and Performance Specifications RMS Power @ 4Ω Approximately 200 watts x 4 channels at 14.4V RMS Power @ 2Ω Approximately 350 watts x 4 channels at 14.4V Bridged Power @ 4Ω Approximately 700 watts x 2 channels at 14.4V Frequency Response 20Hz–20kHz +/-3dB THD < 0.5% at 1kHz Signal-to-Noise Ratio Approximately 91dB A-weighted Damping Factor Approximately 200 Crossovers HPF / FULL / LPF, 30Hz–300Hz, 12dB/octave Turn-On Modes REM / DC turn-on support Operating Voltage 8V–16V Current Draw Approximately 70A music / 130A max Recommended Fuse Approximately 150A for music use Best Use for the FLX1400.4 The FLX1400.4 is best used in Harley-Davidson bagger audio builds that need strong 4-channel amplifier power for fairing speakers, saddlebag lid speakers, midbass, or bridged speaker layouts. It is built for riders who want more output without giving up control or clarity. Designed Around Real Motorcycle Audio Motorcycle audio is different from car audio. Wind noise, road speed, speaker placement, electrical load, and limited mounting space all matter. This amplifier belongs in systems where the speaker choice, wiring, fusing, and tuning plan are matched correctly. Recommended System Planning To get the best performance from the Cicada FLX1400.4, match it with the right speakers, proper OFC power and ground wiring, correct battery-side fusing, clean signal input, and a real tuning plan. For Harley-Davidson Touring and custom bagger audio systems, amplifier power should always be planned around the speakers, impedance, charging system, mounting location, and final sound goal. If you are unsure whether this amplifier is the right choice for your Road Glide, Street Glide, CVO, Road King, Indian, or custom motorcycle audio build, contact Garage Bagger Stereo before ordering. Related Cicada & Motorcycle Audio Paths Build the system around the correct amplifier, speakers, DSP, wiring, and installation parts. These related collections help match the FLX1400.4 with the right Harley audio upgrade path. Shop Cicada motorcycle amplifiers for Harley-Davidson audio builds Shop motorcycle amplifiers for Harley bagger audio systems Shop Cicada Audio speakers, amplifiers, DSP, and bagger audio upgrades Shop motorcycle DSP for Harley-Davidson audio tuning Shop motorcycle amplifier installation parts Need Help Choosing the Right Cicada Amplifier? Need help matching the Cicada FLX1400.4 to your speakers, bike, wiring, DSP, or complete Harley audio system? Call Garage Bagger Stereo or start a build consultation and we’ll help match the amplifier power, speaker layout, impedance, and tuning plan to your build. Call 864-334-6131 Start a Build ConsultationSale -
SaleCicada Audio FLX1400.4PRO 1400W 4-Channel DSP Motorcycle Amplifier
Vendor:Cicada AudioCicada Audio FLX1400.4PRO 1400W 4-Channel DSP Motorcycle Amplifier The Cicada Audio FLX1400.4PRO combines a high-output four-channel Class-D motorcycle amplifier with a full six-channel digital signal processor in one compact chassis. It delivers 350 watts RMS per channel at 2 ohms while giving professional installers the crossover, signal-routing and tuning control needed for serious Harley-Davidson, Indian and custom motorcycle audio systems. Four DSP channels feed the amplifier's internal outputs while two additional processed pass-through channels remain available for compatible system expansion. Bluetooth audio streaming, USB-C computer tuning and Cicada's DIALD DSP platform make the FLX1400.4PRO a complete power-and-processing solution for high-output bagger audio. THE REFERENCE STANDARD 1400 Watts of Power with Six-Channel DSP Control Four high-output amplified channels, two processed pass-through outputs and professional DSP control in a compact motorcycle-ready amplifier built for loud, clean highway performance. Start a Build Consultation Call 864-334-6131 FLX1400.4PRO Key Specifications Model FLX1400.4PRO Amplifier Type 4-Channel Class-D Motorcycle Amplifier with Built-In DSP DSP Architecture 6 Channels — 4 Amplified + 2 Pass-Through RMS Power @ 4Ω 225W × 4 @ 14.4V RMS Power @ 2Ω 350W × 4 @ 14.4V Bridged Power @ 4Ω 700W × 2 @ 14.4V Frequency Response 20 Hz – 20 kHz ±3 dB THD + Noise 0.1% @ 2Ω per channel at 10% rated power Signal-to-Noise Ratio 91 dB A-Weighted Damping Factor 200 Total Efficiency 80% Crossover Modes High-Pass / Band-Pass / Low-Pass Crossover Range 20 Hz – 20 kHz Crossover Slopes 6 / 12 / 24 / 48 dB per octave Input Sensitivity 0.2V – 12V Operating Voltage 9V – 16V Current Draw — Music 70A Current Draw — Maximum 150A Recommended Fuse 100A Power Input 4 AWG Speaker Outputs 12 AWG Busbar-Style Terminals Turn-On Modes REM / DC / VOX DSP Connectivity Bluetooth Audio Streaming / USB-C PC Tuning / DIALD DSP Dimensions with Brackets 8.26 × 4.9 × 2 in / 210 × 125 × 51 mm Chassis Dimensions 7.1 × 4.9 × 2 in / 180 × 125 × 51 mm Warranty 2 Years System planning note: Published amplifier output is measured at 14.4 volts. Actual output depends on motorcycle charging voltage, speaker impedance, wiring, electrical capacity, signal level and final DSP configuration. Four Amplified Channels Plus Two DSP Expansion Channels The FLX1400.4PRO is more than a four-channel amplifier. Its integrated DSP provides six processed outputs: four channels feed the internal Class-D amplifier while two additional DSP channels provide processed pass-through outputs for compatible future amplifiers. 225W × 4 @ 4Ω Strong four-channel output for compatible 4-ohm motorcycle speakers, component systems and high-efficiency coaxial configurations. 350W × 4 @ 2Ω Full 1400-watt output for properly configured 2-ohm motorcycle speaker systems requiring serious highway-speed authority. 700W × 2 Bridged The amplifier can be bridged into two compatible 4-ohm loads when the system design requires higher two-channel output. Built-In Six-Channel DSP Motorcycle audio requires more than amplifier power. Speaker location, wind noise, road noise, open-air listening and unequal distances from the rider all affect the final sound. The FLX1400.4PRO integrates the DSP control required to build the system around the motorcycle rather than relying only on basic amplifier controls. Six total DSP channels. Four internally amplified DSP outputs. Two processed pass-through outputs for compatible expansion. High-pass, band-pass and low-pass crossover modes. 20 Hz to 20 kHz crossover adjustment range. 6, 12, 24 and 48 dB-per-octave selectable slopes. Bluetooth audio streaming. USB-C computer tuning. Cicada DIALD PC and app-based DSP configuration. DSP advantage: Power alone does not create a properly tuned motorcycle audio system. Correct crossover points, signal level, output balance and system response are what allow that power to stay controlled and clean. Built for Harley-Davidson Bagger Audio Cicada engineered the FLX1400.4PRO around motorcycle installations, including direct mounting compatibility with compatible Harley-Davidson Road Glide and Street Glide amplifier rack locations. Its compact aluminum chassis delivers serious output without requiring the physical space normally associated with a 1400-watt four-channel amplifier. Road Glide Compact dimensions and multiple mounting options make the FLX1400.4PRO a strong amplifier platform for compatible Road Glide fairing installations. Street Glide Designed to work with compatible Street Glide amplifier rack layouts where mounting space is limited. Custom Baggers High power density and built-in DSP also make it useful for custom Harley-Davidson, Indian and powersports audio systems. Motorcycle-Ready Construction The FLX1400.4PRO uses an extruded aluminum heatsink and a conformal-coated circuit board to improve resistance to the vibration, moisture and dust encountered in motorcycle audio installations. Conformal-coated circuit board. Extruded aluminum amplifier chassis. Cicada ICAD overload protection circuitry. Status and clipping LED indicators. 4 AWG power connections. 12 AWG busbar-style speaker outputs. REM, DC and VOX turn-on modes. Molex input system supporting RCA or compatible Harley-specific termination. Bluetooth Audio and USB-C DIALD Tuning Built-in Bluetooth audio streaming provides a direct playback source for compatible testing, setup and listening. For deeper tuning control, USB-C connectivity allows a computer to connect directly to the amplifier's DSP. Cicada's DIALD platform provides PC and compatible app-based control over the FLX1400.4PRO DSP, giving installers the tools required to configure crossover behavior and system response around the actual motorcycle and speaker layout. Designed for Front, Rear and Component Systems Four high-output amplifier channels make the FLX1400.4PRO suitable for multiple motorcycle audio layouts. It can power front and rear speakers, component networks, saddlebag systems, lowers, fairing speakers or other properly matched combinations. Fairing and saddlebag speaker systems. Front and rear component configurations. 2-ohm high-output motorcycle speakers. 4-ohm coaxial and component systems. Mid-bass and pro-audio motorcycle speaker systems. Systems requiring processed outputs for an additional amplifier. Load planning matters: Always calculate the final impedance presented to each amplifier channel before wiring. Speaker count alone does not determine amplifier load. Electrical System Requirements Cicada specifies approximately 70 amps of music current draw and up to 150 amps maximum for the FLX1400.4PRO, with a recommended 100-amp fuse for the published music-load specification. Use properly sized OFC power and ground wiring. FLX1400.4PRO accepts 4 AWG power connections. Install appropriate battery-side fuse protection. Keep power and ground connections short, clean and secure. Confirm motorcycle battery condition before installation. Evaluate charging-system capacity for sustained high-output operation. Protect all wiring from heat, abrasion, sharp edges and moving components. Plug-and-Play Integration Options Garage Bagger Stereo offers this amplifier with optional bike-specific integration packages for multiple Harley-Davidson Touring generations. Choose the correct option for your motorcycle and radio configuration when ordering. Amplifier only. 2023.5+ Harley A2B integration without an additional external DSP. 2014–2023 Harley Touring with factory radio. 2014–2023 Harley Touring with aftermarket radio. 1998–2013 Harley Touring with factory radio. 1998–2013 Harley Touring with aftermarket radio. The exact harnessing and integration hardware varies by selected motorcycle generation and radio configuration. Verify your year, model, factory audio system and current radio before ordering. Installation and Tuning Verify final speaker impedance before connecting amplifier outputs. Confirm all power, ground and fuse requirements before installation. Mount the amplifier securely with adequate ventilation. Use correct signal integration for the motorcycle's radio and factory audio architecture. Set DSP crossover points around the actual speakers and enclosure configuration. Establish proper gain structure throughout the source, integration device and amplifier. Complete final DSP tuning after the motorcycle is fully assembled. Professional installation and system tuning are strongly recommended for high-output systems. Need Help Matching the FLX1400.4PRO to Your Bike? The right amplifier is only one part of a properly designed motorcycle audio system. Speaker impedance, radio integration, electrical capacity, crossover strategy, mounting location, wiring and DSP tuning all affect the final performance. Tell Garage Bagger Stereo your motorcycle year, model, radio, speakers and performance goal and we can help determine the correct FLX1400.4PRO configuration and integration path. Start a Build Consultation Call 864-334-6131Sale -
SaleCicada Audio FLX1600.1 — Mono Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier — Mono Cicada Audio FLX1600.1 — High-Output Mono Power for Bagger Audio One channel, no compromise. The FLX1600.1 is a mono full-range workhorse for high-output lids, mid-bass, or a compact sub. It packs serious wattage into a compact, bike-ready chassis with HPF/LPF control and clean integration on Harley-Davidson® and Indian® touring platforms. Why Riders Choose It Serious output — up to 1600 × 1 @ 2Ω (14.4V). Compact chassis — 8.6″ × 4.9″ × 2.0″ tucks behind fairings/bags. Bike-ready — element-ready design for motorcycle use. Flexible turn-on — REM / DC integration. On-board crossovers — HPF 10–80 Hz; LPF 80 Hz–20 kHz, 12 dB/oct. Shop Motorcycle Amplifiers Best With High-output lids or mid-bass at 2–4Ω Compact 4Ω subwoofer (enable LPF) OFC wiring & correct fusing; careful gain setup Factory radio or DSP front-end Tell us your bike and speakers — we’ll map crossovers, slopes, and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 670 × 1 / 950 × 1 RMS Power @ 2Ω (12.5V / 14.4V) 1250 × 1 / 1600 × 1 Frequency Response 10 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 86 dB / 200 Crossovers HPF 10–80 Hz; LPF 80 Hz–20 kHz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 9 – 16 V Current Draw (Music / Max) 70 A / 140 A Recommended Fuse (Music) 100 A Efficiency ~80% Gain Range 0.2 – 12 V Dimensions (L × W × H) 8.6″ × 4.9″ × 2.0″ (218 × 124 × 51 mm) Specs from Cicada’s product page; multiple dealers corroborate power ratings and crossover ranges. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Is this for subs or mids? Both. It’s a mono full-range design. Use HPF for mid-bass/lids or LPF for a compact sub. We’ll help you choose the right filter points. Will it work with my factory radio? Yes — use DC or REM turn-on and set gains carefully. Add DSP if you need advanced EQ or time alignment. What wiring and fuse should I use? Use OFC wire sized for current draw and fuse at the battery (100 A music). Keep grounds short with solid chassis bonding. Is it motorcycle-ready? Yes — element-ready construction. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX2000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioCicada Audio FLX2000.4 is a compact high-output four-channel motorcycle amplifier designed for Harley-Davidson, bagger, powersports, and custom audio systems. It delivers up to 542 watts RMS per channel at 2 ohms at 14.4 volts, supports 2-ohm and 4-ohm speaker systems, and provides bridgeable power, onboard crossover control, and motorcycle-ready construction for clean highway-speed output. Cicada Audio FLX2000.4 2000W 4-Channel Motorcycle Amplifier The Cicada Audio FLX2000.4 is a compact high-output 4-channel motorcycle amplifier built for Harley-Davidson bagger audio systems that need serious power, clean control, and highway-speed volume. With strong output at 2Ω and 4Ω, bridgeable power, onboard crossover control, and motorcycle-ready construction, the FLX2000.4 is built for riders who want more speaker authority without adding oversized amplifier hardware. Cicada Amplifiers Motorcycle Amplifiers Shop Cicada Audio THE REFERENCE STANDARD Big 4-Channel Power for Harley Bagger Audio Built for high-output Harley audio systems that need compact amplifier power, clean tuning control, 2Ω/4Ω speaker support, and serious open-air performance. Start a Build Consultation Call 864-334-6131 Key Product Details Product Cicada Audio FLX2000.4 2000W 4-Channel Motorcycle Amplifier Amplifier Type High-output 4-channel motorcycle amplifier Best For Harley-Davidson bagger audio, fairing speakers, saddlebag lid speakers, midbass, bridged speaker pairs, and high-output amplified motorcycle systems System Goal More power, stronger speaker control, louder open-air output, cleaner tuning, and better highway-speed performance Speaker Support 2Ω and 4Ω speaker systems, depending on final wiring and system design Install Focus Compact motorcycle amplifier layout for Harley-Davidson Touring, Road Glide, Street Glide, CVO, Indian, and custom bagger audio builds Always verify speaker impedance, wiring layout, fuse size, amplifier placement, gain structure, charging system capacity, and final system design before ordering or installing this amplifier. Built for Serious Harley-Davidson Audio Power The Cicada FLX2000.4 is made for riders who need more than basic motorcycle amplifier power. It is designed to drive upgraded 6.5" speakers, 6x9 speakers, pro coaxials, saddlebag lid speakers, midbass drivers, or bridged 4Ω speaker pairs with serious output and control. In a properly planned Harley-Davidson bagger audio system, the FLX2000.4 can support aggressive front and rear speaker layouts, bridged midbass power, or full custom speaker systems where clean volume and highway-speed performance are the priority. Power and Performance Specifications RMS Power @ 4Ω 275 watts x 4 channels at 12.5V / 331 watts x 4 channels at 14.4V RMS Power @ 2Ω 450 watts x 4 channels at 12.5V / 542 watts x 4 channels at 14.4V Bridged Power @ 4Ω 866 watts x 2 channels at 12.5V / 1044 watts x 2 channels at 14.4V Frequency Response 20Hz–20kHz +/-3dB THD < 0.5% at 1kHz Signal-to-Noise Ratio 91dB A-weighted Damping Factor 200 Crossovers HPF / FULL / LPF, 30Hz–300Hz, 12dB/octave Turn-On Modes REM / DC turn-on support Operating Voltage 8V–16V Current Draw 60A music / 240A max Recommended Fuse 120A for music use Efficiency Approximately 79% Gain Range 0.2V–12V Dimensions 8.6" x 4.9" x 2.0" / 218mm x 124mm x 51mm Best Use for the FLX2000.4 The FLX2000.4 is best used in Harley-Davidson and custom bagger audio builds that need strong 4-channel amplifier power for fairing speakers, saddlebag lid speakers, midbass, or bridged speaker pairs. Designed Around Real Motorcycle Audio Motorcycle audio is different from car audio. Wind noise, road speed, speaker placement, electrical load, limited mounting space, and heat management all matter. This amplifier belongs in systems where the speakers, wiring, fusing, and tuning plan are matched correctly. Recommended System Planning To get the best performance from the Cicada FLX2000.4, match it with the right speakers, proper OFC power and ground wiring, correct battery-side fusing, clean signal input, and a real tuning plan. For Harley-Davidson Touring and custom bagger audio systems, amplifier power should always be planned around the speakers, impedance, charging system, mounting location, and final sound goal. If you are unsure whether this amplifier is the right choice for your Road Glide, Street Glide, CVO, Road King, Indian, or custom motorcycle audio build, contact Garage Bagger Stereo before ordering. Related Cicada & Motorcycle Audio Paths Build the system around the correct amplifier, speakers, DSP, wiring, and installation parts. These related collections help match the FLX2000.4 with the right Harley audio upgrade path. Shop Cicada motorcycle amplifiers for Harley-Davidson audio builds Shop motorcycle amplifiers for Harley bagger audio systems Shop Cicada Audio speakers, amplifiers, DSP, and bagger audio upgrades Shop motorcycle DSP for Harley-Davidson audio tuning Shop motorcycle amplifier installation parts Need Help Choosing the Right Cicada Amplifier? Need help matching the Cicada FLX2000.4 to your speakers, bike, wiring, DSP, or complete Harley audio system? Call Garage Bagger Stereo or start a build consultation and we’ll help match the amplifier power, speaker layout, impedance, wiring, and tuning plan to your build. Call 864-334-6131 Start a Build ConsultationSale -
SaleCicada Audio FLX2500.1 — Mono Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier — Mono Cicada Audio FLX2500.1 — High-Output Mono Power for Bagger Audio One channel, maximum punch. The FLX2500.1 is a mono full-range workhorse for high-output lids, mid-bass, or a compact sub. It packs big wattage into a compact, bike-ready chassis, with HPF/LPF control and clean integration on Harley-Davidson® and Indian® touring platforms. Why Riders Choose It Serious output — up to 2500 × 1 @ 2Ω (14.4V). Compact chassis — 9.2″ × 4.9″ × 2.0″ tucks behind fairings/bags. Bike-ready — element-ready design for motorcycles. Flexible turn-on — REM / DC integration. On-board crossovers — HPF 10–80 Hz; LPF 80 Hz–20 kHz, 12 dB/oct. Cicada recommends a lithium battery upgrade and 2 AWG power wire for this model. Best With High-output lids or mid-bass at 2–4Ω Compact 4Ω subwoofer (enable LPF) OFC wiring & correct fusing; careful gain setup Factory radio or DSP front-end Tell us your bike and speakers — we’ll map crossovers, slopes, and gains for loud, clean highway performance. Key Specifications RMS Power @ 2Ω (14.4V) 2500 × 1 Frequency Response 10 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% @ 10% rated power) SNR (A-wt) / Damping Factor 86 dB / 200 Crossovers HPF 10–80 Hz; LPF 80 Hz–20 kHz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 9 – 16 V Current Draw (Music / Max) 80 A / 260 A Recommended Fuse (Music) 150 A Total Efficiency ~80% Gain Range 0.2 – 12 V Dimensions (L × W × H) 9.2″ × 4.9″ × 2.0″ (234 × 124 × 51 mm) Specs pulled from Cicada’s official page; multiple dealers corroborate power, dimensions, and fuse guidance. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Is this for subs or mids? Both. It’s a mono full-range design. Use HPF for mid-bass/lids or LPF for a compact sub. We’ll help you choose the right filter points. Will it work with my factory radio? Yes — use DC or REM turn-on and set gains carefully. Add DSP if you need advanced EQ or time alignment. What wiring and battery should I use? Run 2 AWG power, fuse at the battery (150 A music), and use a lithium battery upgrade as recommended by Cicada. Is it motorcycle-ready? Yes — element-ready construction. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX700.4 Motorcycle Amplifier
Vendor:Cicada AudioCicada Audio FLX700.4 4-Channel Motorcycle Amplifier The Cicada Audio FLX700.4 is a compact 4-channel motorcycle amplifier built for Harley-Davidson and Indian touring audio systems that need clean power, efficient output, and reliable highway-speed performance. With up to 175 watts x 4 at 2Ω, onboard crossover control, REM/DC turn-on, and a small motorcycle-ready chassis, the FLX700.4 is a strong fit for fairing speakers, saddlebag lid speakers, and clean amplified bagger audio builds. Cicada Amplifiers Motorcycle Amplifiers Shop Cicada Audio THE REFERENCE STANDARD Compact 4-Channel Power for Harley Audio Built for riders who need clean motorcycle amplifier power, compact installation, 2Ω/4Ω speaker support, and dependable output for real bagger audio systems. Start a Build Consultation Call 864-334-6131 Key Product Details Product Cicada Audio FLX700.4 4-Channel Motorcycle Amplifier Amplifier Type Compact 4-channel motorcycle amplifier Best For Harley-Davidson and Indian touring audio systems, fairing speakers, saddlebag lid speakers, coaxial speakers, and clean amplified motorcycle audio builds System Goal Clean power, stronger speaker output, better clarity, compact installation, and louder highway-speed performance Speaker Support 2Ω and 4Ω speaker systems, depending on final wiring and system design Install Focus Compact motorcycle amplifier layout for Harley-Davidson Touring, Road Glide, Street Glide, CVO, Indian, and custom bagger audio systems Always verify speaker impedance, wiring layout, fuse size, amplifier placement, gain structure, charging system capacity, and final system design before ordering or installing this amplifier. Built for Clean Harley-Davidson and Indian Audio Power The Cicada FLX700.4 is built for riders who want a clean, compact amplifier upgrade without overcomplicating the system. It gives Harley-Davidson and Indian touring motorcycles the power needed to run upgraded motorcycle-specific speakers with better clarity, stronger output, and more control than factory power alone. This amplifier is a strong choice for riders powering front fairing speakers, rear speakers, saddlebag lid speakers, or a balanced 4-channel motorcycle audio system. When matched with the right speakers, wiring, and tuning, the FLX700.4 helps the system stay cleaner and louder at speed. Power and Performance Specifications Channels 4 RMS Power @ 4Ω 125 watts x 4 channels RMS Power @ 2Ω 175 watts x 4 channels Bridged Power @ 4Ω 350 watts x 2 channels Crossovers HPF / LPF / FULL, 30Hz–300Hz Signal-to-Noise Ratio 95dB THD <0.1% Operating Voltage 8V–16V Fuse Rating 60A total, 2 x 30A Dimensions 11.5" x 5.1" x 1.8" Best Use for the FLX700.4 The FLX700.4 is best used in Harley-Davidson and Indian bagger audio builds that need compact 4-channel amplifier power for fairing speakers, rear speakers, saddlebag lid speakers, or efficient coaxial speaker systems. Designed Around Real Motorcycle Audio Motorcycle audio is different from car audio. Wind noise, road speed, speaker placement, electrical limits, wiring path, and mounting space all matter. This amplifier should be matched with the correct speaker load, clean wiring, and a proper tuning plan. Recommended System Planning To get the best performance from the Cicada FLX700.4, match it with efficient motorcycle-specific speakers, proper OFC power and ground wiring, correct battery-side fusing, clean signal input, and a real tuning plan. For Harley-Davidson Touring, Indian touring, and custom bagger audio systems, amplifier power should always be planned around the speakers, impedance, charging system, mounting location, and final sound goal. If you are unsure whether this amplifier is the right choice for your Road Glide, Street Glide, CVO, Road King, Indian, or custom motorcycle audio build, contact Garage Bagger Stereo before ordering. Related Cicada & Motorcycle Audio Paths Build the system around the correct amplifier, speakers, DSP, wiring, and installation parts. These related collections help match the FLX700.4 with the right Harley or Indian audio upgrade path. Shop Cicada motorcycle amplifiers for Harley-Davidson audio builds Shop motorcycle amplifiers for Harley bagger audio systems Shop Cicada Audio speakers, amplifiers, DSP, and bagger audio upgrades Shop motorcycle DSP for Harley-Davidson audio tuning Shop motorcycle amplifier installation parts Need Help Choosing the Right Cicada Amplifier? Need help matching the Cicada FLX700.4 to your speakers, bike, wiring, DSP, or complete Harley audio system? Call Garage Bagger Stereo or start a build consultation and we’ll help match the amplifier power, speaker layout, impedance, wiring, and tuning plan to your build. Call 864-334-6131 Start a Build ConsultationSale -
SaleDavidson Audio 8" Indian Motorcycle Lids Without Tweeters
Vendor:Davidson AudioIndian Motorcycle 8" Saddlebag Speaker Lids Davidson Audio 8' Audio Lids for 2019-current Indian Challenger or 2019-current Indian Chieftain square-style bags. 10-15 business day lead time Modification may be required Body part sales are finalSale -
Davidson Audio Indian Challenger/Pursuit Fairing Amp/DSP Plate
Vendor:Davidson AudioIndian Challenger/Pursuit Fairing Amp/DSP Plate This product is compatible with the 2020+ Indian Challenger & Pursuit. Custom-designed AMP & DSP mounting plates allow you to install an amplifier or DSP in the factory power unit location in the fairing. These mounting plates are designed to fit the following Amplifiers: Soundigital 400.4EVOX2, 800.4EVOX2, 800.1EVOPS, & 800.4EVOPS. These mounting plates were designed to provide the following DSP's Rockford DSR-1 & HKI Mini.
Indian Motorcycle Audio
Indian motorcycle audio systems require platform-specific engineering to perform correctly at speed. This collection is built for Indian touring motorcycles, including Chieftain, Roadmaster, Challenger, and other bagger platforms where proper fitment, signal control, and power management are critical.
Unlike universal motorcycle audio solutions, the products in this collection are selected specifically for Indian motorcycle architecture. That includes speaker fitment constraints, fairing acoustics, saddlebag geometry, and electrical system limitations unique to Indian touring platforms.
This collection supports complete system builds and staged upgrades, including:
- Fairing speakers designed for Indian-specific mounting locations
- Saddlebag speaker lids for rear audio expansion
- Motorcycle amplifiers sized and tuned for Indian touring applications
- DSP processors for signal correction, time alignment, and tuning
- Installation parts engineered for clean, serviceable installs
Indian motorcycles benefit significantly from proper signal management and amplification. Factory audio systems are limited in output and tuning control, making DSP integration and dedicated amplification essential for achieving clean volume and consistent clarity at highway speeds.
All components in this collection are vetted for compatibility with professional installation standards, ensuring proper impedance matching, thermal stability, and long-term reliability in motorcycle environments.
This page serves as the foundation for Indian motorcycle audio builds ranging from simple speaker upgrades to full multi-amplifier, DSP-controlled systems.