-
Arc Audio PSM Pro Digital Sound Processor | Plug and Play
Vendor:Arc AudioHarley Davidson Minature Pro Digital Sound Processor Plug and Play for stock radios 14-23 Harley Davidson Models Plug and Play for stock radios and amps 23 CVO to current Harley Davidson Models The ARC Audio PSM Pro digital sound processor is a small but powerful device designed to enhance the audio quality of your car or motorcycle's sound system. It is an upgraded version of the PSM offering even better performance and 8 output channels.The PSM Pro uses advanced 32-bit DSP technology and has 296 total bands of full variable parametric equalization, open architecture crossover selection, signal delay, and phase control. This allows you to tune your audio system to your specific preferences and improve the quality of your listening experience. Processor Type Stand Alone Unit Processor Resolution 32-Bits Sample Rate 96kHz Analog Inputs 6 CH. Differential in (RCA or Speaker Level) Input Sensitivity 2V - 16V RMS Digital Inputs Coaxial Auto-sense Turn-On DC (BTL) (Uses Ch 1/2 Inputs Only) Outputs (RCA) 8-Channels Outputs Voltage (RCA) Up to 3.5V Input Impedance (RCA) 10k ohms Frequency Response 20Hz - 23.5kHz S/N Ratio 1V 1:1 86dB S/N 4V 1:1 90dB Operating Voltage 6V - 17.0V (Start Stop Compliance to 4.5V) Output Equalization 31 Band + 6 (37 Band) X 8 Parametric EQ, Highpass Shelf, Lowpass Shelf, 1st & 2nd order Allpass. (296 Total Bands Output Equalization Resolution 0.01dB dB per step +18dB / -24dB Output Signal Delay Up to 30ms per channel in .01ms increments (Fixed Point Delay) Input Signal Mixer Yes - 8-Channels In (Including Digital) x 8-Channels Out Advanced Mixer (Output Signal Mixer) Yes Easy-to-use Mixer Assistant Yes Crossovers Phase Correct AP/HP/LP/BP all channels Crossover Slopes 6dB, 12dB, 18dB, 24dB, 30dB, 36dB, 42dB, 48dB Slopes all bands all channels Crossover Types Butterworth, Linkwitz-Riley, Bessel, Variable Q, Chebyshev (all channels all bands) Crossover selectable frequencies 10Hz - 20kHz in 0.1 Hz increments) Output Signal up mixer Yes Input Signal Equalization 12 Bands Parametric (linkable) Per Channel Input Equalization Resolution 1/10th dB per step +18dB / -24dB Input Equalization All Pass Filters Yes - Individual per input EQ band Input Signal Delay Yes - Up to 11.04ms per channel input Presets Up to 4-Presets External Remote Level Control Yes (LR1 Sold Separately) AXP WiFi control adapter card No Preset selection without controller use Yes - Optional manual trigger switches +/- for up to 4 presets (Not Included) Remote Turn-On Output Controls Turn on Output (up to 40ms), Turn-on Hold (up to 40ms), Auto-sense hold time (up to 200ms) Remote Turn-On Output On/Off lead timing control Remote on/off adjustable up to 40 seconds each Maestro AR Module interface capable Yes - Requires Maestro T-Harness, and data cable for connection. Expansion Capability PSM-Pro can be run in multiples with individual USB connections to a single PC with single operating software being used Software Interface 64 bit Windows 8, Windows 8.1 or Windows 10 Dimensions 3.75"(L) x 3.0"(W) x 1.35"(H) -
SaleCicada Audio CHX525 5.25" Pro Coaxial Speaker (Pair)
Vendor:Cicada AudioCHX525.2 or .4Ω HIGH-PERFORMANCE PRO COAX HORN SPEAKERS New to our pro-line horn series, the CHX525.2 5.25″ coax horn speaker features a 1.5″, 2Ω, voice coil woofer and a 1.0″ horn, 8Ω, tweeter. It handles big power and is high-performance. 150w RMS / 300w MAX Power Handling each Heavy duty diecast basket 1.5″ high temp voice coil for mid-bass 1.0″ high temp voice coil for tweeter Freq Response: 90Hz – 20kHz +/- 5dB 91dB Sensitivity External 12dB / 6kHz tweeter crossover Mounting Depth: 2.26″ / 70mm Mounting Diameter: 5.25″ / 133mmSale -
SaleCicada Audio FLX1000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1000.4 — Compact 4-Channel Power for Bagger Audio Big output in a small chassis. The FLX1000.4 feeds your front + rear speakers real power from a palm-size, bike-ready amp. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a favorite for Harley-Davidson® and Indian® builds that need highway-clear sound without bulky gear. Why Riders Choose It Serious output — up to 254×4 @ 2Ω or 530×2 bridged @ 4Ω (14.4V). Compact chassis — 6.0″ × 4.9″ × 2.0″ fits behind fairings or in bags. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC options for easy integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring with correct fusing and clean grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 150 × 4 / 168 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 220 × 4 / 254 × 4 Bridged @ 4Ω (12.5V / 14.4V) 461 × 2 / 530 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) 60 A / 116 A Recommended Fuse (Music) 120 A Efficiency ~79% Dimensions (L × W × H) 6.0″ × 4.9″ × 2.0″ (152 × 124 × 51 mm) Specs from Cicada’s product page; retailer listings corroborate ratings and dimensions. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Can it run fronts and lids with one amp? Yes — many builds run four channels at 2–4Ω. Use HPF/LPF and proper gains for clean balance. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. Can I bridge it for more power? Yes — bridge pairs at 4Ω for up to ~530 W × 2 (14.4V). Use LPF for mid-bass or small sub duty. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (120 A music rec.). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX1400.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1400.4 — High-Output 4-Channel Power for Bagger Audio More headroom, same compact footprint. The FLX1400.4 drives front + rear speakers with authority from a bike-ready chassis that tucks neatly behind fairings or in bags. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a go-to for Harley-Davidson® and Indian® builds that demand highway-clear output. This amplifier is part of our Motorcycle Amplifiers collection, built for Harley Davidson and Indian touring motorcycles. Why Riders Choose It Serious output — four strong channels or bridged pairs for lids/mid-bass. Compact chassis — mounts cleanly on touring platforms. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring, correct fusing, and solid grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (14.4V) ≈ 200 × 4 RMS Power @ 2Ω (14.4V) ≈ 350 × 4 Bridged @ 4Ω (14.4V) ≈ 700 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor ≈ 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) ≈ 70 A / 130 A Recommended Fuse (Music) ≈ 150 A Dimensions Compact motorcycle-grade chassis Always verify impedance, wiring, and fuse size for your exact setup. Frequently Asked Questions — Motorcycle Audio Can it power fronts and lids cleanly? Yes — run four channels at 2–4Ω for a balanced system, or bridge pairs at 4Ω for more output to lids or mid-bass. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (≈150 A music). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX1400.4P — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1400.4P — High-Output 4-Channel Power for Bagger Audio More headroom, same compact footprint. The FLX1400.4P drives front + rear speakers with authority from a bike-ready chassis that tucks neatly behind fairings or in bags. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a go-to for Harley-Davidson® and Indian® builds that demand highway-clear output. Why Riders Choose It Serious output — four strong channels or bridged pairs for lids/mid-bass. Compact chassis — mounts cleanly on touring platforms. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring, correct fusing, and solid grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (14.4V) ≈ 200 × 4 RMS Power @ 2Ω (14.4V) ≈ 350 × 4 Bridged @ 4Ω (14.4V) ≈ 700 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor ≈ 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) ≈ 70 A / 130 A Recommended Fuse (Music) ≈ 150 A Dimensions Compact motorcycle-grade chassis Always verify impedance, wiring, and fuse size for your exact setup. Frequently Asked Questions — Motorcycle Audio Can it power fronts and lids cleanly? Yes — run four channels at 2–4Ω for a balanced system, or bridge pairs at 4Ω for more output to lids or mid-bass. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (≈150 A music). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX1600.1 — Mono Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier — Mono Cicada Audio FLX1600.1 — High-Output Mono Power for Bagger Audio One channel, no compromise. The FLX1600.1 is a mono full-range workhorse for high-output lids, mid-bass, or a compact sub. It packs serious wattage into a compact, bike-ready chassis with HPF/LPF control and clean integration on Harley-Davidson® and Indian® touring platforms. Why Riders Choose It Serious output — up to 1600 × 1 @ 2Ω (14.4V). Compact chassis — 8.6″ × 4.9″ × 2.0″ tucks behind fairings/bags. Bike-ready — element-ready design for motorcycle use. Flexible turn-on — REM / DC integration. On-board crossovers — HPF 10–80 Hz; LPF 80 Hz–20 kHz, 12 dB/oct. Shop Motorcycle Amplifiers Best With High-output lids or mid-bass at 2–4Ω Compact 4Ω subwoofer (enable LPF) OFC wiring & correct fusing; careful gain setup Factory radio or DSP front-end Tell us your bike and speakers — we’ll map crossovers, slopes, and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 670 × 1 / 950 × 1 RMS Power @ 2Ω (12.5V / 14.4V) 1250 × 1 / 1600 × 1 Frequency Response 10 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 86 dB / 200 Crossovers HPF 10–80 Hz; LPF 80 Hz–20 kHz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 9 – 16 V Current Draw (Music / Max) 70 A / 140 A Recommended Fuse (Music) 100 A Efficiency ~80% Gain Range 0.2 – 12 V Dimensions (L × W × H) 8.6″ × 4.9″ × 2.0″ (218 × 124 × 51 mm) Specs from Cicada’s product page; multiple dealers corroborate power ratings and crossover ranges. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Is this for subs or mids? Both. It’s a mono full-range design. Use HPF for mid-bass/lids or LPF for a compact sub. We’ll help you choose the right filter points. Will it work with my factory radio? Yes — use DC or REM turn-on and set gains carefully. Add DSP if you need advanced EQ or time alignment. What wiring and fuse should I use? Use OFC wire sized for current draw and fuse at the battery (100 A music). Keep grounds short with solid chassis bonding. Is it motorcycle-ready? Yes — element-ready construction. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX2000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX2000.4 — Compact 4-Channel Power for Bagger Audio Big-boy power, small footprint. The FLX2000.4 drives front + rear speakers with serious output from a compact, bike-ready chassis. With HPF/LPF crossovers, REM/DC turn-on, and clean tuning, it’s built for Harley-Davidson® and Indian® touring systems that need highway-clear volume without bulky gear. This amplifier is part of our Motorcycle Amplifiers collection, built for Harley Davidson and Indian touring motorcycles. Why Riders Choose It Serious output — up to 542×4 @ 2Ω or 1044×2 bridged @ 4Ω (14.4V). Compact chassis — 8.6″ × 4.9″ × 2.0″ tucks behind fairings/bags. Bike-ready — conformal-coated PCB, designed for motorcycles. Flexible turn-on — REM / DC integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring with 4 AWG power & correct fusing Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 275 × 4 / 331 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 450 × 4 / 542 × 4 Bridged @ 4Ω (12.5V / 14.4V) 866 × 2 / 1044 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) 60 A / 240 A Recommended Fuse (Music) 120 A Efficiency ~79% Gain Range 0.2 – 12 V Dimensions (L × W × H) 8.6″ × 4.9″ × 2.0″ (218 × 124 × 51 mm) Specs from Cicada’s product page and manual; multiple dealers corroborate power ratings and crossover ranges. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Can it run fronts and lids with one amp? Yes — many builds run four channels at 2–4Ω. Use HPF/LPF and proper gains for clean balance. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. Can I bridge it for more power? Yes — bridge pairs at 4Ω for up to ~1044 W × 2 (14.4V). Use LPF for mid-bass duty as needed. What wiring and fuse do I need? Use OFC power/ground with 4 AWG power and fuse at the battery (120 A music). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes with conformal-coated PCB. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
SaleCicada Audio FLX2500.1 — Mono Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier — Mono Cicada Audio FLX2500.1 — High-Output Mono Power for Bagger Audio One channel, maximum punch. The FLX2500.1 is a mono full-range workhorse for high-output lids, mid-bass, or a compact sub. It packs big wattage into a compact, bike-ready chassis, with HPF/LPF control and clean integration on Harley-Davidson® and Indian® touring platforms. Why Riders Choose It Serious output — up to 2500 × 1 @ 2Ω (14.4V). Compact chassis — 9.2″ × 4.9″ × 2.0″ tucks behind fairings/bags. Bike-ready — element-ready design for motorcycles. Flexible turn-on — REM / DC integration. On-board crossovers — HPF 10–80 Hz; LPF 80 Hz–20 kHz, 12 dB/oct. Cicada recommends a lithium battery upgrade and 2 AWG power wire for this model. Best With High-output lids or mid-bass at 2–4Ω Compact 4Ω subwoofer (enable LPF) OFC wiring & correct fusing; careful gain setup Factory radio or DSP front-end Tell us your bike and speakers — we’ll map crossovers, slopes, and gains for loud, clean highway performance. Key Specifications RMS Power @ 2Ω (14.4V) 2500 × 1 Frequency Response 10 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% @ 10% rated power) SNR (A-wt) / Damping Factor 86 dB / 200 Crossovers HPF 10–80 Hz; LPF 80 Hz–20 kHz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 9 – 16 V Current Draw (Music / Max) 80 A / 260 A Recommended Fuse (Music) 150 A Total Efficiency ~80% Gain Range 0.2 – 12 V Dimensions (L × W × H) 9.2″ × 4.9″ × 2.0″ (234 × 124 × 51 mm) Specs pulled from Cicada’s official page; multiple dealers corroborate power, dimensions, and fuse guidance. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Is this for subs or mids? Both. It’s a mono full-range design. Use HPF for mid-bass/lids or LPF for a compact sub. We’ll help you choose the right filter points. Will it work with my factory radio? Yes — use DC or REM turn-on and set gains carefully. Add DSP if you need advanced EQ or time alignment. What wiring and battery should I use? Run 2 AWG power, fuse at the battery (150 A music), and use a lithium battery upgrade as recommended by Cicada. Is it motorcycle-ready? Yes — element-ready construction. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131. We’ll map gains, filters, and wiring for your exact setup.Sale -
Sale -
SaleDavidson Audio 8" Indian Motorcycle Lids Without Tweeters
Vendor:Davidson AudioIndian Motorcycle 8" Saddlebag Speaker Lids Davidson Audio 8' Audio Lids for 2019-current Indian Challenger or 2019-current Indian Chieftain square-style bags. 10-15 business day lead time Modification may be required Body part sales are finalSale -
SaleDavidson Audio Indian Challenger/Pursuit Fairing Speaker Wire Harness
Vendor:Davidson AudioIndian Challenger or Pursuit Fairing Speaker Wire Harness Custom-made fairing speaker wire harness specifically designed for the Indian Challenger/Pursuit platform. This harness provides the necessary connection from your aftermarket amplifier to your aftermarket speaker. We offer two variations of our fairing speaker wiring harness Passive and Active. Passive Speaker Wiring: Single run 100% OFC speaker wire Connection from fairing-mounted amplifier to fairing-mounted speakers Pre-sized, loomed, and color-correlated harness for clutch and brake side Active Speaker Wiring: Dual run 100% OFC speaker wire Connection from fairing-mounted amplifier to fairing-mounted speakers Pre-sized, loomed, and color-correlated harness for clutch and brake side Custom-Made Parts Typically take 5-7 Business DaysSale -
SaleDavidson Audio Indian Challenger/Pursuit Lower Fairing Harness
Vendor:Davidson AudioIndian Challenger or Pursuit Lower Fairing Harness Custom-made Lower Fairing Wire Harness specifically designed for the Indian Challenger/Pursuit platform. This harness provides the necessary connection from your aftermarket amplifier to your aftermarket speaker. Passive Lower Fairing Harness Wiring: Single run 100% OFC speaker wire Weatherproof Deutsch connectors Connection from the fairing-mounted amplifier to lower fairing-mounted speakers Pre-sized, loomed, and color corelated harness for clutch and brake side Custom-Made Parts Typically take 5-7 Business DaysSale
-
Arc Audio PSM Pro Digital Sound Processor | Plug and Play
Vendor:Arc AudioHarley Davidson Minature Pro Digital Sound Processor Plug and Play for stock radios 14-23 Harley Davidson Models Plug and Play for stock radios and amps 23 CVO to current Harley Davidson Models The ARC Audio PSM Pro digital sound processor is a small but powerful device designed to enhance the audio quality of your car or motorcycle's sound system. It is an upgraded version of the PSM offering even better performance and 8 output channels.The PSM Pro uses advanced 32-bit DSP technology and has 296 total bands of full variable parametric equalization, open architecture crossover selection, signal delay, and phase control. This allows you to tune your audio system to your specific preferences and improve the quality of your listening experience. Processor Type Stand Alone Unit Processor Resolution 32-Bits Sample Rate 96kHz Analog Inputs 6 CH. Differential in (RCA or Speaker Level) Input Sensitivity 2V - 16V RMS Digital Inputs Coaxial Auto-sense Turn-On DC (BTL) (Uses Ch 1/2 Inputs Only) Outputs (RCA) 8-Channels Outputs Voltage (RCA) Up to 3.5V Input Impedance (RCA) 10k ohms Frequency Response 20Hz - 23.5kHz S/N Ratio 1V 1:1 86dB S/N 4V 1:1 90dB Operating Voltage 6V - 17.0V (Start Stop Compliance to 4.5V) Output Equalization 31 Band + 6 (37 Band) X 8 Parametric EQ, Highpass Shelf, Lowpass Shelf, 1st & 2nd order Allpass. (296 Total Bands Output Equalization Resolution 0.01dB dB per step +18dB / -24dB Output Signal Delay Up to 30ms per channel in .01ms increments (Fixed Point Delay) Input Signal Mixer Yes - 8-Channels In (Including Digital) x 8-Channels Out Advanced Mixer (Output Signal Mixer) Yes Easy-to-use Mixer Assistant Yes Crossovers Phase Correct AP/HP/LP/BP all channels Crossover Slopes 6dB, 12dB, 18dB, 24dB, 30dB, 36dB, 42dB, 48dB Slopes all bands all channels Crossover Types Butterworth, Linkwitz-Riley, Bessel, Variable Q, Chebyshev (all channels all bands) Crossover selectable frequencies 10Hz - 20kHz in 0.1 Hz increments) Output Signal up mixer Yes Input Signal Equalization 12 Bands Parametric (linkable) Per Channel Input Equalization Resolution 1/10th dB per step +18dB / -24dB Input Equalization All Pass Filters Yes - Individual per input EQ band Input Signal Delay Yes - Up to 11.04ms per channel input Presets Up to 4-Presets External Remote Level Control Yes (LR1 Sold Separately) AXP WiFi control adapter card No Preset selection without controller use Yes - Optional manual trigger switches +/- for up to 4 presets (Not Included) Remote Turn-On Output Controls Turn on Output (up to 40ms), Turn-on Hold (up to 40ms), Auto-sense hold time (up to 200ms) Remote Turn-On Output On/Off lead timing control Remote on/off adjustable up to 40 seconds each Maestro AR Module interface capable Yes - Requires Maestro T-Harness, and data cable for connection. Expansion Capability PSM-Pro can be run in multiples with individual USB connections to a single PC with single operating software being used Software Interface 64 bit Windows 8, Windows 8.1 or Windows 10 Dimensions 3.75"(L) x 3.0"(W) x 1.35"(H) -
Sale
Cicada Audio CHX525 5.25" Pro Coaxial Speaker (Pair)
Vendor:Cicada AudioCHX525.2 or .4Ω HIGH-PERFORMANCE PRO COAX HORN SPEAKERS New to our pro-line horn series, the CHX525.2 5.25″ coax horn speaker features a 1.5″, 2Ω, voice coil woofer and a 1.0″ horn, 8Ω, tweeter. It handles big power and is high-performance. 150w RMS / 300w MAX Power Handling each Heavy duty diecast basket 1.5″ high temp voice coil for mid-bass 1.0″ high temp voice coil for tweeter Freq Response: 90Hz – 20kHz +/- 5dB 91dB Sensitivity External 12dB / 6kHz tweeter crossover Mounting Depth: 2.26″ / 70mm Mounting Diameter: 5.25″ / 133mmSale -
Sale
Cicada Audio FLX1000.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1000.4 — Compact 4-Channel Power for Bagger Audio Big output in a small chassis. The FLX1000.4 feeds your front + rear speakers real power from a palm-size, bike-ready amp. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a favorite for Harley-Davidson® and Indian® builds that need highway-clear sound without bulky gear. Why Riders Choose It Serious output — up to 254×4 @ 2Ω or 530×2 bridged @ 4Ω (14.4V). Compact chassis — 6.0″ × 4.9″ × 2.0″ fits behind fairings or in bags. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC options for easy integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring with correct fusing and clean grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (12.5V / 14.4V) 150 × 4 / 168 × 4 RMS Power @ 2Ω (12.5V / 14.4V) 220 × 4 / 254 × 4 Bridged @ 4Ω (12.5V / 14.4V) 461 × 2 / 530 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) 60 A / 116 A Recommended Fuse (Music) 120 A Efficiency ~79% Dimensions (L × W × H) 6.0″ × 4.9″ × 2.0″ (152 × 124 × 51 mm) Specs from Cicada’s product page; retailer listings corroborate ratings and dimensions. Always verify wiring/impedance before power-on. Frequently Asked Questions — Motorcycle Audio Can it run fronts and lids with one amp? Yes — many builds run four channels at 2–4Ω. Use HPF/LPF and proper gains for clean balance. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. Can I bridge it for more power? Yes — bridge pairs at 4Ω for up to ~530 W × 2 (14.4V). Use LPF for mid-bass or small sub duty. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (120 A music rec.). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale -
Sale
Cicada Audio FLX1400.4 — 4‑Channel Motorcycle Amplifier
Vendor:Cicada AudioMotorcycle Amplifier Cicada Audio FLX1400.4 — High-Output 4-Channel Power for Bagger Audio More headroom, same compact footprint. The FLX1400.4 drives front + rear speakers with authority from a bike-ready chassis that tucks neatly behind fairings or in bags. Flexible HPF/LPF crossovers, REM/DC turn-on, and clean tuning make it a go-to for Harley-Davidson® and Indian® builds that demand highway-clear output. This amplifier is part of our Motorcycle Amplifiers collection, built for Harley Davidson and Indian touring motorcycles. Why Riders Choose It Serious output — four strong channels or bridged pairs for lids/mid-bass. Compact chassis — mounts cleanly on touring platforms. Bike-ready — designed for the motorcycle environment. Flexible turn-on — REM / DC integration. On-board crossovers — HPF / FULL / LPF 30–300 Hz, 12 dB/oct. Shop Motorcycle Amplifiers Best With Front & rear speakers at 2–4Ω Bridged 4Ω pairs for lids or mid-bass OFC wiring, correct fusing, and solid grounds Factory radio or DSP — we’ll map gains & filters Tell us your bike and speakers — we’ll set crossover points and gains for loud, clean highway performance. Key Specifications RMS Power @ 4Ω (14.4V) ≈ 200 × 4 RMS Power @ 2Ω (14.4V) ≈ 350 × 4 Bridged @ 4Ω (14.4V) ≈ 700 × 2 Frequency Response 20 Hz – 20 kHz (±3 dB) THD (1 kHz) < 0.5% (≈0.1% at 10% rated power) SNR (A-wt) / Damping Factor ≈ 91 dB / 200 Crossovers HPF / FULL / LPF: 30–300 Hz; 12 dB/oct Turn-On Modes REM / DC Operating Voltage 8 – 16 V Current Draw (Music / Max) ≈ 70 A / 130 A Recommended Fuse (Music) ≈ 150 A Dimensions Compact motorcycle-grade chassis Always verify impedance, wiring, and fuse size for your exact setup. Frequently Asked Questions — Motorcycle Audio Can it power fronts and lids cleanly? Yes — run four channels at 2–4Ω for a balanced system, or bridge pairs at 4Ω for more output to lids or mid-bass. Will it work with my factory radio? Yes. Use REM or DC turn-on and set gains carefully. Add a DSP if you need advanced EQ/time alignment. What wiring and fuse do I need? Use OFC power/ground sized for current draw; fuse at the battery (≈150 A music). Keep grounds short and solid. Is it motorcycle-ready? Yes — designed for bikes. Mount away from direct spray and protect cables from abrasion/heat. Garage Bagger Stereo Advantage Bike-specific amp placement & heat management Clean, serviceable OFC wiring and correct fusing On-bike tuning for loud, clear highway performance Nationwide shipping and tech support Need Help? Call us at (864) 334-6131 with your bike and speakers. We’ll map gains, filters, and wiring for your exact setup.Sale