Browse Collections
-
Beyma PRO6CXND - 6.5" Pro Coaxial Speaker (Single)
Vendor:BeymaBeyma PRO6CXND 6.5" Pro Coaxial Speaker (Sold in Singles) Nominal diameter 165 mm 6.5 inNominal impedance LF/HF 8/8 ohmPower capacity LF/HF 200/40 W AESProgram power LF/HF 400 / 80 wSensitivity LF/HF 95/104 2.83 @ 1 m @ 2πFrequency range 82-20000 Hz -
Beyma PRO6FX240ND - 6.5" Pro Carbon Fiber Coaxial Speaker (Single)
Vendor:BeymaBeyma PRO6FX240ND 6.5" Pro Carbon Fiber Coaxial Speaker (Sold in Singles) KEY FEATURES• High power handling: 400 / 80 W Program Power (LF / HF)• High Sensitivity: 94 / 103 dB (LF / HF)• Extended controlled displacement: Xmax 5,5 mm shorting copper pad for low harmonic distortion and linear impedance• Carbon Fiber cone with High-End quality sound CONEX spider for higher resistance and consistency• Common Neodymium magnetic system for low-weight and mounting depth• Excellent off-axis response 70° conical coverage for HF dispersion control• PM4 diaphragm for natural sound Specifications Nominal Basket Diameter 6.5" / 165mm Impedance 8 ohms Low Frequency AES Power Rating 200 Watts Low Frequency Program Power 400 Watts High Frequency AES Power Rating 40 Watts High Frequency Program Power 80 Watts Frequency Response 100Hz - 20kHz High Frequency Sensitivity (1W/1m) 103dB Low Frequency Sensitivity (1W/1m) 94dB LF Voice Coil Diameter 2" / 50.8mm HF Voice Coil Diameter 1.75" / 44.4mm Recom. Crossover Frequency 2.5kHz or higher @ 12dB/oct. Voice Coil Length 14 mm Air Gap Height 7 mm X Damage (peak to peak) 26 mm BL Factor 9.1 N/A Mounting Information Overall Diameter 6.9" / 174mm Bolt Circle Diameter 6.2" / 158mm Baffle Cutout Diameter 5.71" / 145.1mm No. Of Mounting Holes 4 Volume Displaced By Driver 0.02 ft3 / .55 Liters Overall Depth 4.0" / 103.1mm Net Weight 4.2 lb. / 1.9 kg. Shipping Weight 4.6 lb. / 2.1 kg. Materials Low Frequency Woofer Basket Die-Cast Aluminum Cone Carbon Fiber Surround Two Roll Treated Cloth Voice Coil Aluminum Spider Conex Magnet Neodymium High Frequency Tweeter Diaphragm PM-4 Voice Coil Edgewound Aluminum Ribbon Voice Coil Former Kapton Magnet Neodymium Thiele-Small Parameters Resonant Frequency (fs) 100 Hz Impedance (Re) 4.6 ohms Coil Inductance (Le) .24 mH Mechanical Q (Qms) 3.5 Electrical Factor (Qes) .56 Total Q (Qts) .48 Comp. Equivalent Vol. (Vas) .14 ft3 / 4 Liters Voice Coil Overhang (Xmax) 5.5 mm Diaphragm Mass (Mms) 15 Grams Surface Area of Cone (Sd)m2 0.0135m2 Reference Efficiency .83% Displacement Volume (Vd) 74 cm3 -
SaleCicada Audio CH65 6.5" Pro Coaxial Horn Speaker (Pair)
Vendor:Cicada AudioCicada Audio CH65 6.5" Pro Coaxial Horn Speaker Pair Cicada Audio CH65 6.5" Pro Coaxial Horn Speakers are built for Harley-Davidson baggers and high-output motorcycle audio systems that need real volume, strong projection, and cleaner sound at highway speed. The CH65 combines a powerful midbass driver with an integrated horn tweeter for loud vocals, crisp highs, aggressive open-air output, and the kind of efficiency needed for amplified Harley audio builds. Shop Cicada Audio 6.5" Pro Coax Speakers Cicada Amplifiers THE REFERENCE STANDARD High-Output 6.5" Cicada Speakers for Harley Audio Built for riders who want louder fairing speaker output, sharper vocals, stronger mids, and better projection from a 6.5" motorcycle speaker location. Start a Build Consultation Call 864-334-6131 Key Product Details Product Cicada Audio CH65 6.5" Pro Coaxial Horn Speaker Pair Current Part Numbers CH652C = 2Ω version / CH654C = 4Ω version Speaker Size 6.5" Speaker Type Pro coaxial horn speaker Sold As Pair Best For Harley-Davidson bagger audio, fairing speaker upgrades, high-output motorcycle audio systems, and amplified 6.5" speaker locations System Goal Louder vocals, stronger mids, crisp highs, better projection, and cleaner highway-speed output Always verify impedance, amplifier power, speaker pod fitment, mounting depth, wiring, and tuning before ordering for your Harley-Davidson audio build. Built for Loud Harley-Davidson Bagger Audio The Cicada CH65 is a strong choice for riders upgrading factory Harley-Davidson audio systems with aftermarket amplifier power. These speakers are made for motorcycle audio builds where basic replacement speakers are not enough and the goal is more volume, stronger clarity, and real projection while the bike is moving. If you are building a louder fairing speaker setup, a pro-audio style motorcycle system, or a high-output Harley bagger audio upgrade, the CH65 gives you the efficiency and output needed to cut through wind noise, road noise, and helmet interference. Fitment Note On 2015+ Road Glide models, speaker pods may require modification for proper installation. Always verify pod clearance, mounting depth, speaker location, impedance, amplifier compatibility, and final system layout before ordering. Specifications Power Handling 500 watts RMS / 1000 watts max per pair Frequency Response 75Hz–20kHz +/-5dB Magnet Structure Neodymium high-energy lightweight N35 magnet Basket Heavy-duty die-cast aluminum basket Midbass Voice Coil 2.0" high-temp voice coil Tweeter Voice Coil 1.4" aluminum diaphragm high-temp voice coil Sensitivity 94dB / 99dB average 1W/1M, 2.83V Crossover 12dB crossover with custom-tooled vented crossover case Bi-Amp Capable Horn tweeters can be run on dedicated amplifier channels Heat Control Advanced voice coil heat sink design for improved heat dissipation Speaker Control Shorting ring design for improved speaker control Mounting Depth 3.0" / 76.2mm Mounting Diameter 5.7" / 145.5mm Treatment Weather treated for motorcycle audio use Sold Pair Best Use for the Cicada CH65 The Cicada CH65 is best used in Harley-Davidson motorcycle audio builds where the goal is louder fairing speaker output, stronger vocal projection, improved clarity, and more efficient performance from a 6.5" speaker location. Amplified System Recommended These are not basic replacement speakers. The CH65 is intended for amplified motorcycle audio systems where output, control, tuning, and projection matter. Related Cicada & Motorcycle Audio Paths Build the system around the correct speaker, amplifier, DSP, wiring, and installation path. These related collections help match the CH65 with the right Harley audio upgrade direction. Shop Motorcycle 6.5" Pro Coaxial Speakers Shop Cicada Audio motorcycle speakers, amplifiers, DSP, and bagger audio upgrades Shop Cicada motorcycle amplifiers for Harley-Davidson audio builds Shop motorcycle DSP for Harley-Davidson audio tuningSale -
SaleCicada Audio CHX525 5.25" Pro Coaxial Speaker (Pair)
Vendor:Cicada AudioCHX525.2 or .4Ω HIGH-PERFORMANCE PRO COAX HORN SPEAKERS New to our pro-line horn series, the CHX525.2 5.25″ coax horn speaker features a 1.5″, 2Ω, voice coil woofer and a 1.0″ horn, 8Ω, tweeter. It handles big power and is high-performance. 150w RMS / 300w MAX Power Handling each Heavy duty diecast basket 1.5″ high temp voice coil for mid-bass 1.0″ high temp voice coil for tweeter Freq Response: 90Hz – 20kHz +/- 5dB 91dB Sensitivity External 12dB / 6kHz tweeter crossover Mounting Depth: 2.26″ / 70mm Mounting Diameter: 5.25″ / 133mmSale -
SaleCicada Audio CHX65 6.5" Pro Coaxial Speaker (Pair)
Vendor:Cicada AudioCicada Audio CHX65 6.5" Pro Coax Horn Speakers Cicada Audio CHX65 6.5" Pro Coax Horn Speakers are built for Harley-Davidson bagger audio systems that need loud, clean, all-weather motorcycle sound at highway speed. Designed for high-output motorcycle audio, the CHX65 combines a 6.5" pro coaxial driver, horn-loaded clarity, Carbon Matrix Composite cone construction, and strong projection for riders who want more output from their Harley audio system. Shop Cicada Audio 6.5" Pro Coax Speakers Cicada Amplifiers THE REFERENCE STANDARD All-Weather 6.5" Cicada Speakers for Harley Audio Built for riders who want loud vocals, sharper clarity, stronger projection, and real motorcycle audio performance from a 6.5" Harley speaker location. Start a Build Consultation Call 864-334-6131 Key Product Details Product Cicada Audio CHX65 6.5" Pro Coax Horn Speakers Current Part Numbers CHX65.2 = 2Ω version / CHX65.4 = 4Ω version Speaker Size 6.5" Speaker Type Pro coaxial horn speaker Best For Harley-Davidson bagger audio, fairing speaker upgrades, high-output motorcycle audio systems, and amplified 6.5" speaker locations System Goal Louder vocals, stronger projection, clean open-air output, all-weather durability, and better highway-speed performance Sold As Pair Always verify impedance, speaker location, mounting depth, amplifier power, wiring, crossover setup, and final fitment before ordering for your Harley-Davidson audio build. Built for Harley-Davidson Bagger Audio The Cicada CHX65 is made for riders who want more than a basic replacement speaker. It is built for Harley-Davidson Touring, Road Glide, Street Glide, CVO, and custom bagger audio systems that need louder output, cleaner vocals, better clarity, and strong projection in real riding conditions. With a horn-loaded design, all-weather protection, high-efficiency output, and motorcycle-focused construction, the CHX65 is a strong fit for amplified Harley audio systems where the speaker needs to perform at speed, not just sound good in the garage. All-Weather Pro Coax Horn Design The CHX65 uses Cicada’s all-weather design with a Nanofram horn cover, Carbon Matrix Composite cone, neodymium magnet structure, aluminum tweeter diaphragm, and external crossover network. This makes it a strong speaker choice for Harley riders who want loud, clear, reliable motorcycle audio in real-world riding conditions. The included horn cover helps protect the compression driver, while the pro coaxial layout gives the speaker the projection and efficiency needed for open-air Harley audio builds. Specifications Speaker Size 6.5" pro coaxial horn driver Impedance Options CHX65.2 = 2Ω / CHX65.4 = 4Ω Power Handling 300 watts RMS / 600 watts max Frequency Response 70Hz–20kHz +/-4dB Sensitivity 92dB, 1W / 1M Midbass Voice Coil 2.0" / 51mm high-temperature voice coil Tweeter Voice Coil 1.4" / 35.56mm tweeter voice coil Cone Carbon Matrix Composite™ cone Tweeter Dome Aluminum tweeter diaphragm Magnet Neodymium magnet structure Crossover External 12dB custom-tooled, vented, encased crossover Tweeter Attenuation -3dB / -6dB heat-sink encased resistor pack Horn Cover Nanofram™ horn cover Weather Protection Exclusive Cicada all-weather design for rain protection, waterproofing, and UV protection Mounting Depth 2.64" / 67mm Mounting Diameter 5.67" / 144mm Best Use for the Cicada CHX65 The CHX65 is best used in Harley-Davidson bagger audio systems where the goal is loud 6.5" speaker output, strong vocal projection, clean highs, and better performance from fairing or custom speaker locations. Amplified System Recommended These speakers are intended for serious motorcycle audio systems. For best results, match the CHX65 with proper amplifier power, correct impedance selection, clean wiring, and a real tuning plan. Fitment and Installation Notes The Cicada CHX65 is designed for 2014+ Harley-Davidson factory-designed speaker locations, but every motorcycle audio build should be verified before ordering. Confirm speaker depth, mounting diameter, pod clearance, grille clearance, wiring path, impedance, and amplifier compatibility before installation. Some Harley-Davidson Road Glide, Street Glide, CVO, and custom bagger applications may require installation planning, speaker pod work, adapter rings, or system tuning depending on the exact bike and audio layout. Related Cicada & Motorcycle Audio Paths Build the system around the correct speaker, amplifier, DSP, wiring, and installation parts. These related collections help match the Cicada CHX65 with the right Harley audio upgrade path. Shop Motorcycle 6.5" Pro Coaxial Speakers Shop Cicada Audio motorcycle speakers, amplifiers, DSP, and bagger audio upgrades Shop Cicada motorcycle amplifiers for Harley-Davidson audio builds Shop motorcycle DSP for Harley-Davidson audio tuning Shop motorcycle speaker installation parts Need Help Choosing the Right Cicada Speakers? Need help matching the Cicada CHX65 to your Harley-Davidson bagger audio build? Call Garage Bagger Stereo or start a build consultation and we’ll help match the speaker, impedance, amplifier power, DSP, wiring, and installation path to your bike and sound goal. Call 864-334-6131 Start a Build ConsultationSale -
SaleCicada Audio CXX525 5.25" Pro Coaxial Speakers | 2Ω or 4Ω – Pair
Vendor:Cicada Audio5.25-INCH MOTORCYCLE PRO COAXIAL AUDIO Cicada Audio CXX525 5.25" Pro Coaxial Speakers | 2Ω or 4Ω – Pair The Cicada Audio CXX525 is a high-performance 5.25-inch Pro Coaxial speaker pair available in 2Ω and 4Ω versions. Each speaker combines a lightweight Kevlar cone, integrated PEI tweeter, V8™ Dispersion Guide and compact neodymium motor for clear, efficient motorcycle audio performance in demanding open-air riding conditions. Choose Impedance View Specifications Compact Pro Coaxial Performance Available in 2Ω and 4Ω configurations Sold as a matched pair 100 watts RMS per speaker 200 watts maximum per speaker Kevlar mid-bass cones Integrated PEI dome tweeters Built-in 6dB crossover V8™ Dispersion Guide for wide tweeter output Rain or Shine™ all-weather construction Protective grilles and hardware included Cicada CXX525 Pro Coaxial Overview The Cicada Audio CXX525 is designed for motorcycle audio systems that need full-range sound from a compact 5.25-inch speaker platform. Its coaxial design combines the mid-bass driver and tweeter into one speaker assembly. This reduces the number of separate components required while providing strong mid-bass, clear vocals and high-frequency detail from compatible factory or custom motorcycle speaker locations. Select the CXX525.2 2Ω version or the CXX525.4 4Ω version based on your amplifier, channel configuration and final speaker impedance. Available Impedance Options and SKUs CXX525.2 — 2-Ohm Version Select the 2Ω version when your amplifier is stable at the intended 2-ohm channel load and your complete speaker wiring is designed for the lower impedance. CXX525.4 — 4-Ohm Version Select the 4Ω version for amplifiers and multi-speaker systems designed around a 4-ohm channel load. Choose the correct impedance: The proper version depends on your amplifier’s rated load, the number of speakers connected to each channel and the complete series or parallel wiring configuration. What Comes in the Box Two Cicada Audio CXX525 5.25-inch Pro Coaxial speakers Selected 2Ω or 4Ω speaker configuration Two protective 5.25-inch speaker grilles Speaker installation hardware Important: Motorcycle-specific speaker adapters, fairing brackets, wiring harnesses, amplifier wiring and signal integration components are not included unless specifically added as product options. Why Riders Choose the CXX525 100W RMS Power Handling Each 5.25-inch speaker handles 100 watts RMS and 200 watts maximum for strong output from a properly matched motorcycle amplifier. 2Ω or 4Ω Variants Two impedance options allow the speakers to be matched to different amplifiers, channel loads and multi-speaker configurations. Pro Coaxial Design The integrated mid-bass driver and tweeter provide full-range output without requiring a separately mounted tweeter. V8™ Dispersion Guide Cicada’s dispersion guide is designed to distribute tweeter output more evenly around the speaker for broader high-frequency coverage. Kevlar Cone The lightweight Kevlar cone is strong, heat resistant and moisture resistant for efficient, controlled mid-bass performance. All-Weather Construction Rain or Shine™ construction and UV-protected surfaces are designed for exposed motorcycle audio environments. CXX525 Speaker Technology V8™ Dispersion Guide supports wide high-frequency dispersion from the integrated tweeter Built-in 6dB crossover manages the transition between the mid-bass driver and integrated tweeter Kevlar cone provides a lightweight, rigid and moisture-resistant speaker diaphragm PEI tweeter dome delivers bright, efficient high-frequency output Copper voice coils support efficient conductivity while helping control heat N45H neodymium motor provides strong output without the weight of a conventional ferrite motor Custom-tooled polycarbonate basket is designed for high-temperature motorcycle installations UV-protected surfaces help resist fading and damage from extended exposure to sunlight Cicada CXX525 Specifications Available Models CXX525.2 and CXX525.4 Speaker Type 5.25-inch high-performance Pro Coaxial speaker Quantity Pair Impedance Options 2Ω or 4Ω 2Ω Variant SKU CXX525.2 4Ω Variant SKU CXX525.4 Power Handling 100W RMS / 200W maximum per speaker Mid-Bass Voice Coil 1.4 inches / 35mm Tweeter Voice Coil 1 inch / 25mm Cone Material Kevlar Tweeter Dome PEI Built-In Crossover 6dB Magnet N45H neodymium Sensitivity 91dB, 1W / 1M Frequency Response 50Hz–20kHz ±3dB Mounting Depth Approximately 2.25 inches / 57mm Mounting Diameter 4.6 inches / 116mm Grilles Included Warranty Two-year manufacturer warranty Motorcycle Fitment Cicada Audio designs the CXX525 for compatible factory-style speaker locations used in Harley-Davidson, Indian and Honda motorcycle audio applications. Verify fitment: Confirm the motorcycle year, model, factory audio package, speaker opening, mounting depth, grille clearance, connector type and required mounting adapters before ordering. Compatible with properly sized 5.25-inch motorcycle speaker locations. Model-specific mounting brackets or adapters may be required. Factory speaker connectors may require an adapter or new terminals. Confirm the 4.6-inch mounting opening before installation. Confirm approximately 2.25 inches of available mounting depth. Verify that the included grille fits the intended installation location. Amplifier and Crossover Setup Protect the speakers: The built-in crossover divides frequencies between the mid-bass driver and tweeter, but the amplifier still requires an appropriate high-pass filter and properly set gain. Select CXX525.2 for a compatible 2Ω amplifier channel load. Select CXX525.4 for a compatible 4Ω amplifier channel load. Do not connect a 2Ω speaker to an amplifier channel not rated for 2Ω operation. Confirm final impedance when multiple speakers share one amplifier channel. Use an appropriate high-pass crossover for the speaker location and system goals. Set amplifier gain using clean measured output rather than control position alone. Reduce low-frequency output that exceeds the speaker’s operating range. Professional system tuning is recommended. Best For Compatible Harley-Davidson factory-style 5.25-inch locations Compatible Indian motorcycle speaker locations Compatible Honda motorcycle speaker locations Motorcycle fairing and rear-pod speaker upgrades Amplified systems requiring a 2Ω speaker option Amplified systems requiring a 4Ω speaker option Riders wanting full-range sound from a compact coaxial platform Custom motorcycle and powersports audio installations Related Motorcycle Audio Categories Cicada and Motorcycle Speakers Shop Cicada Audio Shop Motorcycle Speakers 2023.5+ / 2024+ Harley Plug-and-Play Kits Amplifiers and Signal Motorcycle Amplifiers Motorcycle Amplifier Installation Parts Motorcycle DSP and Signal Integration Installation Support Motorcycle Batteries Motorcycle Audio Installation in Taylors, SC Request a Custom Audio Build Cicada CXX525 FAQ Is this listing for the 2Ω or 4Ω version? This single listing includes both versions. Select CXX525.2 for the 2Ω speaker pair or CXX525.4 for the 4Ω speaker pair before adding the product to your cart. Are the CXX525 speakers sold individually or as a pair? Both the CXX525.2 and CXX525.4 variants are sold as a pair. Which impedance should I choose? Choose the impedance supported by your amplifier and complete speaker wiring plan. The final channel load depends on the number of speakers connected and whether they are wired individually, in series or in parallel. How much power can the CXX525 handle? Each speaker is rated for 100 watts RMS and 200 watts maximum power. Are these coaxial speakers? Yes. Each CXX525 combines a 5.25-inch mid-bass driver and integrated tweeter in one Pro Coaxial speaker assembly. Does the CXX525 use an external crossover? No external component crossover is required for the integrated tweeter. The speaker includes a built-in 6dB crossover. Are speaker grilles included? Yes. The speaker pair includes protective grilles and installation hardware. Will these fit every 5.25-inch motorcycle speaker location? No. Fitment depends on the motorcycle year, model, speaker opening, mounting depth, grille clearance and required mounting adapters. Does this speaker pair need an amplifier? A properly matched motorcycle amplifier that is stable at the selected speaker impedance is recommended to take advantage of the speakers’ output and power handling. What warranty does Cicada Audio provide? Cicada Audio lists a two-year manufacturer warranty for both CXX525 impedance variants. Need Help Choosing 2 Ohms or 4 Ohms? Call Garage Bagger Stereo with your motorcycle year, model, speaker locations, amplifier and planned wiring. We’ll help determine which CXX525 impedance is correct and identify the proper mounting, wiring and signal-integration components for your system. Call 864-334-6131 Ask GBS for HelpSale -
SaleDB Drive Euphoria XPERT EX6NCD-CFV2 6.5″ 2-Way Loudspeakers
Vendor:DB DriveDB Drive XPERT 6.5" 2-Way NEO Carbon Fiber Loudspeakers EX6NCD-CFV2 (Pair) Built for serious high-output sound systems, the DB Drive Xpert EX6NCD-CFV2 combines competition-level performance with exceptional clarity and durability. The included 12dB passive crossover ensures clean frequency separation, while the custom aluminum basket with radial venting improves cooling and long-term reliability. Features 2.0" (51mm) Voice Coil Neodymium M-Ring Magnet Assembly Optimized for High Output SQ Sound Systems Rear-Mounted Full-Sized Compression Driver Weather-Resistant Carbon Fiber Cone with Cloth Surround Custom Aluminum Basket with Radial Venting 1.4"(36mm) Polyester Tweeter Diaphragm Wide Dispersion Conical HF Waveguide 12dB Passive Crossover Included Protective Grills Included Specifications Impedance: 3Ω Power Handling: 400W Dynamic Wattage: 800W Resonant Frequency: (fs) 92.1 Hz Sensitivity (1w/1M): 106.1 dB Voice Coil: 2.0" Overall Diameter: 6.52" Cutout Diameter: 5.49" Mounting Depth: 2.72" Dimensions Overall Diameter: 6.85"/ 174 mm Cutout Diameter: 5.49"/ 139.43 mm Mounting Depth: 3.44"/ 87.30 mmSale -
DB Drive WDX6MOTO-CD (pairs)
Vendor:DB DriveTRUE SOUND. TRUE SOURCE. Specifications Max Power 500 watts Nominal Power 250 watts Freq Response 90-18000 Impedance 4Ω Sensitivity 102.7db 6.5″ High Efficiency 2-way Loudspeaker 1″ Aluminum Compression Style Tweeter Element Rated Cone Design Bi-Ribbed Treated Cloth Surround 1.5″ High Output Til Midrange Voice Protective Grill Included Dimensions Depth 3.08" Cutout Diameter 5.67" -
SaleDiamond Audio Motorsports 2-WAY 6.5" Flush Mount Speaker (2Ω and 4Ω)
Vendor:Diamond AudioAll Weather 6.5 Coaxial Driver Speaker Flush Mount 2Ω or 4Ω Speaker Diamond Audio proudly expands its Motorsport HXM speaker line with a series of new flush-mount versions and higher-performance, higher-power handling Elite series models. The speakers are designed with precise measurements to perfectly fit most Harley-Davidson motorcycles and maintain that custom factory appearance. Speaker grills are optional. SPECIFICATIONS: 4Ω or 2Ω– 6.5-inch coaxial driver Freq response range 80hz-18Khz +/- 4dB Sensitivity: 92dB, 1W / 1M Power handling: 125W RMS/250W MAX Mounting Depth 2.56" Mounting Diameter 5.63" Water Spray and Salt Water Resistant, 100% UV Stable Ultra Small Neodymium Motor Structure With Max Xmax Suspension Molded, UV-coated, Patent Pending Waterproof Injection PP Cone Integrated Dream RGB LED LightingSale -
SaleDiamond Audio MP525 5.25" Pro Full-range Coax Horn Speaker (Pair)
Vendor:Diamond AudioDiamond Audio MP525 2-Way Loudspeaker With Backloaded Compression Driver Features 1.5" Voice Coil Neodymium Ring Magnet Assembly Rear Mounted Full Sized Compression Driver 150W RMS /300Max power 12DB Crossover for Compression Drivers Freq Response 110Hz-18kHz 101 Db/1W Power Sold in PairsSale -
SaleDiamond Audio MP65 (2Ω and 4Ω) 6.5" Pro Coaxial Speaker
Vendor:Diamond AudioMP654 – 6.5” PRO Full-Range Coax Horn Speaker Features 1.5" Voice Coil Available in 2Ω or 4Ω Freq Response 110Hz-18kHz 101 Db/1W Power Neodymium Ring Magnet Assembly Rear Mounted Sized Compression Driver 150W RMS /300Max power 12DB Crossover for Compression Drivers 101 Db/1W Power Mounting Depth: 3.33” / 84.6mm Mounting Diameter: 5.73” / 145.5mm Pods will need to be modified on 14 and up HD Not a direct fit for tour pak Not a drop-in speaker for lowers may need a spacer and or modification Add them to your Lowers or Pak with this kit Sold in Pairs Weather treatedSale -
SaleDiamond Audio MS652NEO 6.5" 2-Way Coaxial Neo Speakers (2Ω or 4Ω)
Vendor:Diamond AudioDiamond Audio MS652NEO 6.5" Pro Coaxial Neo Speakers — 2Ω or 4Ω The Diamond Audio MS652NEO is a 6.5-inch horn-loaded pro coaxial speaker designed for serious motorcycle, marine, powersports, and high-output vehicle audio systems. Its combination of a carbon-fiber cone, PEN high-frequency diaphragm, neodymium motor structure, and cast-aluminum basket is engineered to produce strong projection and clean output in demanding open-air environments. Available in 2-ohm and 4-ohm versions, the MS652NEO delivers 200 watts RMS of power handling with a dual-voice-coil, bi-ampable architecture that gives system builders additional flexibility when configuring amplification and DSP control. THE REFERENCE STANDARD 6.5" Pro Coaxial Output Built for the Highway Horn-loaded high-frequency projection, carbon-fiber midrange performance, and efficient neodymium motor technology for serious motorcycle audio systems. Start a Build Consultation Call 864-334-6131 Diamond Audio MS652NEO Key Specifications Series MS NEO Speaker Size 6.5 inches Speaker Type 2-Way Horn-Loaded Pro Coaxial 2Ω Model MS652NEO2 4Ω Model MS652NEO4 Power Handling 200W RMS / 400W MAX Sensitivity 93 dB (1W/1M) Voice Coil Configuration Dual Voice Coil Bi-Ampable Yes Field-Serviceable Voice Coil Yes Voice Coil Diameter 2 inches Cone Material Carbon Fiber High-Frequency Diaphragm PEN — Polyethylene Naphthalate Motor Neodymium Basket Cast Aluminum Surround Rubber Re 3.2Ω Qms 10.357 Qes 0.67 Qts 0.629 Fs 151 Hz Vas 2.756 L Cms 0.094 mm/N Mms 11.728 g Sd 143.14 cm² BL 7.289 T·m Xmax 1.2 mm Mounting Depth 3.43″ (87.13 mm) Cutout Diameter 5.63″ (143 mm) Overall Diameter 6.65″ (169 mm) Overall Height 3.79″ (96.33 mm) Fitment warning: These are high-output 6.5-inch pro coaxial speakers and are not a universal drop-in replacement. Verify cutout diameter, mounting depth, motor clearance, grille clearance, amplifier power, impedance, and complete system layout before ordering. 200W RMS High-Output Pro Coaxial Performance The MS652NEO is designed for motorcycle audio systems where a traditional automotive coaxial speaker may not provide enough output or projection. Its horn-loaded architecture increases high-frequency efficiency while the carbon-fiber cone handles the midrange and midbass frequencies required for strong open-air performance. Diamond Audio's formal technical specifications rate the MS652NEO platform at 200 watts RMS and 400 watts maximum power. Horn-Loaded Coaxial Architecture The high-frequency driver is positioned within the same overall speaker platform as the 6.5-inch cone, creating a compact coaxial system capable of delivering both midrange and high-frequency output from one mounting location. The horn-loaded high-frequency section is designed to improve projection so vocals, cymbals, guitars, and other upper-frequency information remain audible against wind, road, engine, and exhaust noise. Carbon-Fiber Cone and Neodymium Motor Diamond Audio uses a rigid carbon-fiber cone to provide a strong, lightweight moving surface capable of maintaining control at elevated playback levels. The neodymium motor provides high magnetic strength while reducing the size and weight associated with conventional ferrite magnet structures, making the platform particularly useful for motorcycle and powersports installations. PEN High-Frequency Diaphragm High-frequency reproduction is handled by a PEN — polyethylene naphthalate — diaphragm. Combined with the horn-loaded architecture, this design is intended to provide clean, efficient high-frequency output with strong forward projection. Choose 2Ω or 4Ω The MS652NEO is available in separate 2-ohm and 4-ohm configurations. The correct version should be selected based on amplifier output, number of speakers, channel configuration, wiring method, and final impedance presented to the amplifier. 2Ω — MS652NEO2 The 2-ohm version is suited to systems where the amplifier and channel configuration are designed to operate at a lower impedance and provide increased available power. 4Ω — MS652NEO4 The 4-ohm version provides greater flexibility for multi-speaker wiring and amplifier configurations where a higher final impedance is required. Dual Voice Coil and Bi-Amp Capability The MS652NEO uses a dual-voice-coil, bi-ampable architecture. This allows advanced system builders to configure the speaker differently depending on amplifier channel availability and DSP strategy. A properly designed bi-amped system can provide independent amplification and signal processing for different sections of the coaxial platform, allowing greater control over crossover points, output level, EQ, and time alignment. System-design note: Bi-amp capability does not mean the speaker must be bi-amped. Wiring, amplifier channels, crossover configuration, and DSP settings must be planned around the complete system and the selected 2Ω or 4Ω version. Cast-Aluminum Basket and Field-Serviceable Design The rigid cast-aluminum basket provides structural support and helps resist flex and vibration during high-output operation. Diamond Audio also specifies a field-serviceable voice-coil design, adding serviceability for demanding custom motorcycle, marine, and powersports systems. Built for Motorcycle and Powersports Audio With its compact 6.5-inch format, high-output architecture, and 3.43-inch mounting depth, the MS652NEO is suited to a wide range of custom motorcycle and powersports speaker locations where adequate physical clearance is available. Harley-Davidson custom audio systems. Road Glide and Street Glide fairing applications. Custom lower speaker pods. Saddlebag speaker installations. Tour-pack speaker locations. Custom fabricated speaker panels. Marine and powersports applications. Slingshot and UTV audio systems. Installation and Tuning Notes Select the 2Ω or 4Ω model based on amplifier loading and complete system design. Verify amplifier RMS output at the selected impedance. Confirm the 5.63-inch mounting cutout before modifying any factory or aftermarket panel. Verify the complete 3.43-inch mounting depth and rear motor clearance. Confirm the 6.65-inch overall diameter and grille clearance before final assembly. Determine whether the speaker will be conventionally powered or bi-amped before wiring. Use appropriate crossover protection based on amplifier power, installation location, and system goals. Secure all speaker mounting hardware for motorcycle vibration. Protect wiring and terminals from moisture, abrasion, heat, and moving components. Complete final DSP, EQ, crossover, and level tuning after the full system is installed. Diamond Audio MS NEO Coaxial Specifications Review the Diamond Audio MS NEO coaxial technical information before installation and system configuration. View MS NEO Coaxial Specifications Need Help Choosing 2Ω or 4Ω? The correct impedance depends on amplifier output, number of speakers, channel configuration, wiring method, DSP strategy, and the complete system design. Garage Bagger Stereo can help determine the correct MS652NEO version for your system. Start a Build Consultation Call 864-334-6131Sale
Key Specifications
| Speaker Size | 6.5″ |
| Speaker Type | Pro Coaxial (high-sensitivity mid + tweeter) |
| Primary Use | Amplifier-driven fairing and auxiliary locations |
| Performance Focus | Higher output and projection vs standard coaxials |
| System Pairing | Aftermarket amplification with DSP tuning |
| Install Requirement | Correct power, filtering, and mounting depth |
Specifications summarized from manufacturer technical data. Always verify impedance, power handling, and crossover requirements before installation.
6.5″ Pro Coaxial Speaker Overview
High-Output 6.5″ Pro Coaxial Motorcycle Speakers
6.5-inch pro coaxial motorcycle speakers are designed for riders who require higher output and increased efficiency compared to standard coaxial speakers. This collection includes purpose-built pro coaxial models engineered specifically for Harley Davidson and Indian touring motorcycles where amplified performance is the priority.
Pro coaxial speakers use higher-sensitivity midrange drivers and more robust motor structures to achieve greater volume with less power loss. This makes them ideal for systems running aftermarket amplification where clarity and projection must be maintained at sustained highway speeds.
These speakers are commonly installed in fairings, lowers, and select rear locations depending on system design. Compared to entry-level coaxials, pro coaxial speakers deliver stronger midrange presence and improved intelligibility when paired with proper amplification and signal control.
This collection supports audio builds that require:
• Amplifier-driven speaker systems
• Increased output without moving to full pro midrange setups
• Clean, controlled sound at elevated volume levels
• Predictable fitment in common 6.5-inch motorcycle locations
Proper system design is critical when using pro coaxial speakers. Dedicated amplification and DSP tuning are recommended to manage crossover points, protect the speakers, and balance output with the rest of the system.
This page serves as the performance-focused 6.5-inch speaker category for riders building louder, more capable touring audio systems.