No products found
Use fewer filters or remove all
-
Cicada Audio 24FLXPCH-4X2RG 700W DSP 2-Speaker System for 2024+ Road Glide
Vendor:Cicada AudioCOMPLETE 2024+ ROAD GLIDE FRONT AUDIO SYSTEM Cicada Audio 24FLXPCH-4X2RG 700W DSP 2-Speaker System The Cicada Audio 24FLXPCH-4X2RG is a complete front-fairing audio package for compatible 2024 and newer Harley-Davidson Road Glide motorcycles. It combines a four-channel amplifier with built-in DSP, two high-efficiency 2-ohm Coaxial Horn speakers, factory A2B radio integration, Road Glide-specific mounting components and a rear-output harness for future system expansion. See Everything Included View Speaker Load Front Audio with Rear Expansion Support Designed for compatible 2024+ Road Glide motorcycles FLX700.4PRO amplifier with built-in six-channel DSP 175 watts RMS × 4 channels at 2Ω Two CH65.2C 6.5-inch Coaxial Horn speakers Both included speakers are 2Ω Road Glide fairing grilles included NAV-TV ZEN-H A2B factory-radio integration Road Glide amplifier rack included 6-AWG amplifier power kit included Rear-output harness included for future expansion 24FLXPCH-4X2RG Complete System Overview This Cicada Audio package upgrades the two factory Road Glide fairing speaker locations while establishing the amplifier, DSP, power wiring and A2B signal-integration foundation needed for a future four-channel audio system. One pair of CH65.2C 6.5-inch Coaxial Horn speakers installs behind the included Cicada-branded Road Glide fairing grilles. Each speaker has a nominal impedance of 2 ohms and connects to its own amplifier channel. The included FLX700.4PRO provides four amplified DSP channels. The supplied package uses two channels for the front speakers, while the included 24HDRO harness prepares the system for a separately purchased rear-speaker upgrade. Speaker Impedance and Amplifier Channel Load Front Left: 2Ω One CH65.2C speaker connects to the assigned left-front amplifier channel and presents a nominal 2-ohm load. Front Right: 2Ω The second CH65.2C speaker connects to the assigned right-front amplifier channel and presents a nominal 2-ohm load. Rear Channels: Available No rear speakers are supplied. The remaining two amplified channels can support a properly matched future rear-speaker system. Included Speaker Count Two speakers / one pair Included Speaker Model CH65.2C Speaker Impedance 2Ω per speaker Supplied Configuration One 2Ω speaker on each of two amplifier channels Remaining Amplified Channels Two channels available for compatible rear-speaker expansion Supplied system load: Only two amplifier channels are loaded by the included speakers. Each loaded channel operates at a nominal 2 ohms. Any future rear speakers must be matched to the amplifier’s supported impedance and available output. Everything Included in the Complete System FLX700.4PRO — Four-Channel DSP Amplifier One compact Class-D amplifier producing up to 175 watts RMS × 4 channels at 2 ohms. It includes a six-channel DSP with four internally amplified channels and two processed pass-through outputs. CH65.2C — 6.5" Coaxial Horn Speakers One pair of 2-ohm Larry Frederick Classic Coaxial Horn speakers for the Road Glide fairing. Each speaker is rated for 250 watts RMS and includes an external 12dB crossover. 24CHDRGG — Road Glide Fairing Grilles One pair of Cicada Audio-branded, powder-coated steel fairing grilles engineered for compatible 2024 and newer Road Glide motorcycles. 24HDAR-RG — Road Glide Amplifier Rack Black-anodized aluminum amplifier mounting rack that uses compatible OEM amplifier mounting locations and includes predrilled FLX mounting points and installation hardware. HDPG6K — 6-AWG Amplifier Power Kit Includes six-foot power and ground cables with braided covering, battery-side ring terminals, amplifier-side ferrules, remote trigger wiring, a waterproof Mini-ANL fuse holder and multiple fuse values. 24HDZENHCAKIT — NAV-TV ZEN-H A2B Interface NAV-TV ZEN-H factory A2B interface with a Cicada Audio direct-connect amplifier harness and correctly pinned locking Molex connections. 24HDRO — Rear Output Speaker Harness Plug-and-play rear-output harness with factory-style connectors, two short extensions and two longer speaker-wire leads for future rear-speaker installation. Rear-speaker ready: The rear-output harness is included, but rear speakers, saddlebag speaker adapters, speaker lids and cut-in mounting components are not included with 24FLXPCH-4X2RG. FLX700.4PRO Amplifier and DSP 175W × 4 at 2Ω The amplifier produces up to 175 watts RMS on each of four channels when operating at 2 ohms and 14.4 volts. 120W × 4 at 4Ω It also supports four-channel operation with compatible 4-ohm speakers for systems designed around that channel load. 350W × 2 Bridged The published bridged configuration is 350 watts RMS × 2 into compatible 4-ohm loads. Six-Channel DSP Four DSP channels feed the internal amplifier, while two additional processed channels provide pass-through outputs for expansion. Bluetooth and USB-C Bluetooth audio streaming and USB-C computer connectivity support compatible playback and PC-based DSP configuration. Compact Motorcycle Chassis The micro-sized aluminum chassis is designed for limited fairing space and uses conformal-coated circuitry for added protection against moisture and vibration. FLX700.4PRO Amplifier Specifications Amplifier Model FLX700.4PRO Amplifier Type Four-channel Class-D amplifier with built-in DSP Output at 4Ω 120W RMS × 4 channels at 14.4V Output at 2Ω 175W RMS × 4 channels at 14.4V Bridged Output at 4Ω 350W RMS × 2 channels at 14.4V DSP Channels Six total: four amplified and two pass-through Bluetooth Audio Included PC DSP Connection USB-C Operating Voltage 9V–16V Music Current Draw 50A Maximum Current Draw 80A Recommended Fuse 50A Efficiency 80% Frequency Response 20Hz–20kHz ±3dB Signal-to-Noise Ratio 91dB A-weighted Damping Factor 200 Input Sensitivity 0.2V–12V Turn-On Modes REM / DC / VOX Dimensions with Brackets 5.3 × 4.9 × 2.0 inches / 134 × 125 × 51mm Chassis Dimensions 4.1 × 4.9 × 2.0 inches / 104 × 125 × 51mm CH65.2C Road Glide Fairing Speakers Speaker Model CH65.2C Quantity Two speakers / one pair Speaker Type 6.5-inch Larry Frederick Classic Coaxial Horn Nominal Impedance 2Ω per speaker Power Handling 250W RMS / 500W maximum per speaker Mid-Bass Voice Coil 2 inches / 51mm Tweeter Voice Coil 1.4 inches / 36mm Tweeter Dome Aluminum Cone Water-resistant treated paper Magnet N35SH neodymium External Crossover 12dB at 4kHz Sensitivity 96.4dB, 1W / 1M Frequency Response 75Hz–20kHz ±5dB Mounting Depth 3.0 inches / 76.2mm Mounting Diameter 5.7 inches / 145.5mm Warranty Two-year manufacturer warranty Road Glide-Specific Hardware 24CHDRGG Fairing Grilles The included powder-coated steel grilles are shaped for compatible 2024 and newer Road Glide fairings and feature Cicada Audio-branded emblems. 24HDAR-RG Amplifier Rack The black-anodized aluminum rack mounts at compatible factory amplifier locations and includes predrilled holes for Cicada FLX-style amplifiers. Rear-Speaker-Ready System Design The FLX700.4PRO is a four-channel amplifier, but this package includes only the two front fairing speakers. Cicada includes the 24HDRO harness so compatible rear speakers can be added later without replacing the original amplifier or rebuilding the complete signal path. Included for Expansion Two additional amplified channels 24HDRO rear-output harness Factory-style harness connections Long speaker-wire leads for rear routing Not Included Rear saddlebag speakers Saddlebag speaker adapters Cut-in speaker-lid hardware Rear speaker grilles or pods Expansion planning: Added rear speakers must be compatible with the amplifier’s supported impedance, available power, DSP channel configuration and overall motorcycle electrical system. Factory A2B Radio Integration The NAV-TV ZEN-H interface extracts the factory digital A2B audio signal. The included Cicada harness then routes that signal directly into the FLX700.4PRO through correctly pinned Molex connections. Designed for compatible 2024+ Harley-Davidson A2B systems No cutting or splicing of the factory signal harness Positive-locking automotive-grade connectors Direct connection to compatible Cicada Audio amplifiers Compact routing inside the Road Glide fairing DSP processing handled by the FLX700.4PRO amplifier System distinction: The included ZEN-H is the non-DSP interface configuration. Digital signal processing, equalization, crossovers and channel control are performed inside the FLX700.4PRO. Installation and System Setup Mount the amplifier securely on the included 24HDAR-RG rack. Use the included HDPG6K power and ground wiring kit. Install the correctly rated fuse near the battery connection. Use the included A2B interface and Cicada amplifier harness. Install the CH65.2C crossovers according to the system layout. Confirm the required speaker depth before final fairing assembly. Configure DSP crossovers and output levels for the CH65.2C speakers. Set amplifier gain and limiters using clean measured output. Secure all wiring against vibration, heat and sharp edges. Professional installation and DSP tuning are strongly recommended. Complete System Specifications Complete System SKU 24FLXPCH-4X2RG Vehicle Application Compatible 2024 and newer Harley-Davidson Road Glide Amplifier FLX700.4PRO four-channel amplifier with built-in DSP Amplifier Output at 2Ω 175W RMS × 4 channels at 14.4V Included Speaker Count Two Coaxial Horn speakers Included Speakers Two CH65.2C 6.5-inch speakers Speaker Impedance 2Ω per included speaker Loaded Amplifier Channels Two channels at 2Ω each Rear Amplified Channels Available for compatible future speakers Factory-Radio Interface NAV-TV ZEN-H A2B interface with Cicada harness Front Grilles 24CHDRGG Road Glide fairing grilles Power Wiring HDPG6K 6-AWG power and ground kit Rear Output Wiring 24HDRO plug-and-play harness Amplifier Rack 24HDAR-RG Road Glide amplifier rack Rear Speakers Included No Saddlebag Mounting Kit Included No Shopify Variants None Fitment and Ordering Notes Verify fitment: Confirm the exact Road Glide year, trim, factory radio, factory amplifier configuration, fairing speaker location and electrical system before ordering. Designed for compatible 2024 and newer Road Glide motorcycles. The package includes two 2-ohm front speakers. The package does not include selectable speaker impedance options. Two amplifier channels power the included front speaker pair. The remaining amplified channels are available for future expansion. The rear-output harness is included. Rear speakers and saddlebag mounting components are not included. No saddlebag cutting is required for the supplied front-only system. Future rear installation requirements depend on the selected mounting system. DSP configuration, crossover setup and output limiting are required. Professional installation and tuning are strongly recommended. Best For Compatible 2024+ Road Glide front-speaker upgrades Riders starting with a two-speaker amplified system Factory A2B radios requiring aftermarket amplifier integration High-efficiency 2-ohm Coaxial Horn speakers Systems requiring built-in DSP tuning and crossover control Riders planning to add rear speakers later Professional Road Glide audio installations Related Motorcycle Audio Categories Cicada and 2024+ Harley Audio Shop Cicada Audio 2023.5+ / 2024+ Harley Plug-and-Play Kits Shop Motorcycle Speakers System Support Motorcycle Amplifiers Motorcycle Amplifier Parts Motorcycle DSP and Signal Integration Installation Support Motorcycle Audio Installation in Taylors, SC Request a Custom Audio Build Motorcycle Audio Batteries Cicada 24FLXPCH-4X2RG FAQ What impedance are the included speakers? Both included CH65.2C speakers have a nominal impedance of 2 ohms. How many speakers are included? The system includes two 6.5-inch CH65.2C Coaxial Horn speakers for the Road Glide fairing. What load does the amplifier see? Each included speaker is connected to its own amplifier channel, so each loaded front channel operates at a nominal 2-ohm load. Are all four amplifier channels used? No. The supplied package uses two amplified channels for the front speakers. The other two channels remain available for a compatible rear-speaker upgrade. How much power does the amplifier produce? The FLX700.4PRO produces up to 175 watts RMS × 4 at 2 ohms, 120 watts RMS × 4 at 4 ohms or 350 watts RMS × 2 bridged at 4 ohms. Does the amplifier include a DSP? Yes. The FLX700.4PRO includes a six-channel DSP with four amplified channels and two processed pass-through channels. Why does the package use a non-DSP ZEN-H interface? The ZEN-H interface extracts the factory A2B signal. DSP processing is then performed inside the FLX700.4PRO amplifier. Are Road Glide fairing grilles included? Yes. The package includes the Cicada Audio 24CHDRGG powder-coated steel fairing grille pair. Is the amplifier rack included? Yes. The package includes the 24HDAR-RG Road Glide amplifier rack and mounting hardware. Is rear-speaker wiring included? Yes. The 24HDRO rear-output harness is included for future rear-speaker expansion. Are rear speakers included? No. The system is rear-speaker ready, but rear speakers and their saddlebag mounting components must be purchased separately. Do the saddlebags need to be cut for this two-speaker kit? No saddlebag modification is required for the supplied front-only system. A future rear-speaker upgrade may require cutting or other modification depending on the selected mounting solution. Does the system require tuning? Yes. The amplifier DSP, crossover frequencies, equalization, limiters and gain structure must be configured for the included speakers and any future rear-speaker expansion. Need Help Planning Your Road Glide System? Submit your Road Glide year, trim, factory audio package and future rear-speaker plans so Garage Bagger Stereo can verify fitment, electrical requirements and the correct expansion components for your motorcycle. Installation Services Request a Custom Build -
Cicada Audio 24FLXPCH-4X2SG 700W DSP 2-Speaker System for 2024+ Street Glide
Vendor:Cicada AudioCOMPLETE 2024+ STREET GLIDE FRONT AUDIO SYSTEM Cicada Audio 24FLXPCH-4X2SG 700W DSP 2-Speaker System The Cicada Audio 24FLXPCH-4X2SG is a complete front-fairing audio package for compatible 2024 and newer Harley-Davidson Street Glide motorcycles. It combines a four-channel amplifier with built-in DSP, two high-efficiency 2-ohm Coaxial Horn speakers, factory A2B radio integration, Street Glide-specific mounting components and a rear-output harness for future system expansion. See Everything Included View Speaker Load Front System with Rear Expansion Support Designed for compatible 2024+ Street Glide motorcycles FLX700.4PRO amplifier with built-in six-channel DSP 175 watts RMS × 4 channels at 2Ω Two CH65.2C 6.5-inch Coaxial Horn speakers Both included speakers are 2Ω Street Glide fairing grilles included NAV-TV ZEN-H A2B factory-radio integration Street Glide amplifier rack included 6-AWG amplifier power kit included Rear-output harness included for future expansion 24FLXPCH-4X2SG Complete System Overview This Cicada Audio package upgrades the two factory Street Glide fairing speaker locations while establishing the amplifier, DSP, power wiring and signal-integration foundation needed for a larger four-channel system. One pair of CH65.2C 6.5-inch Coaxial Horn speakers installs behind the included Cicada-branded Street Glide fairing grilles. Each speaker has a nominal impedance of 2 ohms and connects to its own amplifier channel. The included FLX700.4PRO provides four amplified DSP channels. The base package uses two channels for the front speakers, while the included 24HDRO harness prepares the system for a separately purchased rear-speaker upgrade. Speaker Impedance and Amplifier Channel Load Front Left: 2Ω One CH65.2C speaker connects to the assigned left-front amplifier channel and presents a nominal 2-ohm load. Front Right: 2Ω The second CH65.2C speaker connects to the assigned right-front amplifier channel and presents a nominal 2-ohm load. Rear Channels: Available No rear speakers are included. The other two amplified channels can support a properly matched future rear-speaker system. Included Speaker Count Two speakers / one pair Included Speaker Model CH65.2C Speaker Impedance 2Ω per speaker Base Configuration One 2Ω speaker on each of two amplifier channels Unused Amplified Channels Two channels available for compatible rear-speaker expansion Base-system load: Only two amplifier channels are loaded by the included system. Each loaded channel operates at a nominal 2 ohms. Rear-speaker impedance must be matched correctly before using the other two channels. Everything Included in the Complete System FLX700.4PRO — Four-Channel DSP Amplifier One compact Class-D amplifier producing up to 175 watts RMS × 4 channels at 2 ohms. It includes a six-channel DSP with four internally amplified channels and two processed pass-through outputs. CH65.2C — 6.5" Coaxial Horn Speakers One pair of 2-ohm Larry Frederick Classic Coaxial Horn speakers for the Street Glide fairing. Each speaker is rated for 250 watts RMS and includes an external 12dB crossover. 24CHDSGG — Street Glide Fairing Grilles One pair of Cicada Audio-branded, powder-coated steel fairing grilles designed for compatible 2024 and newer Street Glide motorcycles. 24HDAR-SG — Street Glide Amplifier Rack Black-anodized aluminum amplifier mounting rack that uses compatible OEM amplifier locations and includes predrilled FLX mounting points and installation hardware. HDPG6K — 6-AWG Amplifier Power Kit Includes six-foot power and ground cables with braided covering, battery-side ring terminals, amplifier-side ferrules, remote trigger wiring, a waterproof Mini-ANL fuse holder and multiple fuse values. 24HDZENHCAKIT — NAV-TV ZEN-H A2B Interface NAV-TV ZEN-H factory A2B interface with a Cicada Audio direct-connect amplifier harness and correctly pinned locking Molex connections. 24HDRO — Rear Output Speaker Harness Plug-and-play rear-output harness with factory-style connectors, two short extensions and two longer speaker-wire leads for future rear-speaker installation. Rear-speaker ready: The rear-output harness is included, but rear speakers, saddlebag speaker mounting parts and a saddlebag lid cut-in kit are not included with 24FLXPCH-4X2SG. FLX700.4PRO Amplifier and DSP 175W × 4 at 2Ω The amplifier produces up to 175 watts RMS on each of four channels when operating at 2 ohms and 14.4 volts. 120W × 4 at 4Ω It also supports four-channel operation with compatible 4-ohm speakers for systems designed around that channel load. 350W × 2 Bridged The published bridged configuration is 350 watts RMS × 2 into compatible 4-ohm loads. Six-Channel DSP Four DSP channels feed the internal amplifier, while two additional processed channels provide pass-through outputs for expansion. Bluetooth and USB-C Bluetooth audio streaming and USB-C computer connectivity support audio playback and compatible PC-based DSP configuration. Compact Motorcycle Chassis The micro-sized aluminum chassis is designed for limited fairing and rack space while using conformal-coated circuitry for protection. FLX700.4PRO Amplifier Specifications Amplifier Model FLX700.4PRO Amplifier Type Four-channel Class-D amplifier with built-in DSP Output at 4Ω 120W RMS × 4 channels at 14.4V Output at 2Ω 175W RMS × 4 channels at 14.4V Bridged Output at 4Ω 350W RMS × 2 channels at 14.4V DSP Channels Six total: four amplified and two pass-through Bluetooth Audio Included PC DSP Connection USB-C Operating Voltage 9V–16V Music Current Draw 50A Maximum Current Draw 80A Recommended Fuse 50A Efficiency 80% Frequency Response 20Hz–20kHz ±3dB Signal-to-Noise Ratio 91dB A-weighted Damping Factor 200 Input Sensitivity 0.2V–12V Turn-On Modes REM / DC / VOX Dimensions with Brackets 5.3 × 4.9 × 2.0 inches / 134 × 125 × 51mm Chassis Dimensions 4.1 × 4.9 × 2.0 inches / 104 × 125 × 51mm CH65.2C Front Fairing Speakers Speaker Model CH65.2C Quantity Two speakers / one pair Speaker Type 6.5-inch Larry Frederick Classic Coaxial Horn Nominal Impedance 2Ω per speaker Power Handling 250W RMS / 500W maximum per speaker Mid-Bass Voice Coil 2 inches / 51mm Tweeter Voice Coil 1.4 inches / 36mm Tweeter Dome Aluminum Cone Water-resistant treated paper Magnet N35SH neodymium External Crossover 12dB at 4kHz Sensitivity 96.4dB, 1W / 1M Frequency Response 75Hz–20kHz ±5dB Mounting Depth 3.0 inches / 76.2mm Mounting Diameter 5.7 inches / 145.5mm Warranty Two-year manufacturer warranty Rear-Speaker-Ready System Design The FLX700.4PRO is a four-channel amplifier, but the base package includes only the two front fairing speakers. Cicada includes the 24HDRO harness so compatible rear speakers can be added later without replacing the original amplifier or rebuilding the complete signal path. Included for Expansion Two additional amplified channels 24HDRO rear-output harness Factory-style harness connections Long speaker-wire leads for saddlebag routing Not Included Rear saddlebag speakers Saddlebag lid speaker adapters Cut-in speaker-lid hardware Rear speaker grilles or pods Expansion planning: Any added rear speakers must be compatible with the amplifier’s supported impedance, available power, crossover configuration and overall electrical system. Factory A2B Radio Integration The NAV-TV ZEN-H interface extracts the factory digital A2B audio signal. The included Cicada harness then routes that signal directly into the FLX700.4PRO through correctly pinned Molex connections. Designed for compatible 2024+ Harley-Davidson A2B systems No cutting or splicing of the factory signal harness Positive-locking automotive-grade connectors Direct connection to compatible Cicada Audio amplifiers Compact routing inside the Street Glide fairing DSP processing handled by the FLX700.4PRO amplifier System distinction: The included ZEN-H is the non-DSP interface configuration. The digital signal processing, tuning, crossovers and channel control are provided by the FLX700.4PRO. Installation and System Setup Mount the amplifier securely on the included 24HDAR-SG rack. Use the included HDPG6K power and ground wiring kit. Install the correctly rated fuse near the battery connection. Use the included A2B interface and Cicada amplifier harness. Install the CH65.2C crossovers according to the system layout. Confirm 3.0 inches of speaker mounting depth before final assembly. Configure DSP crossovers and output levels for the CH65.2C speakers. Set amplifier gain and limiters using clean measured output. Secure all wiring against vibration, heat and sharp edges. Professional installation and DSP tuning are strongly recommended. Complete System Specifications Complete System SKU 24FLXPCH-4X2SG Vehicle Application Compatible 2024 and newer Harley-Davidson Street Glide Amplifier FLX700.4PRO four-channel amplifier with built-in DSP Amplifier Output at 2Ω 175W RMS × 4 channels at 14.4V Included Speaker Count Two Coaxial Horn speakers Included Speakers Two CH65.2C 6.5-inch speakers Speaker Impedance 2Ω per included speaker Base Loaded Channels Two amplifier channels at 2Ω each Rear Amplified Channels Available for compatible future speakers Factory-Radio Interface NAV-TV ZEN-H A2B interface with Cicada harness Front Grilles 24CHDSGG Street Glide fairing grilles Power Wiring HDPG6K 6-AWG power and ground kit Rear Output Wiring 24HDRO plug-and-play harness Amplifier Rack 24HDAR-SG Street Glide amplifier rack Rear Speakers Included No Saddlebag Lid Kit Included No Shopify Variants None Fitment and Ordering Notes Verify fitment: Confirm the exact Street Glide year, trim, factory radio, factory amplifier configuration, fairing speaker location and electrical system before ordering. Designed for compatible 2024 and newer Street Glide motorcycles. The package includes two 2-ohm front speakers. The package does not include selectable speaker impedance options. Two amplifier channels power the included front speaker pair. The remaining amplified channels are available for future expansion. The rear-output harness is included. Rear speakers and saddlebag mounting components are not included. DSP configuration, crossover setup and output limiting are required. Professional installation and tuning are strongly recommended. Best For Compatible 2024+ Street Glide front-speaker upgrades Riders starting with a two-speaker amplified system Factory A2B radios requiring aftermarket amplifier integration High-efficiency 2-ohm Coaxial Horn speakers Systems requiring built-in DSP tuning and crossover control Riders planning to add rear speakers later Professional Street Glide audio installations Related Motorcycle Audio Categories Cicada and 2024+ Harley Audio Shop Cicada Audio 2023.5+ / 2024+ Harley Plug-and-Play Kits Shop Motorcycle Speakers System Support Motorcycle Amplifiers Motorcycle Amplifier Parts Motorcycle DSP and Signal Integration Installation Support Motorcycle Audio Installation in Taylors, SC Request a Custom Audio Build Motorcycle Audio Batteries Cicada 24FLXPCH-4X2SG FAQ What impedance are the included speakers? Both included CH65.2C speakers have a nominal impedance of 2 ohms. How many speakers are included? The system includes two 6.5-inch CH65.2C Coaxial Horn speakers for the Street Glide fairing. What load does the amplifier see? Each included speaker is connected to its own amplifier channel, so each loaded front channel operates at a nominal 2-ohm load. Are all four amplifier channels used? No. The base package uses two amplified channels for the two front speakers. The other two channels remain available for a compatible rear-speaker upgrade. How much power does the amplifier produce? The FLX700.4PRO produces up to 175 watts RMS × 4 at 2 ohms or 120 watts RMS × 4 at 4 ohms when supplied with 14.4 volts. Does the amplifier include a DSP? Yes. The FLX700.4PRO includes a six-channel DSP with four amplified channels and two processed pass-through channels. Why does the package use a non-DSP ZEN-H interface? The ZEN-H interface extracts the factory A2B signal. DSP processing is then performed inside the FLX700.4PRO amplifier. Are Street Glide fairing grilles included? Yes. The package includes the Cicada Audio 24CHDSGG powder-coated steel fairing grille pair. Is the amplifier rack included? Yes. The package includes the 24HDAR-SG Street Glide amplifier rack and its mounting hardware. Is rear-speaker wiring included? Yes. The 24HDRO rear-output harness is included for future rear-speaker expansion. Are rear speakers included? No. The system is rear-speaker ready, but rear speakers and their saddlebag mounting components must be purchased separately. Does the system require tuning? Yes. The amplifier DSP, crossover frequencies, equalization, limiters and gain structure must be configured for the included speakers and any future rear-speaker expansion. Need Help Planning Your Street Glide System? Submit your Street Glide year, trim, factory audio package and future rear-speaker plans so Garage Bagger Stereo can verify fitment, electrical requirements and the correct expansion components for your motorcycle. Installation Services Request a Custom Build -
Cicada Audio 24FLXPCH-4X4RG 1400W DSP 4-Speaker System for 2024+ Road Glide
Vendor:Cicada AudioCOMPLETE 2024+ ROAD GLIDE DSP AUDIO SYSTEM Cicada Audio 24FLXPCH-4X4RG 1400W DSP 4-Speaker System Build a complete high-output audio system in a compatible 2024 and newer Harley-Davidson Road Glide with four Cicada Audio coaxial horn speakers, a four-channel DSP amplifier and direct factory A2B radio integration. The package powers two 6.5-inch front fairing speakers and two 6×9-inch saddlebag speakers from four dedicated amplifier channels. Road Glide grilles, an amplifier rack, a saddlebag lid cut-in system, power wiring and rear-output wiring are included for the complete installation. See Everything Included View Speaker Configuration Complete Four-Speaker Road Glide System Designed for compatible 2024+ Road Glide motorcycles FLX1400.4PRO amplifier with six-channel DSP 225 watts RMS × 4 channels at 4 ohms Two CH65.4C 6.5-inch fairing speakers Two CH69.4W 6×9 saddlebag speakers All four included speakers are 4 ohms Road Glide fairing grilles included 2024+ saddlebag lid cut-in kit included NAV-TV ZEN-H A2B integration included 4-AWG amplifier power kit included Rear-output wiring harness included Road Glide amplifier rack included 24FLXPCH-4X4RG Complete System Overview The Cicada Audio 24FLXPCH-4X4RG combines the primary audio, integration, wiring and mounting components required to create a complete amplified four-speaker system in a compatible 2024 and newer Harley-Davidson Road Glide. Two CH65.4C 6.5-inch coaxial horn speakers install in the Road Glide front fairing. Two CH69.4W 6×9-inch coaxial horn speakers install in the factory saddlebag lids using the included 24CHDLID cut-in mounting system. The FLX1400.4PRO powers all four speakers and supplies the crossover, equalization, time alignment and output-control functions required to tune the complete motorcycle audio system. Four-speaker DSP configuration: This bundle uses four 4-ohm speakers. Do not substitute the 2-ohm CHX65.2 or CHX69.2 speaker configuration used in the standard non-DSP package without redesigning the amplifier load and DSP tune. Four-Channel Speaker and Amplifier Configuration Front Fairing Channels Two CH65.4C 6.5-inch speakers create the Road Glide front soundstage. Each speaker presents a nominal 4-ohm load to its own FLX1400.4PRO amplifier channel. Rear Saddlebag Channels Two CH69.4W 6×9-inch speakers create the rear soundstage. Each saddlebag speaker presents a nominal 4-ohm load to its own amplifier channel. Channel 1 Front-left CH65.4C — 4Ω Channel 2 Front-right CH65.4C — 4Ω Channel 3 Rear-left CH69.4W — 4Ω Channel 4 Rear-right CH69.4W — 4Ω Amplifier Output 225W RMS per channel at 4Ω Speaker RMS Rating 250W RMS per speaker Unused Amplified Channels None DSP Pass-Through Outputs Two processed channels for compatible future expansion Power matching: The amplifier supplies 225 watts RMS to each 4-ohm speaker channel. Each included speaker is rated for 250 watts RMS. Correct gain, crossover, limiter and DSP settings are still required for reliable operation. Everything Included in the Complete System FLX1400.4PRO DSP Amplifier One four-channel Class-D amplifier with four amplified DSP channels, two processed pass-through channels, Bluetooth audio streaming and USB-C computer tuning. CH65.4C Fairing Speaker Pair Two 4-ohm Larry Frederick Classic 6.5-inch coaxial horn speakers for the Road Glide front fairing. CH69.4W Saddlebag Speaker Pair Two 4-ohm 6×9-inch all-weather coaxial horn speakers for the rear saddlebag lid locations. 24CHDRGG Road Glide Grilles Powder-coated steel front fairing grilles with Cicada Audio-branded emblems for compatible 2024+ Road Glide motorcycles. 24CHDLID Saddlebag Lid Kit Complete 2024+ cut-in mounting system with angled top-load 6×9 baffles, powder-coated steel grilles, clamping rings, gaskets, cutting templates, rain covers and crossover-storage tethers. HDPG4K 4-AWG Power Kit Heavy-gauge power and ground wiring, Harley-compatible remote trigger wiring, waterproof Mini-ANL fuse holder and multiple fuse values. 24HDZENHCAKIT A2B Interface NAV-TV ZEN-H factory A2B interface with a Cicada Audio direct-connect harness and positive-locking Molex connections. 24HDRO Rear-Output Harness Plug-and-play rear-speaker harness with factory-style connectors, short extensions and longer leads for routing audio to the saddlebags. 24HDAR-RG Amplifier Rack Black-anodized aluminum amplifier rack designed for compatible OEM Road Glide mounting locations and Cicada FLX-style amplifiers. FLX1400.4PRO Six-Channel DSP Amplifier The FLX1400.4PRO combines a high-power four-channel Class-D amplifier with six channels of digital signal processing. Four DSP channels feed the internal amplifier, while two processed pass-through outputs can feed compatible future amplifiers. 225W × 4 at 4Ω Supplies 225 watts RMS to each included 4-ohm coaxial horn speaker. 350W × 4 at 2Ω Supports compatible 2-ohm configurations when the complete speaker and tuning design is changed accordingly. 700W × 2 Bridged The published bridged output is 700 watts RMS × 2 into compatible 4-ohm loads. Six DSP Channels Four amplified and two pass-through DSP channels support precise system control and later expansion. Bluetooth Streaming Built-in Bluetooth audio streaming provides a direct source for compatible tuning, testing and playback. USB-C Computer Tuning USB-C connectivity supports PC-based DIALD DSP configuration and detailed system tuning. FLX1400.4PRO Amplifier Specifications Amplifier Model FLX1400.4PRO Amplifier Type Four-channel Class-D amplifier with six-channel DSP DSP Configuration Four amplified channels and two pass-through channels Output at 4Ω 225W RMS × 4 channels at 14.4V Output at 2Ω 350W RMS × 4 channels at 14.4V Bridged Output at 4Ω 700W RMS × 2 channels at 14.4V Frequency Response 20Hz–20kHz ±3dB Signal-to-Noise Ratio 91dB A-weighted Damping Factor 200 THD + Noise 0.1% at 2Ω per channel at 10% rated power Efficiency 80% Crossover Modes High-pass, band-pass and low-pass Crossover Range 20Hz–20kHz Crossover Slopes 6, 12, 24 or 48dB per octave Input Sensitivity 0.2V–12V Operating Voltage 9V–16V Music Current Draw 70A Maximum Current Draw 150A Recommended Fuse 100A for the published music-load specification Power Input 4-AWG Speaker Outputs 12-AWG busbar-style terminals Turn-On Modes REM, DC or VOX Dimensions with Brackets 8.26 × 4.9 × 2 inches / 210 × 125 × 51mm Chassis Dimensions 7.1 × 4.9 × 2 inches / 180 × 125 × 51mm CH65.4C Front Fairing Speakers The CH65.4C pair uses Cicada Audio’s Larry Frederick Classic coaxial horn design. Each speaker combines a 6.5-inch mid-bass driver, aluminum horn tweeter and an external 12dB crossover. Speaker Model CH65.4C Quantity Two speakers / one pair Nominal Size 6.5 inches Nominal Impedance 4Ω per speaker Power Handling 250W RMS / 500W maximum per speaker Mid-Bass Voice Coil 2 inches / 51mm Tweeter Voice Coil 1.4 inches / 36mm Tweeter Dome Aluminum Cone Water-resistant treated paper Magnet N35SH neodymium Crossover External 12dB crossover at 4kHz Sensitivity 96.4dB, 1W / 1m Frequency Response 75Hz–20kHz ±5dB Mounting Depth 3 inches / 76.2mm Mounting Diameter 5.7 inches / 145.5mm CH69.4W Saddlebag Speakers The CH69.4W pair provides high-output rear audio from the Road Glide saddlebag lids. Each speaker combines a water-resistant treated-paper cone, aluminum horn tweeter, external crossover and neodymium motor. Speaker Model CH69.4W Quantity Two speakers / one pair Nominal Size 6×9 inches Nominal Impedance 4Ω per speaker Power Handling 250W RMS / 500W maximum per speaker Mid-Bass Voice Coil 2.5 inches / 64mm Tweeter Voice Coil 1.4 inches / 36mm Tweeter Dome Aluminum Cone Water-resistant treated paper Magnet N35SH neodymium Crossover External 12dB crossover with -3dB and -6dB tweeter attenuation Sensitivity 95dB Frequency Response 75Hz–20kHz ±3dB Mounting Depth 3.7 inches / 93mm Mounting Opening 6.6 × 9.3 inches / 155 × 226mm Built-In DSP and System Tuning Front and Rear Crossovers Configure independent filtering for the 6.5-inch front speakers and 6×9-inch rear speakers. Equalization Shape the system response around the Road Glide fairing, saddlebag locations and open-air riding environment. Time Alignment Correct arrival-time differences between the front and rear speaker locations for a more coherent soundstage. Output Limiting Control maximum clean output to protect the speakers from clipping, thermal stress and excessive mechanical excursion. Tweeter-Level Control Combine DSP adjustment with the external crossover attenuation options to balance upper-frequency projection. Future Expansion Two processed pass-through outputs can support a compatible additional amplifier for later system expansion. Professional tuning recommended: The correct DSP settings depend on speaker placement, acoustic loading, desired listening level and the motorcycle’s complete electrical and audio configuration. NAV-TV A2B Signal Integration The included 24HDZENHCAKIT uses the NAV-TV ZEN-H to extract the compatible factory Harley-Davidson A2B audio signal. Cicada’s direct-connect harness routes the signal into the FLX1400.4PRO through correctly pinned locking connectors. Compatible 2024+ Harley-Davidson A2B factory signal integration No cutting or splicing of the factory signal harness Correctly pinned Cicada amplifier connections Automotive-grade materials and locking connectors Compact routing inside the Road Glide fairing Stable signal delivery to the DSP amplifier DSP clarification: The included ZEN-H interface is the non-DSP version. The FLX1400.4PRO amplifier provides the system’s digital signal processing. 24CHDLID Saddlebag Lid Installation The included 24CHDLID system converts compatible 2024 and newer factory Harley-Davidson saddlebag lids into top-load 6×9-inch speaker locations. The angled baffles direct the rear-speaker output toward the rider. Top-Load Baffle System The speaker installs from the top of the lid for easier service and improved support of full-depth 6×9-inch drivers. Steel Speaker Grilles Heavy-duty powder-coated steel mesh protects the rear speakers from contact and debris. Gasketed Clamp System Clamping rings and gaskets help seal the completed openings against water intrusion and unwanted rattles. Precision Templates Molded cutting templates support accurate placement of the permanent saddlebag lid openings. Rain Covers Rainproof lid covers provide additional speaker protection while the motorcycle is parked or being washed. Crossover Pouches and Tethers Included lid tethers and crossover-storage pouches support a secure, organized rear-speaker installation. Permanent saddlebag modification required: Both factory lids must be cut for the included rear-speaker system. Verify template placement, speaker clearance and wiring before making any permanent modifications. Road Glide Grilles and Amplifier Rack 24CHDRGG Fairing Grilles Powder-coated steel grilles are engineered for compatible 2024+ Road Glide front speaker locations and include Cicada Audio-branded emblems. 24HDAR-RG Amplifier Rack The black-anodized aluminum rack uses compatible OEM amplifier mounting locations and predrilled holes for FLX-style amplifiers. Power Wiring and Fuse Protection The HDPG4K includes six-foot 4-AWG power and ground cables with braided covering, battery-side ring terminals, amplifier-side ferrules, remote trigger wiring and a waterproof Mini-ANL fuse holder. Power Cable 4-AWG with battery ring terminal and amplifier ferrule Ground Cable 4-AWG with battery ring terminal and amplifier ferrule Remote Trigger Harley-compatible trigger lead Fuse Holder Waterproof Mini-ANL Included Fuse Values 60A, 80A and 100A Amplifier Recommendation 100A for the published FLX1400.4PRO music-load specification Electrical-system inspection required: Verify the motorcycle battery, charging output, cable routing, ground quality and fuse installation before operating the system at high output. Complete System Specifications Complete System SKU 24FLXPCH-4X4RG Vehicle Application Compatible 2024 and newer Harley-Davidson Road Glide Amplifier FLX1400.4PRO four-channel amplifier with six-channel DSP Amplifier Output at 4Ω 225W RMS × 4 channels Front Speakers Two CH65.4C 6.5-inch coaxial horn speakers Rear Speakers Two CH69.4W 6×9-inch coaxial horn speakers Speaker Impedance 4Ω per speaker Speaker Power Handling 250W RMS / 500W maximum per speaker Loaded Amplifier Channels All four channels at 4Ω each DSP Pass-Through Channels Two Factory Signal Interface NAV-TV ZEN-H non-DSP A2B interface with Cicada harness Front Grilles 24CHDRGG Road Glide fairing grilles Rear Mounting System 24CHDLID 2024+ saddlebag lid cut-in kit Rear Speaker Wiring 24HDRO plug-and-play harness Power Wiring HDPG4K 4-AWG installation kit Amplifier Rack 24HDAR-RG Road Glide amplifier rack Saddlebag Cutting Required Yes Shopify Variants None Fitment and Ordering Notes Confirm the complete motorcycle configuration: Verify the Road Glide year, trim, factory radio, factory amplifier, A2B audio system, saddlebag type and electrical condition before ordering. Designed for compatible 2024 and newer Road Glide motorcycles. The package includes four 4-ohm speakers. All four amplifier channels are used in the supplied configuration. Each speaker connects to its own amplifier channel. The FLX1400.4PRO supplies the system DSP processing. The included NAV-TV ZEN-H is the non-DSP A2B interface. The front Road Glide fairing grilles are included. The rear saddlebag lid cut-in mounting system is included. Both factory saddlebag lids require permanent cutting. Rear speaker wiring is included. Professional installation and DSP tuning are strongly recommended. Best For Compatible 2024+ Road Glide complete audio upgrades Riders wanting front fairing and saddlebag speakers Factory A2B radio systems requiring aftermarket integration Four-channel systems using matched 4-ohm speaker loads High-output coaxial horn motorcycle audio systems Systems requiring built-in DSP tuning and output control Professional Road Glide audio installations Related Motorcycle Audio Categories Cicada and 2024+ Harley Audio Shop Cicada Audio 2023.5+ / 2024+ Harley Plug-and-Play Kits Shop Motorcycle Speakers Amplifier and Signal Support Motorcycle Amplifiers Motorcycle Amplifier Parts Motorcycle DSP and Signal Integration Installation Support Motorcycle Audio Installation in Taylors, SC Request a Custom Audio Build Motorcycle Audio Batteries Cicada 24FLXPCH-4X4RG FAQ How many speakers are included? The system includes four speakers: two CH65.4C 6.5-inch fairing speakers and two CH69.4W 6×9-inch saddlebag speakers. What impedance are the included speakers? Every included speaker has a nominal impedance of 4 ohms. Are these the 2-ohm CHX speakers? No. The official DSP bundle specifies 4-ohm CH65.4C and CH69.4W coaxial horn speakers. How much power does each speaker receive? The FLX1400.4PRO supplies up to 225 watts RMS to each speaker channel at 4 ohms. How much power can each speaker handle? Each included speaker is rated for 250 watts RMS and 500 watts maximum. Are all four amplifier channels used? Yes. Two channels power the front speakers and two channels power the rear saddlebag speakers. Are any DSP outputs available for expansion? Yes. The amplifier provides two processed pass-through DSP outputs for a compatible future external amplifier. Does the amplifier include DSP? Yes. The FLX1400.4PRO contains six DSP channels: four amplified and two pass-through channels. Does the NAV-TV interface include DSP? No. The package uses the non-DSP ZEN-H interface for factory A2B signal integration. The Cicada amplifier performs the DSP processing. Are Road Glide fairing grilles included? Yes. Cicada 24CHDRGG powder-coated steel front grilles are included. Are saddlebag speaker mounts included? Yes. The complete 24CHDLID 6×9-inch saddlebag lid cut-in system is included. Do the factory saddlebag lids need to be cut? Yes. The included rear-speaker system requires permanent modification of both factory saddlebag lids. Is rear-speaker wiring included? Yes. The package includes the 24HDRO plug-and-play rear-output harness. What fuse does the amplifier require? Cicada publishes a 100-amp recommended fuse for the FLX1400.4PRO music-load specification. The included HDPG4K kit includes a 100-amp fuse. Is the Road Glide amplifier rack included? Yes. The package includes the 24HDAR-RG black-anodized aluminum amplifier rack and mounting hardware. Is professional tuning recommended? Yes. The front and rear speaker locations, external crossovers, amplifier output and high-power operating levels make professional DSP setup strongly recommended. Need Help Planning Your Road Glide System? Garage Bagger Stereo can help verify Road Glide fitment, speaker impedance selection, amplifier matching, fairing and saddlebag mounting, power and speaker wiring, and factory A2B signal integration before the system is installed. Installation Services Request a Custom Build -
Cicada Audio 24FLXPCH-4X4SG 1400W DSP 4-Speaker System for 2024+ Street Glide
Vendor:Cicada AudioCOMPLETE 2024+ STREET GLIDE DSP AUDIO SYSTEM Cicada Audio 24FLXPCH-4X4SG 1400W DSP 4-Speaker System Build a complete high-output audio system in a compatible 2024 and newer Harley-Davidson Street Glide with four Cicada Audio coaxial horn speakers, a powerful four-channel DSP amplifier and direct factory A2B radio integration. The package powers two 6.5-inch fairing speakers and two 6×9-inch saddlebag speakers from four dedicated amplifier channels. It also includes the Street Glide grilles, amplifier rack, saddlebag lid cut-in system, power wiring and rear-output harness required for the complete installation. See Everything Included View Speaker Configuration Complete Four-Speaker System Designed for compatible 2024+ Street Glide motorcycles FLX1400.4PRO amplifier with six-channel DSP 225 watts RMS × 4 channels at 4 ohms Two CH65.4C 6.5-inch fairing speakers Two CH69.4W 6×9 saddlebag speakers All four included speakers are 4 ohms Street Glide fairing grilles included 2024+ saddlebag lid cut-in kit included NAV-TV ZEN-H A2B integration included 4-AWG amplifier power kit included Rear-output wiring harness included Street Glide amplifier rack included 24FLXPCH-4X4SG Complete System Overview The Cicada Audio 24FLXPCH-4X4SG combines the main audio, integration, wiring and mounting components required to create a complete amplified four-speaker system in a compatible 2024 and newer Harley-Davidson Street Glide. Two CH65.4C 6.5-inch coaxial horn speakers install in the front fairing. Two CH69.4W 6×9 coaxial horn speakers install in the factory saddlebag lids using the included 24CHDLID cut-in mounting system. The FLX1400.4PRO powers all four speakers and provides the crossover, equalization, delay and output-control functions needed to tune the complete motorcycle audio system. Four-speaker DSP configuration: This package uses four 4-ohm speakers. Do not substitute the 2-ohm CHX65.2 or CHX69.2 speaker configuration used in the standard non-DSP package without redesigning and retuning the system. Four-Channel Speaker and Amplifier Configuration Front Fairing Channels Two CH65.4C 6.5-inch speakers power the Street Glide front soundstage. Each speaker presents a nominal 4-ohm load to its own FLX1400.4PRO amplifier channel. Rear Saddlebag Channels Two CH69.4W 6×9 speakers provide the rear soundstage. Each speaker presents a nominal 4-ohm load to its own amplifier channel. Channel 1 Front-left CH65.4C — 4Ω Channel 2 Front-right CH65.4C — 4Ω Channel 3 Rear-left CH69.4W — 4Ω Channel 4 Rear-right CH69.4W — 4Ω Amplifier Output 225W RMS per channel at 4Ω Speaker RMS Rating 250W RMS per speaker Unused Amplified Channels None DSP Pass-Through Outputs Two channels available for compatible future expansion Power matching: The amplifier supplies 225 watts RMS to each 4-ohm speaker channel. Each included speaker is rated for 250 watts RMS. Correct gain, crossover, limiter and DSP settings are still required for reliable operation. Everything Included in the Complete System FLX1400.4PRO DSP Amplifier One four-channel Class-D amplifier with four amplified DSP channels, two DSP pass-through channels, Bluetooth audio streaming and USB-C computer tuning. CH65.4C Fairing Speaker Pair Two 4-ohm Larry Frederick Classic 6.5-inch coaxial horn speakers for the Street Glide front fairing. CH69.4W Saddlebag Speaker Pair Two 4-ohm 6×9-inch all-weather coaxial horn speakers for the rear saddlebag lid locations. 24CHDSGG Street Glide Grilles Powder-coated steel front fairing grilles with Cicada Audio-branded emblems for compatible 2024+ Street Glide motorcycles. 24CHDLID Saddlebag Lid Kit Complete 2024+ cut-in mounting system with top-load 6×9 baffles, steel grilles, clamping rings, templates, gasketing, tethers and rain covers. HDPG4K 4-AWG Power Kit Heavy-gauge power and ground wiring, remote trigger wiring, waterproof Mini-ANL fuse holder and multiple fuse values. 24HDZENHCAKIT A2B Interface NAV-TV ZEN-H factory A2B interface with a Cicada Audio direct-connect harness and locking Molex connections. 24HDRO Rear-Output Harness Plug-and-play rear-speaker harness with factory-style connectors, extensions and longer leads for routing audio to the saddlebags. 24HDAR-SG Amplifier Rack Black-anodized aluminum amplifier rack designed for compatible OEM Street Glide mounting locations and Cicada FLX amplifiers. FLX1400.4PRO Six-Channel DSP Amplifier The FLX1400.4PRO combines a high-power four-channel Class-D amplifier with six channels of digital signal processing. Four DSP channels feed the internal amplifier, while two additional processed pass-through outputs can feed compatible future amplifiers. 225W × 4 at 4Ω Supplies 225 watts RMS to each included 4-ohm coaxial horn speaker. 350W × 4 at 2Ω Supports compatible future 2-ohm system configurations when the complete speaker and tuning design is changed accordingly. 700W × 2 Bridged at 4Ω The amplifier can also operate as a two-channel bridged amplifier with compatible 4-ohm loads. Six DSP Channels Four amplified and two pass-through DSP channels support precise system control and future expansion. Bluetooth Streaming Built-in Bluetooth audio streaming provides a direct audio source for compatible tuning and testing applications. USB-C Computer Tuning USB-C connectivity supports PC-based DIALD DSP configuration and system tuning. FLX1400.4PRO Amplifier Specifications Amplifier Model FLX1400.4PRO Amplifier Type Four-channel Class-D amplifier with six-channel DSP DSP Configuration Four amplified channels and two pass-through channels Output at 4Ω 225W RMS × 4 channels at 14.4V Output at 2Ω 350W RMS × 4 channels at 14.4V Bridged Output at 4Ω 700W RMS × 2 channels at 14.4V Frequency Response 20Hz–20kHz ±3dB Signal-to-Noise Ratio 91dB A-weighted Damping Factor 200 THD + Noise 0.1% at 2Ω per channel at 10% rated power Efficiency 80% Crossover Modes High-pass, band-pass and low-pass Crossover Range 20Hz–20kHz Crossover Slopes 6, 12, 24 or 48dB per octave Input Sensitivity 0.2V–12V Operating Voltage 9V–16V Music Current Draw 70A Maximum Current Draw 150A Recommended Fuse 100A for the published music-load specification Power Input 4-AWG Speaker Outputs 12-AWG busbar-style terminals Turn-On Modes REM, DC or VOX Dimensions with Brackets 8.26 × 4.9 × 2 inches / 210 × 125 × 51mm Chassis Dimensions 7.1 × 4.9 × 2 inches / 180 × 125 × 51mm CH65.4C Front Fairing Speakers The CH65.4C pair uses Cicada Audio’s Larry Frederick Classic coaxial horn design. Each speaker combines a 6.5-inch mid-bass driver, aluminum horn tweeter and external 12dB crossover. Speaker Model CH65.4C Quantity Two speakers / one pair Nominal Size 6.5 inches Nominal Impedance 4Ω per speaker Power Handling 250W RMS / 500W maximum per speaker Mid-Bass Voice Coil 2 inches / 51mm Tweeter Voice Coil 1.4 inches / 36mm Tweeter Dome Aluminum Cone Water-resistant treated paper Magnet N35SH neodymium Crossover External 12dB crossover at 4kHz Sensitivity 96.4dB, 1W / 1m Frequency Response 75Hz–20kHz ±5dB Mounting Depth 3 inches / 76.2mm Mounting Diameter 5.7 inches / 145.5mm CH69.4W Saddlebag Speakers The CH69.4W pair provides high-output rear audio from the Street Glide saddlebag lids. Each speaker combines a water-resistant treated-paper cone, aluminum horn tweeter, external crossover and neodymium motor. Speaker Model CH69.4W Quantity Two speakers / one pair Nominal Size 6×9 inches Nominal Impedance 4Ω per speaker Power Handling 250W RMS / 500W maximum per speaker Mid-Bass Voice Coil 2.5 inches / 64mm Tweeter Voice Coil 1.4 inches / 36mm Tweeter Dome Aluminum Cone Water-resistant treated paper Magnet N35SH neodymium Crossover External 12dB crossover with -3dB and -6dB attenuation options Sensitivity 95dB Frequency Response 75Hz–20kHz ±3dB Mounting Depth 3.7 inches / 93mm Mounting Opening 6.6 × 9.3 inches / 155 × 226mm Built-In DSP and System Tuning Front and Rear Crossovers Configure independent filtering for the 6.5-inch front speakers and 6×9-inch rear speakers. Equalization Shape the system response around the Street Glide fairing, saddlebag locations and open-air riding environment. Time Alignment Correct arrival-time differences between the front and rear speaker locations for a more coherent soundstage. Output Limiting Control maximum clean output to protect the speakers from clipping, thermal stress and excessive mechanical excursion. Tweeter-Level Control Combine DSP adjustment with the external crossover attenuation options to balance upper-frequency projection. Future Expansion Two processed pass-through outputs can support a compatible additional amplifier for later system expansion. Professional tuning recommended: The correct DSP settings depend on speaker placement, available acoustic loading, desired listening level and the motorcycle’s complete electrical and audio configuration. NAV-TV A2B Signal Integration The included 24HDZENHCAKIT uses the NAV-TV ZEN-H to extract the compatible factory Harley-Davidson A2B audio signal. Cicada’s direct-connect harness routes the signal into the FLX1400.4PRO through correctly pinned locking connectors. Compatible 2024+ Harley-Davidson A2B factory signal integration No cutting or splicing of the factory signal harness Correctly pinned Cicada amplifier connections Automotive-grade materials and locking connectors Compact routing inside the Street Glide fairing Stable signal delivery to the DSP amplifier DSP clarification: The included ZEN-H interface is the non-DSP version. The FLX1400.4PRO amplifier provides the system’s digital signal processing. 24CHDLID Saddlebag Lid Installation The included 24CHDLID system converts compatible 2024 and newer factory Harley-Davidson saddlebag lids into top-load 6×9-inch speaker locations. The angled baffles direct the rear-speaker output toward the rider. Top-Load Baffle System The speaker installs from the top of the lid for easier service and improved support of full-depth 6×9 drivers. Steel Speaker Grilles Heavy-duty powder-coated steel mesh protects the rear speakers from contact and debris. Waterproof Gasket System A clamping ring and gasket system help seal the completed opening against water intrusion. Precision Templates Molded cutting templates support accurate placement of the permanent saddlebag lid openings. Rain Covers Rainproof lid covers provide additional speaker protection while the motorcycle is parked or being washed. Crossover Pouches and Tethers Included lid tethers and crossover-storage pouches support a secure, organized rear-speaker installation. Permanent saddlebag modification required: Both factory lids must be cut for the included rear-speaker system. Verify template placement, speaker clearance and wiring before making any permanent modifications. Street Glide Grilles and Amplifier Rack 24CHDSGG Fairing Grilles Powder-coated steel grilles are engineered for compatible 2024+ Street Glide front speaker locations and include Cicada Audio logo emblems. 24HDAR-SG Amplifier Rack The black-anodized aluminum rack uses compatible OEM amplifier mounting locations and predrilled holes for the FLX1400.4PRO. Power Wiring and Fuse Protection The HDPG4K includes six-foot 4-AWG power and ground cables with braided covering, battery-side ring terminals, amplifier-side ferrules, remote trigger wiring and a waterproof Mini-ANL fuse holder. Power Cable 4-AWG with battery ring terminal and amplifier ferrule Ground Cable 4-AWG with battery ring terminal and amplifier ferrule Remote Trigger Harley-compatible trigger lead Fuse Holder Waterproof Mini-ANL Included Fuse Values 60A, 80A and 100A Amplifier Recommendation 100A for the published FLX1400.4PRO music-load specification Electrical-system inspection required: Verify the motorcycle battery, charging output, cable routing, ground quality and fuse installation before operating the system at high output. Complete System Specifications Complete System SKU 24FLXPCH-4X4SG Vehicle Application Compatible 2024 and newer Harley-Davidson Street Glide Amplifier FLX1400.4PRO four-channel amplifier with six-channel DSP Amplifier Output at 4Ω 225W RMS × 4 channels Front Speakers Two CH65.4C 6.5-inch coaxial horn speakers Rear Speakers Two CH69.4W 6×9-inch coaxial horn speakers Speaker Impedance 4Ω per speaker Speaker Power Handling 250W RMS / 500W maximum per speaker Loaded Amplifier Channels All four channels at 4Ω each DSP Pass-Through Channels Two Factory Signal Interface NAV-TV ZEN-H non-DSP A2B interface with Cicada harness Front Grilles 24CHDSGG Street Glide fairing grilles Rear Mounting System 24CHDLID 2024+ saddlebag lid cut-in kit Rear Speaker Wiring 24HDRO plug-and-play harness Power Wiring HDPG4K 4-AWG installation kit Amplifier Rack 24HDAR-SG Street Glide amplifier rack Saddlebag Cutting Required Yes Shopify Variants None Fitment and Ordering Notes Confirm the complete motorcycle configuration: Verify the Street Glide year, trim, factory radio, factory amplifier, A2B audio system, saddlebag type and electrical condition before ordering. Designed for compatible 2024 and newer Street Glide motorcycles. The package includes four 4-ohm speakers. All four amplifier channels are used in the supplied configuration. Each speaker is connected to its own amplifier channel. The FLX1400.4PRO supplies the system DSP processing. The included NAV-TV ZEN-H is the non-DSP A2B interface. The front fairing grilles are included. The rear saddlebag lid cut-in mounting system is included. Both factory saddlebag lids require permanent cutting. Rear speaker wiring is included. Professional installation and DSP tuning are strongly recommended. Best For Compatible 2024+ Street Glide complete audio upgrades Riders wanting front fairing and saddlebag speakers Factory A2B radio systems requiring aftermarket integration Four-channel systems using matched 4-ohm speaker loads High-output coaxial horn motorcycle audio systems Systems requiring built-in DSP tuning and output control Professional Street Glide audio installations Related Motorcycle Audio Categories Cicada and 2024+ Harley Audio Shop Cicada Audio 2023.5+ / 2024+ Harley Plug-and-Play Kits Shop Motorcycle Speakers Amplifier and Signal Support Motorcycle Amplifiers Motorcycle Amplifier Parts Motorcycle DSP and Signal Integration Installation Support Motorcycle Audio Installation in Taylors, SC Request a Custom Audio Build Motorcycle Audio Batteries Cicada 24FLXPCH-4X4SG FAQ How many speakers are included? The system includes four speakers: two CH65.4C 6.5-inch fairing speakers and two CH69.4W 6×9 saddlebag speakers. What impedance are the included speakers? Every included speaker has a nominal impedance of 4 ohms. Are these the 2-ohm CHX speakers? No. The current official bundle specifies 4-ohm CH65.4C and CH69.4W coaxial horn speakers. How much power does each speaker receive? The FLX1400.4PRO supplies up to 225 watts RMS to each speaker channel at 4 ohms. How much power can each speaker handle? Each included speaker is rated for 250 watts RMS and 500 watts maximum. Are all four amplifier channels used? Yes. Two channels power the front speakers and two channels power the rear saddlebag speakers. Are any DSP outputs available for expansion? Yes. The amplifier provides two processed pass-through DSP outputs for a compatible future external amplifier. Does the amplifier include DSP? Yes. The FLX1400.4PRO contains six DSP channels: four amplified and two pass-through channels. Does the NAV-TV interface include DSP? No. The package uses the non-DSP ZEN-H interface for factory A2B signal integration. The Cicada amplifier performs the DSP processing. Are Street Glide fairing grilles included? Yes. Cicada 24CHDSGG powder-coated steel front grilles are included. Are saddlebag speaker mounts included? Yes. The complete 24CHDLID 6×9 saddlebag lid cut-in system is included. Do the factory saddlebag lids need to be cut? Yes. The included rear-speaker system requires permanent modification of both factory saddlebag lids. Is rear-speaker wiring included? Yes. The package includes the 24HDRO plug-and-play rear-output harness. What fuse does the amplifier require? Cicada publishes a 100-amp recommended fuse for the FLX1400.4PRO music-load specification. The included HDPG4K kit includes a 100-amp fuse. Is the Street Glide amplifier rack included? Yes. The package includes the 24HDAR-SG black-anodized aluminum amplifier rack and mounting hardware. Is professional tuning recommended? Yes. The front and rear speaker locations, external crossovers, amplifier output and high-power operating levels make professional DSP setup strongly recommended. Need Help Planning Your Street Glide System? Garage Bagger Stereo can help verify Street Glide fitment, speaker impedance selection, amplifier matching, fairing and saddlebag mounting, power and speaker wiring, and factory A2B signal integration before the system is installed. Installation Services Request a Custom Build
THE REFERENCE STANDARD FOR CLEAN POWER INTEGRATION
Plug-and-play is how you build it right the first time—clean signal, correct turn-on behavior, and platform-correct integration without hacks. This is the GBS standard for real output at highway speed.
- No factory wire cutting — no guessing
- Platform-correct harnessing and signal integration
- Compact, motorcycle-ready form factors for real installs
WHAT YOU’RE BUILDING
- Clean install with correct integration
- Real power without splicing
- Factory or aftermarket radio compatibility
- Highway-speed performance you can trust
Plug-and-play amplifiers are the fastest way to go from “stock” to “built right” — clean integration first, then power and tuning.
Why Choose Plug-and-Play Amplifiers for Your Motorcycle
Not all amplifiers are motorcycle-ready. Plug-and-play amplifiers eliminate installation headaches by using platform-correct harnessing, proper signal integration, and compact form factors designed for fairings and saddlebag locations.
- No factory wire cutting — keep the bike clean and serviceable.
- Faster, cleaner installs using bike-specific wiring and mounting solutions.
- Proper signal voltage and turn-on behavior for reliable system operation.
- Compatibility with factory and aftermarket radios when paired with the correct harnessing.
- Reliable performance at highway speed — clean power delivery you can hear.
Built for Harley Touring Platforms
These plug-and-play amplifiers are designed to work with Harley-Davidson touring motorcycles when paired with the correct harnessing and installation parts.
- 2014–2023 Harley touring models
- 2023.5+ CVO and 2024+ touring platforms
- Fairing-mounted amplifier installs
- Saddlebag and rear speaker systems
Always confirm platform year and radio configuration before ordering.
What’s Included in This Plug-and-Play Amplifier Collection
- Motorcycle-specific plug-and-play amplifiers
- Amplifiers designed for fairing and saddlebag installs
- Compatible options for factory and aftermarket radios
- Power solutions for front stage, rear speakers, and subwoofers
- Amplifiers ready for DSP integration
Build the System the Right Way
A plug-and-play amplifier is one part of a complete system. For best results, pair your amplifier with platform-correct speakers, DSP tuning, and installation hardware.
If you’re unsure which amplifier fits your bike or goals, Garage Bagger Stereo can help you select the correct configuration.
High-output systems start with clean integration. Build it once, build it right.
Built to Withstand the Road
DS18 speakers are designed to endure the challenges of the open road while providing exceptional sound quality. Built using durable, weatherproof materials, these speakers are engineered to resist vibrations, impacts, and exposure to the elements without compromising on audio clarity.
Effortless Integration with Your Bagger Motorcycle
Designed for seamless integration, DS18 speakers fit effortlessly into your motorcycle’s audio system without sacrificing space or style. With user-friendly installation and advanced connectivity options, including Bluetooth and RCA inputs, DS18 ensures you can upgrade your sound system without sacrificing functionality.
Customizable Sound for Every Rider
From deep bass to crisp highs, DS18 speakers offer the customization to match your audio preferences. Featuring advanced DSP (Digital Signal Processing) technology, these speakers allow you to fine-tune your sound system for an optimal listening experience. Whether you prefer a balanced sound or a bass-heavy setup, DS18 speakers deliver versatile solutions for your needs.
Shop DS18 Audio at Garage Bagger Stereo
Explore our wide selection of DS18 speakers and motorcycle audio accessories at Garage Bagger Stereo. Whether you’re looking for a minor upgrade or a complete overhaul, we are your trusted destination for premium motorcycle audio gear. With expert guidance and top-notch customer service, we ensure you find the perfect audio solution for your ride.