
-
Description
-
Reviews
2014-2023 Harley-Davidson Road & Street Glide 4-Speaker Audio System | DS18 / Cerwin-Vega
A complete front-and-rear audio package for a compatible 2014–2023 Harley-Davidson Road Glide or Street Glide: a DS18 ION1600.4D four-channel amplifier, two DS18 PRO-HY6.4MSL hybrid front speakers and a Cerwin-Vega ST69CX 6×9 cut-in saddlebag lid kit. Select Road Glide or Street Glide so the amplifier mounting matches your fairing.
Four 4Ω speakers on four dedicated amplifier channels
All four channels of the ION1600.4D are used: two front fairing speakers and two 6×9 saddlebag speakers.
- ION1600.4D: 240W RMS × 4 at 4Ω
- Front: two PRO-HY6.4MSL, 150W RMS each
- Rear: two Cerwin-Vega ST69CX 6×9, 125W RMS each
Key Product Details
| System | Four-speaker front-and-rear plug-and-play system |
| Fits | Compatible 2014–2023 Harley-Davidson Road Glide or Street Glide |
| Options | Road Glide or Street Glide (select before ordering) |
| Amplifier | DS18 ION1600.4D, 240W RMS × 4 at 4Ω |
| Front Speakers | Two DS18 PRO-HY6.4MSL 6.5 in hybrid, 4Ω each |
| Rear Speakers | Two Cerwin-Vega ST69CX 6×9, 4Ω each |
| Radio Interface | DS18 RY-HARNESS.HD, four RCA outputs and remote turn-on |
| Power Wiring | 4-AWG amplifier power kit |
| Rear Mounting | Cut-in saddlebag lid system |
| Saddlebag Cutting | Required |
| Built-In DSP | No |
What Is Included
- DS18 ION1600.4D four-channel Class-D amplifier
- Two DS18 PRO-HY6.4MSL front speakers
- DS18 RY-HARNESS.HD factory-radio harness with four RCA outputs, high-to-low conversion with load resistors, OFC wiring and amplifier remote turn-on
- 4-AWG amplifier power and ground kit
- Road Glide- or Street Glide-specific amplifier mounting
- Cerwin-Vega 6×9 lid kit: one pair of 4Ω ST69CX speakers, cut-in lid grilles, left and right templates, half-inch spacers and speaker wiring
Amplifier Channel Layout
- Channel 1: front-left PRO-HY6.4MSL, 4Ω
- Channel 2: front-right PRO-HY6.4MSL, 4Ω
- Channel 3: rear-left ST69CX, 4Ω
- Channel 4: rear-right ST69CX, 4Ω
No channels are left open. The amplifier produces 240W RMS per channel at 4Ω, while the front speakers are rated 150W RMS and the rear speakers 125W RMS. Set front and rear gains separately where the layout allows, use high-pass crossovers and set gain from measured clean output, not by ear.
Saddlebag Lid Installation
The cut-in kit uses model-specific left and right templates to create the 6×9 openings in compatible factory saddlebag lids, with grilles and spacer rings completing the visible install. Verify that your bike has compatible factory lids before ordering.
- Remove and inspect both saddlebag lids before cutting.
- Confirm template orientation for the left and right lids.
- Check speaker depth and electrical-lock clearance, plus hinge, tether and weather-seal clearance.
- Route the rear-speaker wiring before final lid assembly.
- Seal and protect all cut edges after modification.
- Verify speaker polarity before reinstalling the lids.
Fitment Checklist
- Confirm the model year and exact model, and select Road Glide or Street Glide.
- Confirm the bike keeps a compatible factory radio. Aftermarket-radio installs may need a different signal and remote-turn-on setup.
- Identify any factory amplifier or CVO audio equipment before ordering.
- Front speaker pod modification or spacing may be required.
DS18 ION1600.4D Amplifier Specifications
| Model | DS18 ION1600.4D |
| Type | Four-channel full-range Class-D |
| Output at 4Ω | 240W RMS × 4 |
| Output at 2Ω | 400W RMS × 4 |
| Bridged at 4Ω | 800W RMS × 2 |
| Frequency Response | 10Hz–20kHz |
| Signal-to-Noise Ratio | Greater than 95dB |
| Input Range | 0.2–6V |
| Crossover Modes | LPF / HPF / FULL, 40Hz–2kHz |
| Minimum Impedance | 2Ω stereo / 4Ω bridged |
| Power Input | 4-AWG |
| Published External Fuse | 140A |
| Cooling Fan | Yes |
| Dimensions | 7.32 × 4.72 × 2 in / 186 × 120 × 52mm |
| Built-In DSP | No |
DS18 PRO-HY6.4MSL Front Speaker Specifications
| Model | DS18 PRO-HY6.4MSL |
| Size | 6.5 in / 165.1mm, two-way hybrid |
| Impedance | 4Ω per speaker |
| Power Handling | 150W RMS / 300W max |
| Sensitivity | 97dB |
| Frequency Response | 100Hz–20kHz |
| Recommended High-Pass | 140Hz |
| Compression Driver | 1 in titanium diaphragm, neodymium |
| Cone | Water-resistant treated paper |
| Weather Rating | IP65 |
| Mounting Cutout | 5.6 in / 142mm |
| Mounting Depth | 2.82 in / 72mm |
Cerwin-Vega ST69CX Rear Speaker Specifications
| Model | Cerwin-Vega ST69CX |
| Size | 6×9 in, two-way coaxial |
| Impedance | 4Ω per speaker |
| Power Handling | 125W RMS |
| Sensitivity | 90.5dB, 1W/1m |
| Frequency Response | 45Hz–20kHz |
| Cone | Polypropylene |
| Tweeter | Titanium diaphragm, neodymium magnet |
| Water Resistance | IPX5 |
| Mounting Depth | 4.25 in / 107.9mm |
| Lid Kit Includes | Cut-in grilles, left and right templates, half-inch spacers, speaker wiring |
Specifications per Cerwin-Vega.
Related Paths
2014-2023 Harley 4-Speaker System FAQ
Which motorcycles does this system fit?
Compatible 2014–2023 Harley-Davidson Road Glide and Street Glide motorcycles. Select the correct fairing style before ordering.
How many speakers are included and what impedance are they?
Four: two DS18 6.5-inch front speakers and two Cerwin-Vega 6×9 rear speakers. All four are nominal 4Ω.
How much power does the amplifier produce?
The ION1600.4D is rated 240W RMS × 4 at 4Ω, 400W RMS × 4 at 2Ω or 800W RMS × 2 bridged at 4Ω.
Do the saddlebag lids need to be cut?
Yes. Both compatible factory saddlebag lids must be permanently cut for the Cerwin-Vega 6×9 lid system.
Does the factory radio wiring need to be cut?
No. The compatible factory-radio connection uses the plug-and-play DS18 harness.
Does the amplifier include DSP?
No. It has gain and crossover controls but no integrated digital signal processor.
Why does gain setup matter so much?
The amplifier can produce more continuous power per channel than the speakers are rated to handle, so gain and crossovers must limit clean output to safe levels.
Are the speakers weather resistant?
The DS18 front speakers are IP65 rated and the Cerwin-Vega rear speakers are rated IPX5. Neither should be treated as submersible.
Is the Road Glide amplifier mounting the same as the Street Glide one?
No. The mounting solution must match the selected motorcycle.
Is professional installation recommended?
Yes. The package needs amplifier wiring, measured gain setup, fairing work and permanent saddlebag lid modification.
Need Help Choosing?
Call or start a build consultation and we will confirm fitment, channel plan and wiring before you order.
